PROGRESS LIGHTING P350274 10.24 Inch Matte Black Flush Mount Ceiling Light Small Instruction Manual
- August 15, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P350274 10.24 Inch Matte Black Flush Mount Ceiling
Light Small
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANT | QTY |
|---|---|---|---|
| P350274 | P350275 | ||
| A | Fixture | 1 | 1 |
| B | Diffuser | 1 | 1 |
| C | Decorative trim | 1 | 1 |
| D | Knurl nut | 3 | 3 |
Overview
HARDWARE CONTENTS
Safety Information
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
- CAUTION : Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.
- CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
- WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
- CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.
Care and Maintenance
- Shut off the main power supply before cleaning products or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
- Screw down the screws (AA) into the junction box, but only screw them down halfway.
- Unscrew the Knurl nuts (D), and remove the Decorative trim (C) and the Diffuser (B) from the fixture (A). Make sure to keep track of the knurl nuts (D) for use later
- Strip 3/8″ of insulation from the electrical wire ends. Using wire connectors (BB), connect the WHITE fixture wire to the WHITE supply wire from the junction box; connect the BLACK fixture wire to the BLACK supply wire from the junction box. Connect the fixture ground wire and supply ground wire using a wire connector. Push all of the wire connections carefully into the junction box.
- Align the keyhole on the fixture (A) with the screws (AA). Use the larger hole of the keyhole slot to allow the screw heads to pass through the fixture. Then rotate the fixture clockwise so that the screw heads secure into the smaller side of the keyhole slot. Finally, tighten the screws (AA) all the way down firmly into the J-Box.
- Select color temperature.
- Place the diffuser (B) onto the trim ring (C), then align the holes from the trim ring (C) to the fixture screw post (A). Use the knurl nut (D) to secure them all tightly together.
- Secure the fixture (A), and verify that the fixture is flush with the ceiling.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>