Swiss Madison 2T140 Two Piece Toilet Instruction Manual
- August 17, 2024
- Swiss Madison
Table of Contents
Swiss Madison 2T140 Two Piece Toilet
Product Specifications
- Product: Two-Piece Toilet
- Manufacturer: Swiss Madison
- Contact: 1-434-623-4766 | info@swissmadison.com
FAQ
Q: What is the warranty period for the Two-Piece Toilet?
A: The product comes with a one-year limited warranty. Please contact us directly for warranty claims.
Q: What is covered under the warranty?
A: The warranty covers manufacturing defects. It does not cover damages due to chemicals, accidents, or other external factors.
Q: How can I reach customer support for further assistance?
A: For any questions or concerns, please contact us at 1-434-623-4766 or visit our website at www.swissmadison.com.
PRIOR TO INSTALLATION
-
Inspect toilet to ensure no damages have occurred while in shipping.
-
Observe all plumbing and building codes in accordance with your state and local requirements.
-
All dimensions are nominal! Be sure to measure your toilet prior to installation.
-
The step-by-step guidelines in the installation instructions are a general reference.
Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional. -
Read installation and maintenance instructions thoroughly before installing.
Be sure to use proper tools and always wear proper personal safety accessories for your protection. -
Two people are recommended to handle and install this product as it is fragile.
-
Fill valve has been factory-tightened to design specifications. If re-tightening is required, use a wrench a tighten one turn past finger tight.
-
Make sure the supply pressure is a minimum of 35 psi (2.5kg/cm³), the toilet will not function properly without minimum water pressure.
QUESTIONS OR CONCERNS?
Please contact us:
1-434-623-4766
info@swissmadison.com
INCLUDED PARTS
SUGGESTED TOOLS & MATERIALS
INSTALLATION
-
Turn Off Water Supply
- Close toilet supply valve and flush tank completely, use towel to remove excess water.
- Disconnect and remove supply line, if you are replacing the valve shut main water supply first.
- Remove closet bolts from flange and clean wax and putty from base area.
-
Rough-In the Toilet
Measure the wall from behind the toilet to the middle of the closet bolt. Your rough-in measurement should be 12″.
-
Install Anchors & Brackets
- Remove the toilet bowl and measure the thickness of the bowl. Then apply that measurement in towards the center from the marks on the floor.
- Insert anchors and install brackets.
-
Install Wax Seal
Invert toilet on floor (use cushion to prevent damage), and install wax ring evenly around waste flange with tapered end of ring facing toilet. Apply thin bead of sealant around the toilet base.
-
Align Connector & Secure Toilet
- Align connector and carefully lower over brackets.
- Install floor mounting kit
-
Install Toilet
- Position toilet square to wall and with a rocking motion, press down fully on wax ring. Alternately tighten nuts until toilet is firmly sealed to floor. Do not overtighten.
- Smooth off the bead of sealant around the base. Remove excess sealant.
- Connect water supply to shut off valve, and check for leaks. Tighten if necessary.
-
Connect Supply Hose
Thread the supply hose onto the tank . -
Attach Gasket
Position the gasket on the bowl inlet. -
Position Tank onto Bowl
Holes should line up so threaded rod can fit smoothly connecting the cistern body to the bowl. -
Secure Tank to Bowl
- Slide metal washer & rubber washer onto bolt.
- Thread bolts into the bottom of the tank then tighten the bolts using a screwdriver.
- Do not overtighten, this may crack the ceramic.
-
Secure Tank
- Using screws and washers affix tank to wall.
- Tighten to secure in place, do not overtighten.
-
Connect Plumbing
Connect water supply. -
Connect Push Button
- Unscrew the big white nut on the push button and insert the button into the hole on the tank.
- When the rods meeet the push buttons, measure the height (H) with a ruler.
- Unscrew the rods and cut the part H on both rods.
- Insert the rods back and tighten the small nut.
- Tighten the big nut from the inside of the tank.
-
Check for Leaks
Flush several times and check for leaks.
TOILET SEAT INSTALLATION
-
Disassemble
Disassemble the cover cap and the hinge. -
Construct Hinges
-
Insert screw and nut into the hole on the hinge.
-
Attach blind hole screw fixing to the bottom of screw.
-
Attach Hinges
- Insert hinges with blind hole screw fixings attached into holes on toilet bowl.
- Lightly tighten hinges with a screwdriver too allow for later adjustment.
-
Adjust and Cover Hinges
- Be sure the hinge is all the way forward for proper seat fitting.
- Place the covers onto the hinges.
-
Adjust and Attach Seat
- Align seat to the hinges then firmly tighten the hinges.
- Attach seat to the secure hinges.
- Adjust seat to align to the bowl.
TOILET SEAT USAGE
- To remove, push middle button until you hear a “click”, then pull straight up.
- To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.
ONE YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our customers with beautiful, durable, long-lasting products. Should there be any defects in materials or craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison® will provide replacement parts at no charge, or at its discretion, replace any product or part of the product that is deemed defective, under normal installation, use, service or maintenance. This warranty applies only to the original purchaser. Proof of purchase will be required in the instance of a claim. Swiss Madison® recommends all installations of Swiss Madison® products to be conducted by a licensed, professional plumber or contractor. Swiss Madison® will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional for installation. Swiss Madison® is not responsible for any installation or removal costs.
THIS ONE YEAR LIMITED WARRANTY WILL BE VOIDED IF:
- The installation recommendations were not followed by the installer
- The product has been moved from its initial place of installation
- The product has in any way been modified from its packaged state
- The product has been subjected to improper maintenance, abuse, misuse, excessive use of chemicals, accidents, or other damages, etc.
Swiss Madison® makes no implication that its products comply with any local
building or plumbing codes. It is the consumer’s responsibility and obligation
to determine local code compliance prior to and during installation. This
warranty extends only to the original purchaser and first consumer. Swiss
Madison® is not responsible for any special, incidental or consequential
damages associated with the installation, replacement, return or use of the
original purchaser’s product. This includes, but is not limited to: freight
costs, labor, travel time, lost profit, home damages and other contingent
liabilities and costs (including, without limitation, costs associated with
‘professionals’ or ‘experts’, investigations, audits, analyses, attorneys and
any other professional/hired services).
The Swiss Madison® warranty is a comprehensive and explicit limit of
liability. All items not disclosed within the warranty are not addressable
within the responsibility of Swiss Madison®. Certain states have variances
regarding implied warranties; in those situations, we remain fully compliant.
QUESTIONS OR CONCERNS?
Please contact us directly at 1-434-MADISON (623-4766)
WARNING:
Contents of your order may contain sharp and possibly other harmful pieces and
may cause hazard to children and adults. Swiss Madison® is not responsible in
any way for personal damages.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>