Shenzhen Xinhui Wireless XH-X6 4 in 1 wireless charger User Manual
- August 19, 2024
- Shenzhen Xinhui Wireless
Table of Contents
Shenzhen Xinhui Wireless XH-X6 4 1 wireless charger
Specifications
- Product name: 4 in 1 wireless charger
- Input: 9V 3A
- Mobile phone output: 5W/7.5W/10W/15W
- Earphone output: 3W (max)
- iWatch output : 2.5W (max)
- Night lamp output : 1W (max)
Product introduction
Thank you for purchasing our products! This product is a 4 in 1 wireless charger that supports power charging of Qi-compatible mobile phones/ iWatch/ TWS Bluetooth earphones. One wireless charger can charge up to 3 devices at the same time. It can also work as a night lamp. It brings you an easy charging experience without the hassle of entangling wires.
Product Appearance
iWatch charging part installation
Lift the upper to charge the mobile phone
Notice: The removable watch charging part cannot work alone, it can only
work with this specific product. If plugged into other products, it will be
damaged.
Night lamp touch switch
- One-time press, white light
- Press twice, warm light
- Three-time press, turn off the light
Operating steps
- Power on the device with the fast charger and Type-C charging cable we provide first.
- After being connected to the power supply, the night lamp will flash for 3 seconds and then turn off; then it will stay off when the wireless charger is in standby mode; it also stays off during charging. Night lamps in white light will flash when metal objects are detected or the charging status is abnormal.
- When charging, if the device is a Qi-enabled mobile phone, iWatch, or TWS Bluetooth earphone, just put the device in the corresponding charging area and it will start charging in 1 second. When the device is fully charged or you want to terminate the charging, just remove it from the charging area.
Product parameters
- Product name: 4 in 1 wireless charger Input: 9V 3A
- Mobile phone output : 5W/7.5W/10W/15W
- Earphone output: 3W (max)
- iWatch output: 2.5W (max)
- Night lamp output : 1W (max)
Accessory list
- Wireless charger*1
- 1M Type C Cable*1
- User manual*1
Indicator status
Certification standard
- National Quality Assurance standard-Executive standard: GB/T1095-2003
- CE Executive standard: EN55032, EN55035, EN61000-3-2, EN 61000 FCC Executive standard: FCC47 CFR Part 15c
- UL Executive standard: UL62368
- ROHS Executive standard : ROHS2.0
FAQ
- Please put the phone/AirPods/Watch at the center of the charging area.
- To achieve fast charging, Please use a charger above QC18W or PD20W to supply power to the wireless charger.
- The charging distance is 0-2mm, please don’t wear a protective case that is thicker than 2mm. (Magnetic and metal attachments or credit cards will influence the charging stability, please remove them before charging).
- The watch has a temperature control feature, when the temperature reaches 45°C, the device will stop charging automatically. If the temperature becomes normal, it will continue to charge.
- The lower the temperature is, the faster the charging speed is. The charging speed is faster in winter than in summer.
- Please don’t charge high-temperature temperature and humid environments to avoid damage to the circuit.
- Put it at taplace that children can’t reach to avoid unnecessary accidents.|
- Please place the charger away from flammable and explosive liquids or gases.
- If you have any problems with this wireless charger, please feel free to contact the seller service, we will offer you the best solution within 24 hours. Your safety and experience are our top priority, we have it all covered.
FCC ID Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.If this equipment does cause harmful
interference to radio or
television reception,which can be determined by turning the equipment off and
on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
FCC ID ：2BHXI-XH-X6
FAQ
- Q: Where should I place the phone/AirPods/Watch for charging?
- `A: Please put the phone/AirPods/Watch at the center of the charging area.
- Q: How can I achieve fast charging?
- A: To achieve fast charging, use a charger above QC18W or PD20W to supply power to the wireless charger.
- Q: What is the recommended charging distance?
- A: The charging distance is 0-2mm. Please avoid using protective cases thicker than 2mm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>