GRANDJOY W-27V Roman Waterfall Bathtub Faucet Instruction Manual
- June 1, 2024
- GRANDJOY
Table of Contents
GRANDJOY W-27V Roman Waterfall Bathtub Faucet
Instruction Manual Bathtub faucet System
Warranty Duration
All parts of this faucet system are warranted to the original purchaser to be free from defects in material and workmanship for a lifetime.
Repair and Replacement
If the product has defects in material and workmanship within the warranty period, we will repair or replace the product free of charge. However, you may be required to provide the invoice when requesting repairs or replacement from us.
Exclusions
We shall not be responsible for the following cases:
- Damage to the product caused by improper installation,misuse, unauthorized repair or replacement,or abuse(including damage during shipment).
- Damage to the product caused by improper dismantlement after installation.
- Damage resulting from abnormal water pressure and impurities in water pipes is not covered under this warranty.
- Rust on the product due to insufficient care and maintenance is not covered under this warranty.
- Damage caused by natural disasters such as fire, flood, earthquake, electric storms, etc., is not covered under this warranty. I hope this helps! If you have any further questions or concerns, please let me know.
Having Trouble?
Contact us. Email: info@faucetsupport.com &
Toll Free: 1-888-969-6880
Installation Condition
- Check the accessories list to verify that all parts are complete in this package.
- Do not disassemble the mainbody by yourself.
- Connect inlet pipes to supply valves.
- Make sure inlet pipes and supply valves have benn installed and cleaned, with no impurities in the pipeline.
- After installation, check all joints for leakages.
- Do not leave the rain shower system exposed to a severely corrosive environment.
VOII MAY NEED
Basin Faucet Standard part List
Accessories List
Bathtub Faucet Installation
-
Step 1
Connect Brass Part 4 to Faucet Body I and insert Brass Part 4 through the basin hole. Install Faucet Body Gasket 5 and Mounting Nut X in sequence, and then tighten the nut with a wrench. Next, insert Tee Gasket 6 into Tee 9 and connect Tee 9 to Brass Part 4.
-
Step 2
Remove the Decorative Seats 3 and place them on the basin holes. From the underside of the basin holes, connect the Control Water Bodies 8 to the Decorative Seats 3 and tighten them. Finally, install the Handles 2 and tighten them. (Note: Do not attempt to disassemble the valve yourself, as this may cause leakage.) -
Step 3
Connect one side of the Inlet Hoses 11 to the Control Water Bodies ® and the other side to Tee 9, then tighten them. Note that the red hose is for hot water and the blue hose is for cold water
-
Step 4
Connect two additional inlet hoses (please buy them by yourself) to the angle valves and control water bodies. Connect the hose on the left to the hot water and the hose on the right to the cold water.
Basin Faucet Standard part List-Model: B
Accessories List
-
Step 1
Connect Brass Part 4 to Faucet Body D and insert Brass Part 4 through the basin hole. Install Faucet Body Gasket 5 and Mounting Nut in sequence, then tighten the nut with a wrench. -
Sten 2
-
Remove the Decorative Seats (3 and place them in the bathtub holes.
-
From the underside of the bathtub holes, connect Transforms Control Valve ® and Control Water Bodies 9 to the Decorative Seats 3 and tighten them. Then install the Handles 2 and tighten them.
-
For Hand Pedestal 10 installation: Remove Pedestal Gaskets 12 and Mounting Nut 13. Connect them to Hand Pedestal 10 from the underside of the bathtub holes, then tighten Mounting Nut 13 with a wrench. (Note: Do not attempt to disassemble the valve yourself, as this may cause leakage.) The left Control Water Body 9 connects to the hot water, while the right one connects to the cold water.
-
Sten 3
linstall the hot and cold hoses (17) according to the above drawings. Connect one side of the hot and cold hoses (17) to the transforms control valve (9) and the other side to the control water bodies(8). The left side is for hot water, and the right side is for cold water. One end of the shower hose (14) should be connected to the hand shower (10), while the other end should be connected to the shower connect hose (14) through the hand pedestal (0). Then, connect the other end of the shower connect hose (14) to the transforms control valve (9). Finally, connect one end of the body connect hose (15) with brass part (4) and the other end to the transformscontrol valve (9), then tighten them. Separately, connect another two inlet hoses (please buy them yourself) to the angle valves and control water bodies (8).
Do’s
- In order to keep the mixer surface bright, please clean the mixer regularly.
- Rinse the faucet with clean water and wipe it with a soft cotton cloth.
- Use one of the following cleaners to remove dirt from the surface:
- Mild liquid cleaner.
- Colorless glass cleaner and powder cleaner that do not cause abrasion and can be dissolved completely.
- Polish liquid that does not cause abrasion.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>