B HOME HZ4150 Adjustable Bed User Guide

B HOME HZ4150 Adjustable Bed

Product Specifications

• Product Size:
  • Twin XL : 38 x 80 (96.5 x 203 cm)
  • Split Queen: 30 x 80 (76 x 203 cm)
  • Full : 54 x 75 (137 x 190.5 cm)
  • Queen: 60 x 80 (152 x 203 cm)

Product Usage Instructions

Safety Precautions
Thank you for purchasing the Homezone zero-clearance adjustable bed. Please read all directions before using the bed and retain this guide for reference.

Input voltage: AC 100-240V, 50/60HZ, output: DC29V 2.0A.

• Unplug the bed before cleaning it.
• Keep the product wire, power supply, and control box away from heat.
• Do not use the bed in a humid environment.
• The connector part of the wire and the gap between the motor and the control box cannot be exposed to liquid or high humidity.
• Never operate the bed if it has a damaged cord or plug, or is not working properly.
• Unplug the power cord and remove the remote control battery when the bed is not being used for a prolonged period.
• Consult your physician if you have any health questions regarding the use of this product.
• Do not let children play with or operate the bed.
• Do not allow children or pets underneath the bed.

Assembly

1. Lay the carton flat on the floor and carefully cut it open.
2. Lift the carton so that the open side faces down and slide it up and off the bed. Place the bed upside-down flat on the floor.
3. Remove and discard the plastic bag. Put together the two pieces of the bed and align them flat on the floor.
4. Cut the zip ties, take out all the part boxes and the mattress rail, and check that you have all the necessary parts according to the parts list.
5. For leg assembly push the screw through the triangular brace. Screw in the leg and tighten. Leg height adjustments: 6”+3”+3”.
6. Insert batteries into the remote control. Press the first circled button. If the motor begins to run, unplug the power supply and turn the bed over to its right-side-up position. If the motor does not run, it needs to re-match its code.
7. Connect the wire (on the bed) to the jack of the power supply box. Connect the AC power cable to the other jack on the power supply box. Connect the AC power cable to your nearby power outlet.
8. Insert the mattress rail at the foot of the bed. Then, the bed is ready for use.

Remote Control and Functions

• Locking key
• Position Memory
• Zero Gravity Position
• Foot Up
• Sleeping Position
• Massage Time lights Backrest Massage Massage On/Off

Safety Precautions

Thank you for purchasing the Homezone zero-clearance adjustable bed.

Please read all directions before using the bed, and retain this guide for reference.

• Input voltage: AC 100-240V. 50/60HZ, output: DC29V 2.0A.
• Unplug the bed before cleaning it.
• Keep the product wire, power supply, and control box away from heat.
• Do not use the bed in a humid environment. The connector part of the wire and the gap between the motor and the control box cannot be exposed to liquid or high humidity.
• Never operate the bed if it has a damaged cord or plug, or is not working properly.
• Unplug the power cord and remove the remote control battery when the bed is not being used for a prolonged period.
• Consult your physician if you have any health questions regarding the use of this product. Do not let children play with or operate the bed.
• Do not allow children or pets underneath the bed.

Product Specifications

Product Size:

• Twin XL: 38” x 80” (96.5 x 203 cm)
• Full: 54” x 75” ( 137 x 190.5 cm)
• Split Queen: 30” x 80” (76 x 203 cm)
• Queen: 60” x 80”(152 x 203 cm)

Assembly

1. Lay the carton flat on the floor and carefully cut it open.

2. Lift the carton so that the open side faces down and slide it up and off the bed. Place the bed upside-down flat on the floor.

3. Remove and discard the plastic bag. Put together the two pieces of the bed and align them flat on the floor.

4. Cut the zip ties, take out all the part boxes and the mattress rail, and check that you have all the necessary parts according to the parts list.

5. For leg assembly push the screw through the triangular brace.Screw in the leg and tighten, Leg height adjustments: 6’’+3’’+3’

6. Connect the wire (on the bed) to the jack of the power supply box Connect the AC power cable to the other jack on the power supply box. Connect the AC power cable to your nearby power outlet.

7. Insert batteries into the remote control. Press the first circled button.
   If the motor begins to run, unplug the power supply and turn the bed over to its right-side-up position.
   If the motor does not run, it needs to re-match its code.
   Matching code:
   Method1: Cut off the power and wait for 10 seconds. Then plug the power again.
   You will see the arrow points to light up the blue light(like the circle shown in the first picture). At the same time, the LED lights will flash. Then press and hold the “PAIR” button on the remote control(like in the third picture). This step must be done in 10 seconds when the LED lights flash. Release them when the white backlight flashes. Finally, if the blue light in the controller turns to green and the LED lights go out, the code matches.
   Method2: Press twice the controller button that the arrow points to light up the blue light(like the circle shown in the first picture). At the same time, the LED lights will flash.
   Then press and hold the “PAIR” button on the remote control(like in the third picture). Release them when the white backlight flashes. Finally, if the blue light in the controller turns to green and the LED lights go out, the code matches.

8. Insert the mattress rail at the foot of the bed. Then the bed is ready for use.

Remote Control and Functions

Memory Setting
Setting a memory position if you’re not satisfied with the factory setting.

1. Press the FLAT button the flatten the bed .
2. Adjust the bed to your preferred position by pressing the head and foot up/down buttons
3. Press and hold button M and let go after you hear a “didi” sound that indicates the setting has been Successfully programmed

Bluetooth APP

1. IOS version 8.0 or above

2. Searching for OkinComfortableBed‖in App Stores or scan the QR to download the APP

3. Open the APP and select the number of Motors. 2M-2 motors/3M-3 motors/4M-4 motors.
   This product is 2 motors, so select 2M

4. After selecting in, click the gear to select the Bluetooth you want to connect. Position: lift or lower different bed parts
   Memory: ZG position;TV/PC position;Lounge position;M position

Troubleshooting

If you experience problems with your adjustable bed, please follow these steps:

1. Press any button on the remote controller to see whether the blue backlight is bright. If it is dim or does not light, check the batteries. Replace batteries when necessary
2. Check the green power indicator light on the power supply. If it is not lighted, check the power outlet.
3. Check for loose wires and connectors.
4. Check if the adjustable bed is assembled according to above steps.
   If your problems cannot be solved by above steps, please contact us.

FAQ

• Q: Can children operate this adjustable bed?
  • A: No, children should not play with or operate this bed for safety reasons.
• Q: How do I clean this adjustable bed?
  • A: Unplug the bed before cleaning it, and do not expose any part to liquid or high humidity.\

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>