PROGRESS LIGHTING P560361 1-LT Outdoor Lantern Installation Guide

: August 17, 2024
: PROGRESS LIGHTING

Table of Contents

PROGRESS LIGHTING P560361 1-LT Outdoor Lantern
Models
PACKAGE CONTENTS
Safety Information
Preparation
Care And Maintenance
Assembly Instructions
WARRANTY
CONTACT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROGRESS LIGHTING P560361 1-LT Outdoor Lantern

Models

PACKAGE CONTENTS

PART	DESCRIPTION	QUANTITY
P560361	P560362
A	Fixture	1
B	Acrylic Shade	1

HARDWARE CONTENTS
(not actual size)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
WARNING: To comply with the National Electrical Code and Underwriters Laboratories requirements, when installed outdoors, or in wet locations, the edge of the wall plate coming in contact with the mounting surface, must be sealed with a latex waterproof caulking to prevent water from entering the outlet box.

Preparation

Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Estimated assembly time: 30 minutes.
Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care And Maintenance

Shut off main power supply before cleaning product or changing light bulbs.
To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

FOR P560361

Attach the back plate (CC) to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.

FOR P560362

Place the Back Plate (DD) against the wall, ensuring the position is vertical, mark the two mounting holes. Using a (2) 01/4 (06.4mm) drill bit, drill the pilot holes at the marked positions.
- Insert the Wall Anchors (GG) to the holes, screw the two Screws (FF) into the Wall Anchors (GG), but do not fully tighten them. Install the Back Plate by sliding the key slot holes over and down onto the Wall Anchor Screws, tighten the Wall Anchor Screws to secure the Back Plate.
- Attach the back plate (DD) to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Strip 3/8″ of insulation from the electrical wire ends. Using wire connectors (BB), connect the white fixture wire to the white supply wire from the outlet box; connect the black fixture wire to the black supply wire from the outlet box.
- Connect the fixture ground wire and supply ground wire using a wire connector or by fastening to the ground screw on the back plate. Push all of the wire connections carefully into the outlet box.
Attach the fixture (A) to the back plate (CC or DD) of the outlet box by installing the flat head screws (AA) and plastic sealing washers (EE). Tighten the fixture against the mounting surface.
Thread the lamp (not included) into the fixture socket.
- Use 18-watt LED medium base lamp.
- Attach the acrylic shade (B) by sliding it through and down the top of the upper arm of the fixture (A).

Assembly and Installation Instructions

Caution: Read instructions carefully and turn off power at central circuit breaker before starting the installation.

CAUTION: Read instructions carefully and turn off power at central circuit breaker before beginning installation.
WARNING: Fire hazard. Min 90°C power conductors. Consult a qualified electrician to ensure proper good branch circuit conductor.
WARNING – If there are other regulating mechanisms used with this device, carefully follow instructions for meeting NEC requirements. If you have any questions, consult a qualified electrician.
CAUTION – Glass is always fragile; Handle the component(s) and/or bulb(s) with care.
WARNING: When installing outdoors or in damp locations and in order to meet Code requirements
National Electric as well as Underwriters Laboratories, it is necessary that the edge of the wall plate which touches the surface the mounting plate must be coated with an airtight latex sealant to prevent water from entering the outlet housing.

WARRANTY

WARRANTY AND EXCLUSIVE REMEDY

Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers’ sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress’s sole and maximum liability for a defective product shall never exceed the cost of the subject product.

EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS.

Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer’s responsibility. Customer is responsible for determining the suitability of our products for customer’s use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.