Axolight USAU45-2XXXXE26 Ceiling Light Fixture Instructions

Axolight USAU45-2XXXXE26 Ceiling Light Fixture

Product Specifications:

• Maximum Height: 260 cm
• Diameter: 47 cm
• Light Bulb Type: 2 x E26 150W

Product Usage Instructions

Preparation

1. Ensure the ceiling where the fitting will be installed can support the weight.
2. Disconnect all electrical power to the area before starting installation.

Installation Steps

1. Remove all glass components (labeled C-B-A) and the light bulb.
2. Unscrew all components (labeled 3) and remove component 2. Verify that component 8 is securely fixed.
3. Fix component 1 to the ceiling using appropriate screws.
4. Insert component 8 through components 6 and 9 to secure component 2 to component 1 as per the diagram.
5. Make a suitable electrical connection.
6. Adjust the length of component 7 with component 5.
7. Attach component 2 to component 1 with all components 3.
8. Insert the glass components in sequence A-B-C into components4, screwing them securely.

Frequently Asked Questions (FAQ)

• Q: What is the maximum wattage and type of light bulb recommended for use?
  

  • A: Use a maximum of 2 x E26 150W Type T light bulbs.

“`

GENERAL INSTRUCTIONS FOR INSTALLING ALL LIGHTS

LIGHTS MUST ONLY

BE INSTALLED BY QUALIFIED PERSONNEL WHO MUST FOLLOW ALL INSTRUCTIONS SUPPLIED TOGETHER WITH CURRENT CODES AND REGULATIONS
FOR ELECTRICAL AND LIGHTING SYSTEMS
THE SAFETY GUARANTEE FOR THE DEVICE IS ONLY VALID IF ALL

THE INSTRUCTION SHEETS SUPPLIED WITH THE DEVICE ARE FOLLOWED AND KEPT

• ON RECEIPT OF GOODS, ENSURE THAT THE PACKAGING IS UNDAMAGED, COMPLETE AND SEALED WITH AAO LIGHT ADHESIVE TAPE, WITHOUT ANY EVIDENCE OF TAMPERING. IF THIS IS NOT THE CASE, SEND A FAA OR E-MAIL ACCORDING TO THE CONDITIONS OF SALE AGREED WITH THE RETAILER
• IF, ON OPENING THE PACKAGING, THERE ARE NO INSTRUCTIONS YOU MUST REQUEST THESE FROM THE RETAILER OR MANUFACTURER BEFORE INSTALLING THE DEVICE
• READ TECHNICAL INFORMATION SHOWN ON LABELS ATTACHED TO THE LIGHT CAREFULLY. IF, ON OPENING THE PACKAGING, THESE LABELS ARE MISSING, YOU MUST REQUEST THESE FROM THE RETAILER OR MANUFACTURER BEFORE INSTALLING THE DEVICE
• CHECK THAT THE SURFACE AND ENVIRONMENT WHERE THE LIGHT WILL BE INSTALLED AND USED ARE SUITABLE
• CHECK THAT THE LIGHTING CIRCUIT HAS AN ADEQUATE SAFETY SYSTEM
• BEFORE ANY INSTALLATION, MAINTENANCE, CLEANING OR CHANGING BULBS, ENSURE THAT THE LIGHTING CIRCUIT IS FREE OF ELECTRICAL CURRENT (IS DEACTIVATED) AND THAT THE LIGHT COMPONENTS ARE COMPLETELY COOL ( -20″C)
• THE LIGHT SHOULD IN NO WAY BE: TAMPERED, ALTERED OR USED FOR PURPOSES OTHER THAN THAT FOR WHICH IT WAS MANUFACTURED
  • THIS SYMBOL INDICATES THAT THE DEVICE MUST BE COLLECTED AND DISPOSED OF VIA DIFFERENTIATED WASTE COLLECTION AT THE END OF ITS LIFE IN A SUITABLE DIFFERENTIATED WASTE COLLECTION CENTRE
  • IF PRESENT, THIS SYMBOL INDICATES THE MINIMUM DISTANCE IN METRES AT WHICH THE LIT OBJECT MUST BE POSITIONED
  • IF PRESENT, THESE SYMBOLS INDICATE THAT THE GLASS MUST BE SUBSTITUTED IMMEDIATELY IF BROKEN
• TO AVOID BURNS OR ACCIDENTAL INJURY OF ANY KIND, AVOID TOUCHING DEVICES WHEN IN USE WITH ANY PART OF THE BODY OR ANY OTHER OBJECT, IF NOT SPECIFICALLY INDICATED• IF NECESSARY ASK TO MO LIGHT FOR A BOROSILICATE SPARE PART, WHERE PRESENT
• IN ORDER TO IMPROVE THE LIFE, SAFETY AND EFFICIENCY OF THE LIGHT, REGULAR MAINTENANCE MUST BE CARRIED OUT BY QUALIFIED PERSONNEL WHO SHOULD ALSO CHECK THAT CABLE FITTINGS AND SCREWS ARE TIGHTENED, THAT THE CLOSURE OR LOCKS OF ANY THREADED PARTS ARE SECURE AND THAT THE BULB OR THE L.E.D. ARE WORKING PROPERLY. REGULAR MAINTENANCE EVERY SIX MONTHS IS ADVISABLE AND THAT THE BULB OR THE L.E.D. ARE WORKING PROPERLY. REGULAR MAINTENANCE EVERY SIX MONTHS IS ADVISABLE
• DO NOT USE SOLVENTS, ALCOHOL OR ABRASIVE DETERGEN­TS TO CLEAN THE DEVICE
• AVOID CONTACT WITH FIRE OR INCANDESCENT MATERIAL • AAO LIGHT WILL NOT BE HELD RESPONSIBLE IF ALL INSTRUCTIONS FOR INSTALLATION AND ASSEMBLY SUPPLIED OR REQUESTED ARE NOT OBSERVED, OR IF AAO LIGHT PRODUCTS ARE USED FOR UNSUITABLE PURPOSES• CLASS I AND II LUMINAIRES IN WICH CODE THERE IS THE ’12V’ ABBREVIATION, ARE FOR 220-240V FUNCTIONING AND THE LAMPS ARE FOR 12V
• DO NOT TOUCH THE L.E.D. SURFACE, WHETHER SWITCHED ON OR OFF
• DO NOT DIRECTLY LOOK AT THE SWITCHED ON L.E.D. SOURCE
• THE MANUFACTU­RER MAY MAKE ANY TYPE OF MODIFICATION TO EQUIPMENT OR INSTRUCTIONS WITHOUT PRIOR NOTICE
• COLOURS AND SIZES MAY VARY FROM ONE LOT TO ANOTHER
• IF PRESENT, ISOLATE THE DIMMING WIRES WHEN UNUSED
• POSSIBLE ERRORS COULD OCCUR DURING THE PRINTING PROCESS
• THE LIGHT SOURCE CONTAINED IN MO LIGHT BUILT-IN LED LUMINAIRES SHALL ONLY BE REPLACED BY THE MANUFACTURER OR HIS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON
• RSN. IF PRESENT, THIS INITIALS: IF THE FLEXIBLE CABLE OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE WXCLUSIVELY REPLACED BY THE MANUFACTURER ASSISTANCE SERVICE OR A SIMILAR TECHNICAL ASSISTANCE IN ORDER TO AVOID A HAZARD, FOR INFORMATION ON HOW TO ASSIST AND REPAIR CONTACT AAOLIGHT CUSTOMER CARE, FOR STORAGE AND TRANSPORT USE THE ORIGINAL PACKAGING.

INSTALLATION INSTRUCTION

• NNSSUURREE TTHHAATT TTHHEE CCEEIILLIINNGG WWHHEERREE TTHHEE FFIITTTTIINNGG IISS BBEEIINNGG IINNSSTTAALLLLEEDD IISS SSUUIITTAABBLLEE FFOORR IITT AND
• SUPPORTS ITS WEIGHT-FIX THE COMPONENTS(1) TO THE CEILING WITH SUITABLE SCREWS-INSERT THE COMPONENT (8) THROUGH THE
• COMPONENTS (6+9) FOR BLOCK THE COMPONENT(2) TO THE COMPONENT (1)
• LIKE SKETCH-MAKE A SUITABLE ELECTRICAL CONNECTION ADJUST ADEQUATELY THE MEASUREMENT OF THE COMPONENTS(11) BY COMPONENT(5)-FIX THE COMPONENT (2) TO
• THE COMPONENT(1) WITH ALL THE COMPONENTS(3)-INSERT THE GLASSES WITH SEQUENCE (A-B-C) IN THE COMPONENTS (4) SCREWING WELL.

MODEL USAU45/2XXXXE

• (GB) INSPECTING ELECTRICAL WIRES IN THE J-BOX:
• REMOVE ALL THE GLASS (C-B-A) AND THE LIGHT BULB-
• UNSCREW ALL THE COMPONENTS (3) AND REMOVE
• COMPONENT (2) VERIFYING THE COMPONENT(8) IS WELL FIXED
• TO THE COMPONENTS (1-2) AND INSPECT THE ELECTRICAL WIRES- REPLACE ALL THE COMPONENTS.

INDEPENDENTLY OF AN OUTLET BOX.

• REMOVE COVER BEFORE USING UNIT
• ELIMINER LA PROTECTION AVANT USAGE

TECHNICAL DATA

• SIZE: H .max 260 cm, D .47 cm.
• BULBS : USE / UTILISER MAX 2 x E26 150 W TYPE T

THIS LUMINAIRE MUST BE MOUNTED OR SUPPORTED INDEPENDENTLY OF AN OUTLET BOX.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>