Amba RSWH-P Heated Towel Rack Installation Guide

: August 17, 2024
: Amba

Table of Contents

Amba RSWH-P Heated Towel Rack
Product Information
Product Usage Instructions
INCLUDED COMPONENTS
SAFETY INFORMATION
INSTALLATION INSTRUCTIONS
OPERATING INSTRUCTION
CARE & MAINTENANCE
AVAILABLE MODELS
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Amba RSWH-P Heated Towel Rack

Product Information

Specifications

Electrical Info: 150 watts, 1.3 amps, 120 volts
Models Available: RSWP-M B
Warranty: Two-year limited warranty with proof of purchase

Product Usage Instructions

Installation Instructions – Plug-In
Before starting assembly, ensure all components listed are in the package:

Component A: 22 7/16″ (570mm)
Component B, C: 18 7/8″ (480mm)
Component F: Switch

Note: The center of the wall plate should be at 3 1/8″ (80mm). Do not over-tighten the set screw. Turn the unit on using the switch.

Care & Maintenance
This towel warmer has been designed to run continuously. Turn off the switch or unplug the cord when not in use for long periods of time.

Operating Instructions

After installation, connect the electric power.
Remove the protective cover from the switch and turn it to the on position.
The indicator light will glow red, and the towel warmer will start to heat up.
Allow 10-20 minutes for the towel warmer to heat up.

FAQ

Q: How do I know if the unit is on?
A: The switch will illuminate when the unit is powered on.
Q: Can I use an extension cord with the plug-in models?
A: Never use an extension cord for plug-in models.
Q: What to do if the surface of the unit becomes hot?
A: Take caution as the surface of the unit is hot when on. Avoid direct contact.

INCLUDED COMPONENTS

TOOLS REQUIRED

SAFETY INFORMATION

Please read the following information before installing and using your Heated Towel Rack.

WARNINGS

These units should be installed by a certified electrician in accordance with the National Electrical Code (NEC) and the Canadian Electrical Code (CEC).
The unit requires a 120 volt, 60Hz power source and should be installed on a GFCI-protected circuit.
Plug-in units should be connected to a grounded outlet with a minimum rating of 10 amps.
Follow installation instructions to ensure unit is securely fixed to wall. Unit is designed for drying towels. Under no circumstances should anybody climb on or hang on unit.
Unit is intended for indoor use only. Do not place units inside a shower, sauna, steam room, or wherever unit would be exposed to water.

CAUTION

As this is a heating device, the surface temperature can increase depending on the ambient temperature in the room and the number of towels applied to the unit.
Overloading the unit will cause the unit to become extremely hot and may result in a burn if touched and/or damage to towels.
The fasteners provided with the installation kit are for convenience only and are not suitable for all installation conditions.
It is the ultimate responsibility of the installer to ensure suitable mounting hardware is used.

INSTALLATION INSTRUCTIONS

PLUGIN
BEFORE STARTING ASSEMBLY MAKE SURE ALL COMPONENTS LISTED ARE IN THE PACKAGE

CAUTION — SURFACE OF UNIT IS HOT WHEN ON!

HARDWIRED
BEFORE STARTING ASSEMBLY MAKE SURE ALL COMPONENTS LISTED ARE IN THE PACKAGE

CAUTION — SURFACE OF UNIT IS HOT WHEN ON!

PLUG-IN MODELS

INTEGRATED SWITCH

The Radiant Collection features an Integrated on/off switch.
Remove plastic cover after installation.
Switch is located on the bottom of the right vertical bar.
Press switch to power on unit.
Switch will illuminate when on.

OPERATING INSTRUCTION

After installation, connect the electric power.
Remove the protective cover from the switch and turn it to the on position.
The indicator light will glow red and the towel warmer will start to heat — Allow 10-20 minutes to heat up.
This towel warmer has been designed to run continuously — Turn off the switch or unplug the cord when the towel warmer is not in use for long periods of time.
Never use an extension cord for Plug-in models.

CARE & MAINTENANCE

Towels that contain soap or detergent residue may appear to have scorch marks; this is simply discoloration of the residue in the towels themselves.
The unit is constructed from extremely durable 304 stainless steel. To maintain a good appearance, follow these simple instructions:
For routine cleaning, simply switch off the unit, allow to cool to room temperature, wipe with a damp cloth and buff with a soft, dry cloth.
Under no circumstances should abrasive cleaners be used to clean the unit.