BELL plus HOWELL Bionic Color Burst Landscape Light Instructions

Color Burst Landscape Light
Instructions

PARTS & FEATURES

1. Large solar panel
2. LED Lights
3. ON/OFF button
4. Adjustment Knob
5. Main Swivel Arm
6. Mounting Plate
7. Ground spike
8. Stake

Package includes:

• 2 Bionic Color Burst units,
• 4 screws,
• 4 plastic anchors,
• 2 ground spikes,
• 2 stakes

INSTALLATION

PLEASE READ THIS MANUAL CAREFULLY BEFORE USE AND KEEP IT FOR FUTURE USE.

• When picking a place to install your Bionic Color Burst, CHOOSE A LOCATION WITH MAXIMUM SUN EXPOSURE DURING THE DAY.
• Do not use the solar light to force the stake into the ground. First, insert the stake into the ground and then place the solar light over the stake.
• Awoid areas under trees or bushes as this will prevent a proper charge of the Bionic Color Burst.
• Do not install Bionic Color Burst near an existing outdoor light. The built-in sensor will prevent it from turning the solar lights on.
• When using the Bionic Color Burst in the fall and winter, please note that due to fewer daylight hours, the batteries might not charge fully. This may affect the amount of time the Bionic Color Burst will be on.
• During cold winter months, we recommend to remove the Bionic Color Burst to prevent damage to the unrt due lo frost and freezing temperatures.

MOUNTING UNIT

• Choose a location with maximum sun exposure
• Drill 2 holes matching the pattern on the Mounting Plate and install plastic anchors (included)
• Attach the Mounting Plate using 2 screws (included)

FOR IN-GROUND INSTALLATION

| |
---|---|---
1. insert Ground Spike into the Stake| 2. Make sure the soil is softened Insert Stake into the ground| 3. Insert sonic color Burst  over the Stake

ADJUSTING ANGLES

• Adjust the angle of the Bionic Color Burst to direct the light where needed by loosening the Adjustment Knob (4)
• Once desired angle has been selected, tighten the knob

USAGE

Make sure you read and follow the installation directions prior to use

1. Leave the unit under direct sunlight for solar charging at least 6 hours UNIT NEEDS TO  BE FULLY CHARGED BEFORE INITIAL USE.
   If there isn’t ample sunlight, it may take longer for the batteries to charge.

2. Once it becomes dark, press the ON/OFF button once to turn on the white light.
   Press the ON/OFF button again for purple light.
   Press it again for blue light.
   Press it again for continuing color changing light.

3. The Bionic Color Burst will turn off during the day or if unit runs out of battery.

TROUBLESHOOTING

it can get maximum sun exposure for 6 hours.
Unit is turned OFF.| Press the ON/OFF switch.
Unit is located near a strong light source.| Make sure unit is installed away from any strong light sources, such as an existing outdoor light.
Unit is placed under trees.| Move the unit to another open location.
Solar panel is dirty, or covered up.| Wipe the solar panel clean and make sure it is always free of debris.

TECHNICAL INFORMATION

Product size: light. 4.25” Χ 5.51″ Χ 2.6′ (108 Χ 140 Χ 66 mm)
Stake: diameter 0.91″ Χ 9.84″(23 Χ 250 mm)
Net weight: 0.634lb/288g
Battery Run Time: 11 hrs (when fully charged)
Battery Charge Time: 6 hrs
Voltage: 3.7V
Maximum Wattage: 0.5W
IPX Rating: IP65
LED Lifespan: 50,000 hrs

BELL + HOWELL ® BIONIC COLOR BURST ™
ITEM NO. 8208FELN
DISTRIBUTED BY EMS9 NE YORK, NY 10001 USA
© 2022 ENSON® ALL RIGHTS RESERVED.
MADE IN CHINA.
emsoninc.com
1.800.423.4248

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>