VOLLRATH 39732 Cafeteria Breath Guard Installation Guide
- August 14, 2024
- VOLLRATH
Table of Contents
VOLLRATH 39732 Cafeteria Breath Guard
Specifications:
- Brand : Vollrath
- Model : Cafeteria Breath Guard
- Types Available : One Piece, Three Piece
- Material : Plastic
- Item No.: 2350030-01
Product Usage Instructions
One Piece Breath Guard Installation:
Install the breath guard uprights (A) to the studs (B) securing with cap nuts
(C) as shown in Figure 1. Repeat for all four uprights.
Three-Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three-Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations
The Vollrath Company, L.L.C.
- 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX : 800.752.5620
Vollrath of Canada, Co.
- Tel : 800.695.8560
- FAX : 800.752.5620
© 2010 The Vollrath Company, L.L.C.
FAQ
Q: What should I do if I accidentally over-tighten the cap nuts?
A: If you accidentally over-tighten the cap nuts and notice cracking in the
plastic, stop immediately and contact Vollrath customer service for
assistance.
Q: Can the breath guards be easily removed for cleaning?
A: Yes, the breath guards can be easily removed for cleaning by following the
installation steps in reverse order.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>