Scylla 2022-04-01 Electric Robe Warmer Instructions

**Scylla 2022-04-01 Electric Robe Warmer Instructions

**

FITTING INSTRUCTIONS

Scylla Electric Robe Warmer GB (Cable and plug).

Scylla Electric Robe Warmer GB (Cable and plug).

We want to thank you for choosing one of our products. We are confident that you will be happy with your selection because its quality and finish ensure comfort day after day. By following the suggestions contained in this manual, the product you have purchased will operate without problems giving you optimum comfort.

SAFETY INFORMATION

This product is designed to operate at 230 V
Ensure all electrical power is switched off completely when any electrical work is being completed on the Robe Warmer.
The electrical installation must comply with local or national wiring regulations. Using the supplied schuko plug does not require a qualified electrician. For an electrically fixed installation of this product, a qualified electrician is required.
If the supply cord is damaged, this must be replaced by the manufacturer, its service agent or similarly a qualified person in order to avoid hazard.
When moving the product ensure the Robe Warmer is carried by the metal frame and not the electric cable.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children must not play with this appliance.
Do not climb on the radiators or use them as sports equipment.
For the correct installation of this product, it is essential that fixing is carried out in such a way that it is suitable for intended use and predictable misuse. A number of elements need to be taken into consideration including the fixing method used to secure it to the wall, the type and condition of the wall itself, and any additional potential forces or weights that may happen to be applied to the unit, prior to finalising installation.
This product can be hot when in use, and as such, presents a risk of burns to users on prolonged contact.
Installers and users should ensure that those who may come into close proximity to the product are aware of the risk of burns.
The electrically operated Robe Warmer must not be completely covered for safety reasons.

This instruction leaflet is an integral part of the appliance. The installer MUST ensure it is left with the end user.
All repair and maintenance activities must be performed by suitably qualified personnel.

GENERAL INFORMATION

Before assembly, please read these instructions carefully and retain for future reference.

Before proceeding with the installation, unpack the product and make sure that all the components are present, and that there is no concealed shipping damage. Components include:

• robe warmer
• instruction manual
• accessories/mounting kit

This robe warmer is designed to work at an uncovered temperature of approximately 45º°C and a covered temperature of 60º°C to 65º°C in an ambient room temperature of 20 °C.
The product is suitable for use in Zone 2 & 3 in bathrooms and kitchens and due to the low wattage is very economical to run.

The manufacturer accepts no responsibility, either contractual or for consequential loss, for any damage caused to persons, animals of property as a result of incorrect installation, alteration, maintenance or improper use.

To ensure that the installation is carried out correctly and that the unit will perform as designed, carefully follow the instructions in this manual. Failure to follow the instructions can not only cause malfunctions of the appliance but will also invalidate the warranty and hence PG shall not respond for any damage to persons, animals or property.

INSTALLATION – HANGING THE TOWEL WARMER

Ensure there is no electrical wiring, telephone cables, water pipes, or gas pipes beneath the surface where you intend to locate the towel warmer. Ensure also that the wall is strong enough to hold the towel warmer and that the desired position for the towel warmer is close enough so that the power cable will reach the power supply.

WARNING: In order to avoid a hazard for very young children, this appliance must be installed so that the lowest heated rail is at least 600 mm above the floor in accordance with (IEC 60335-2-43/A1:2006)

Please check that you have all the wall bracket fitting components as detailed below and in **Fig 1:

** 2 x wall plugs
2 x M4,5x 40 screws
1 x M5 Allen key

Step 1
Remove the cover from the double-sided tape on each of the 2 wall brackets **(Fig 2).

Step 2
Holding the robe warmer at a 30-degree angle, place the rail on the wall so only the top edge of the top 2 brackets touch the wall (Fig 3 ).

** It is recommended to use a spirit level to ensure the rail is level. Once you have the robe warmer in the correct position push the robe warmer firmly against the wall so the taped brackets are firmly stuck to the wall. Now loosen the grub screws on the brackets and remove the rail leaving the wall plates stuck to the wall.

Step 3
Using a pencil mark the center of the hole in the wall plates **(Fig 4).

** Pull the wall plates off the wall, drill the holes, insert the wall plugs and screw the wall plates onto the wall using the long M4.5 x 40 screws. It is recommended that silicon is put around the wall plug hole to ensure there is no water intrusion into the wall.

Step 4
Now slide the robe warmer bracket legs over the wall plates and using the M5 Allen key secure the rail in position with the grub screws **(Fig 5).

**

ELECTRICAL CONNECTION

When fitting in a toilet or bathroom, the installation must be in accordance with current Local and National Electrical Installation Regulations and the electrical connection must be protected by a 30mA RCD. For further information see table below:

SCYLLA

Model| Cable and plug
Power| 30 W
Supply| 220 – 240 V 50 – 60 Hz
IP| IP 21
Size| 1320 x 32 x 100 mm

OPERATING INSTRUCTIONS

The robe warmer power feed isolation switch is switched ON and OFF by pressing the switch on the bottom right hand upright (Fig 6).
o = OFF
I = ON **

ON/OFF switch
**

To operate the robe warmer, switch the red power feed button to “ I “ . The heater can now be switched on by pressing the ON/OFF switch on the timer control panel on the front of the robe warmer. The heater will remain on until the ON/ OFF button is switched off.

To use the 2-4 hour timer, switch the ON/OFF button 1 to “ON” , then press the 2-4 hour timer button 2 . Press once for 2 hours or twice for 4 hours. A small blue light 3 under the 2 or 4 hour indicator will light up to confirm the time you have chosen. The robe warmer will now remain on until the time selected has passed, then rail will then automatically switch off. The rail can be switched off at any time by pressing the ON/OFF switch.

1. ON/OFF button
2. Button for 2-4 hour timer
3. Indicator light for 2-4 hour timer

Fig 7 Timer control panel

CLEANING

Any hard scrubbing or scratching to the product surface will result in damage to the surface of the robe warmer. The use of any cleaning products which contain acid or corrosive agents will also damage this product. For best results use a cream cleaner.

Cleaning should be done using a damp soft cloth.

END OF LIFE DISPOSAL

Products with the crossed out wheelie bin symbol cannot be disposed of as household waste. Old electrical and electronic equipment must be recycled at a facility capable of handling these products and their waste by-products. If you are purchasing replacement equipment your retailer may offer a take back scheme, or be able to give details of the nearest approves authorized treatment facility. Proper recycling and waste disposal will help conserve resources while preventing detrimental effects on our health and the environment.

MANUFACTURER’S GUARANTEE

WHAT THE GUARANTEE COVERS

• This guarantee covers defects in manufacture, materials or workmanship.
• This product is supplied for installation in homes.
• For a period of 5 years from the date of purchase our only obligation is to replace the defective non-electrical components of products at our discretion. Replaced products become our property and can only be disposed of with our authorisation.
• Electrical elements are guaranteed for 24 months from the date of purchase.
• Please inspect your product on receipt. In the unlikely event a product problem is noted prior to installation, you must refer back to us within 30 days. In the event of shipping damage you must refer back within 14 days. We cannot accept any claim outside this timeframe.
• Any claim made to us must be in writing and accompanied by a proof of payment showing the date of purchase.
• Should the product be deemed to be unsuitable through no fault of the manufacturer, the purchaser can return the product for a refund within 28 days, however the purchaser is responsible for the safe return of the product and any shipping cost.

WHAT THE GUARANTEE DOES NOT COVER

• General wear and tear.
• Damage arising from improper use or installation.
• Damage resulting from failure to maintain the product in accordance with the cleaning and care instructions quoted below.
• Damage arising due to connecting the product to an electrical supply not corresponding with the name plate specifications, or due to power surges.
• Damage arising from installation not in accordance with electrical or plumbing codes, or use of accessories not approved by the manufacturer.
• No liability is accepted for any injury, loss of income, consequential damage to other household fixtures, fittings or furnishings arising from any claim, even if attached to the product.
• No liability is accepted for any labour or associated costs that may be incurred in the removal or installation of the product.
• Any freight charges, damages due to loss or damage in transit.
• Our obligation under this warranty is to the original purchaser only and may not be transferred if the product is sold to another party.
• As we are continually improving and developing our ranges we may not be able to provide an identical replacement for a defective product through the warranty period. Where an identical product is not available, we will supply a product of a value and such features as we consider appropriate in the circumstances.
• The replacement product will be covered under this warranty only for the balance of the original warranty period.
• This warranty does not affect your statutory rights. If any of the provisions above are contrary to any relevant legislation, then that provision shall be deemed to be excluded from the warranty and the rest of the provisions will apply.

This product should only be installed by a qualified professional. Keep this warranty sheet along with your sales receipt together for future reference (electronic sales receipt acceptable). You must provide proof of payment to invoke this warranty. If you have any warranty claims contact the retailer you purchased this item from.

0000000000001_PG_MANUAL_Scylla-Exposed-Cable_2022-04-01_GB_NA_000000_01

A PURMO GROUP BRAND
Bulevardi 46
P.O. Box 115
FI-00121 Helsinki
Finland
www.purmogroup.com

Every care has been taken in the creation of this document. No part of this document may be reproduced without the express written consent of Purmo Group. Purmo Group accepts no responsibility for any inaccuracies or consequences arising from the use or misuse of the information contained herein.

References

• Purmo Group - Complete solutions in heating and cooling

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>