PawHut D06-095 Dog Stair Safety Gate Dog Barrier Instructions

PawHut D06-095 Dog Stair Safety Gate Dog Barrier

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.

Dear Customer

Thank you for purchasing this product. SO that your appliance serves you well, please read all the instructions in this user’s manual. if you have any questions, please contact our customer care center, Our contact details are blow.

Country

|

Phone

|

Email

---|---|---
Us| 001-877-644-9366| customerservice@aosom.com

 BEFORE USING PRODUCT

IMPORTANT

• Improper installation could result in the gate becoming unstable or dislodged from the doorway.

• Base locks are to be used at all times, on both sides of the gate.

• This product will not necessarily prevent all accidents.
  Check the gate regularly to see if all the hardware and mount – ings are tightened.

• Do not use if any components are missing or damaged.

• STOP using when a pet can climb over or dislodge the gate.

• Additional or replacement parts should only be obtained from the manufacturer or distributor.

WARNING

Children have died or been seriously injured when gates are not securely installed.

• ALWAYS install and use gates as directed using all required parts.
• YOU must install wall cups to keep gate in place.Without wall cups, child can push out and escape.
• STOP using when a child can climb over or dislodge the gate.
• USE only with the locking mechanism securely engaged.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Intended for use with children between 6 and 24 months.
• Install according to manufacturer’ s instructions.

PARTI

HARDWARE

EXTENSIONS AND MAX SIZE

• No EXTENSION 29-31 inch

• 36-38 inch

• With 8 inch 37-39 inch

• With 12inch 41-43 inch

INSTALLING YOUR GATE

STEP 1
Locate the (4) threaded spindle rods (B).
Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot (Figure 1-1)

NOTE You may notice a slight gap between the gate door latch and the frame (Figure 1-2)

THIS IS NOT A DEFECT this gate is a pressure mounted gate and this gap will disappear once you tighten the gate in its opening.

DO NOT REMOVE THE ZIP TIE UNTIL INSTALLATION IS COMPLETE. (Figure 1-3)

STEP2

Insert the threaded spindle rods with adjustment wheels into the hole on all four corners of the sides of the gate. (Figure 2-1)

Place the gate in desired opening with the bottom close to the floor. The distance between the bottom of the gate Figure 2-1 and the floor should be less than 1/8  inch (Figure 2-2). Once you are satisfied with the placement of your gate trace the spindle rods rubber feet onto the surface of your opening making sure 1/8 inch these are level (Figure 2-3}Then remove t the gate from the opening. Then screw the 4 wall cups to the wall using the screws (Figure 2-4J or paste the 4 wall cups using the stickers provided (Figure 2-5).

STEP3

Insert all 4 threaded spindle rods into the wall cups (Figure 3-1) Tighten the wheels using the spanner tool. (Figure 3-2 and Figure 3-3) Do not over tighten. It may be necessary to hold the threaded spindle rods while rotating the adjustment wheels to ensure that the entire unit does not rotate while installing the gate.

NOTE if your door latch is not properly engaging with the receiving component, ensure that your gate is level, mounted properly and that you have not over-tightened the adjustment wheels.

NOTE The gap between the gate and the wall should not exceed more than 2.5 inch on either side (Figure 3-4 and 3-5)
If the gate has been installed properly the gap between the door latch and frame should now be closed (Figure 3-6)

REMOVING YOUR GATE FROM THE WALL

To remove your gate from the wall, rotate the adjustment wheels on each of the (4) threaded spindle rods to depressurize the gate from its doorway or opening. Then, gently pull or push the gate free from its doorway or opening.

CARE AND MAINTENANCE

Periodically check the gate for signs of damage, wear, or missing components.
Do not use if any part is missing, worn or damaged.
Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by span in with warm water and a mild detergent.

Imported by Aosom LLC
27150 SW Kinsman Rd Wilsonville, OR 97070 USA
MADE IN CHINA
IMPORTER ADDRESS:
MH STAR UK LTD
Unit 27, Perivale Park,
Horsenden lane South
Perivale, UB6 ?RH
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>