Swiss Madison SM-BV662 Classe 18.13 in. D x 33 in. H Bathroom Vanity Instruction Manual
- June 4, 2024
- Swiss Madison
Table of Contents
SM-BV662 Classe 18.13 in. D x 33 in. H Bathroom Vanity
Instruction Manual
@SwissMadison
#WellMadeForever
www.swissmadison.com
1-434-623-4766
[email protected]
PRIOR TO INSTALLATION
- Inspect product to ensure no damages have occurred while in shipping.
- Observe all plumbing and building codes in accordance with your state and local requirements.
- The floor must be level prior to the installation of the vanity.
- All dimensions are nominal! Be sure to measure your vanity prior to installation.
- The step-by-step guidelines in the installation instructions are a general reference. Should there be any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss Madison products by hiring a licensed professional.
- Read installation instructions thoroughly before installing. Be sure to use proper tools and always wear proper personal safety accessories for your protection.
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
SUGGESTED TOOLS & MATERIALS
INCLUDED PARTS:
Parts for Reference
Prepare Frame
- Insert 2 wooden dowels (C) and 4 screws (H) into the front crossbar (4) as shown.
- Insert 4 wooden dowels (C) and 4 screws (H) into the rear top bar (5) as shown.
- Insert 6 wooden dowels (C) into the rear bottom bar (6) as shown.
- Tighten all screws into their respective wooden bars. Be sure to leave about 2-3 mm of the screw exposed above the board. Be careful not to overtighten.
Prepare Side Panels
- Screw 5 cam bolts (A) into the left side panel (2). Repeat for the right side panel (3).
- Insert 2 wooden dowels (C) into the left side panel (2) as shown. Repeat for the right side panel (3).
- Screw 4 screws (H) into the left side panel (2) as shown, being careful to not overtighten.
Leave about 2-3 mm of the screw exposed above the panel. Repeat for the right side panel (3).
Assemble Frame
- Use 5 cam locks (B) to attach the left side panel (2) to the front cross bar (4), rear top bar (5), and rear bottom bar (6).
- Repeat for the right side panel (3).
Attach Base
- Place the base panel (1) onto the cabinet frame as shown.
- Insert 5 screws (D) into the base panel as shown. Using an Allen key (G), secure the base into place.
Install Legs
- On the underside of the base panel (1), place a leg mount (PM1) into a corner, lining up the holes. Secure in place using 5 screws (H) as shown. Repeat this process using the remaining 3 leg mounts (PM1).
- Remove the cap from a leg (LT22A2) as shown in the diagram. Repeat for all 3 remaining legs (LT22A2).
- Twist the legs (LT22A2) into the center hole of the leg mount (PM1) by referencing the diagram until they are secured into place.
Prepare Cabinet for Installation
-
Insert corner brace (BC67) into the corner of the cabinet as shown. Tighten all screws to secure into place.
Repeat for the last 3 corners using an additional 3 corner braces (BC67). -
Use a level to verify the cabinet is level on all sides.
Optional: Remove the backing of a foam pad (I). Place the foam pad sticky side down onto the top of the cabinet as shown. Repeat with all foam pads (I), placing them evenly around the perimeter of the cabinet top.
| 
---|---
Secure Vanity to Wall
- Select the installation method from below. Please note that mounting hardware is not supplied with this vanity.
Option 1: Securing to Drywall
- Position the cabinet against the wall in the desired location.
- Using a pencil, make a mark on the wall through the holes in the rear top bar (5).
- Move the cabinet away from the wall. Create a pilot hole in each mark on the wall, then insert a plastic anchor.
- Place cabinet against the wall, insert a screw through the rear top bar (5) into each hole in the wall, then tighten to plastic anchors to secure the vanity.
Option 2: Securing Drywall & Wood Stud
- Position cabinet against the wall in the desired location, be sure desired mounting location aligns with existing wood studs.
- Insert mounting screw through the hole in the rear top bar (5), then tighten through the drywall into the wooden stud. Repeat this step for the side to secure the vanity.
Vanity Top Installation
- Install faucet and drain according to manufacturer’s installation instructions. Do not over tighten, this may cause the sink to crack.
- Set the vanity top on top of the vanity base, checking the location of the p-trap and drain.
- Remove vanity top from vanity base. Apply a thin bead of silicone around the vanity base and set the vanity top carefully in place.
- Remove excess silicone with a wet cloth.
Attach Doors
- Install 2 hinges (HS26A) to the left door (7) and right door (8) using 2 screws (H) per hinge.
- Use an additional 2 screws per hinge to attach the doors (7) (8) to the cabinet. If the doors do not align properly, adjust the hinges according to the diagrams below. Once adjustments have been completed, secure the hinges using 2 screws (H) each.
- Install the handles (E) to the doors (7) (8) using the handle screws (F) as shown.
Hinge/Door Adjustment and Realignment
- If adjustment or realignment is needed, follow the instructions provided in the following chart.
ONE-YEAR LIMITED WARRANTY
Swiss Madison products are made with quality materials and excellent
craftsmanship to provide our customers with beautiful, durable, long-lasting
products. Should there be any defects in materials or craftsmanship under
regular use that are discovered within the first year of installation, Swiss
Madison will provide replacement parts at no charge, or at its discretion,
replace any product or part of the product that is deemed defective, under
normal installation, use, service or maintenance. This warranty applies only
to the original purchaser. Proof of purchase will be required in the instance
of a claim.
Swiss Madison recommends all installations of Swiss Madison products to be
conducted by a licensed, professional plumber or contractor. Swiss Madison
will not be held responsible for any damage or product failure due to improper
installation, misuse, or failure to utilize a licensed professional for
installation. Swiss Madison is not responsible for any installation or removal
costs.
This One Year Limited Warranty Will Be Voided If:
- The installation recommendations were not followed by the installer
- The product has been moved from its initial place of installation
- The product has in any way been modified from its packaged state
- The product has been subjected to improper maintenance, abuse, misuse, excessive use of
chemicals, accidents, or other damages, etc.
Swiss Madison makes no implication that its products comply with any local
building or plumbing codes.
It is the consumer’s responsibility and obligation to determine local code
compliance prior to and during installation. This warranty extends only to the
original purchaser and first consumer.
Swiss Madison is not responsible for any special, incidental, or consequential
damages associated with the installation, replacement, return or use of the
original purchaser’s product. This includes, but is not limited to: freight
costs, labor, travel time, lost profit, home damages, and other contingent
liabilities and costs (including, without limitation, costs associated with
‘professionals’ or ‘experts’, investigations, audits, analyses, attorneys and
any other professional/hired services).
The Swiss Madison warranty is a comprehensive and explicit limit of liability.
All items not disclosed within the warranty are not addressable within the
responsibility of Swiss Madison. Certain states have variances regarding
implied warranties; in those situations, we remain fully compliant.
If you have any questions or concerns, please contact us directly at
1-434-MADISON (623-4766)
WARNING: Contents of your order may contain sharp and possibly other
harmful pieces and may cause hazards to children and adults. Swiss Madison is
not responsible in any way for personal damages.