Mission Air LEO WIFI Regulator Temperatury Instruction Manual

August 9, 2024
Mission Air

Mission Air LEO WIFI Regulator Temperatury

Mission-Air-LEO-WIFI-Regulator-Temperatury

Product Overview

Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-1

  • Voltage (V) 220-230, 50-60Hz
  • Power consumption (W) <1,5
  • Accuracy (℃) -0,5
  • Sensor +/ NTC
  • Protection class IP20
  • Current intensity (A) NTC 16
  • Setting range (℃) 5-45
  • Ambient temperature (℃)  -5-45

FUNCTIONS

Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-2

CONTROL

Power supply: on/off

Control selection: by pressing this button you switch between manual and programmable mode.

  Clock : press to set the current time. Pressing the button takes you to the next setting (minutes >> hours>> days of the week), the values are set with the arrows, after 10s of inactivity the settings are automatically saved. Pressing the button a fourth time will take you to the weekly schedule programming mode settings.

Arrows : used to increase or decrease values in many functions.

  Programming mode: press the clock button 4 times.

  • The icon corresponding to one of the six ranges described in the ‘Functions’ section appears on the left-hand side of the display.
  • The days of the week for which you are setting the programme appear above:
    • MON, TUE, WED, THU, FRI – days from Monday to Friday
    • SAT – Saturday
    • SUN – Sunday
  • Data is entered for consecutive ranges in the following order: activation time of the respective range >> temperature
  • Use the arrows to change the relevant value and the button to move to the next parameter/range.
  • First set the values of the 6 ranges for Mon to Fri and then the same for Sat and Sun.
  • After 10s of inactivity, the settings will be automatically saved.

ATTENTION : The time values of the next period must not be lower than those of the previous period. The set schedule for a given range must be within the time interval 00:00-24:00. A given schedule cannot switch to the next day!

SAMPLE WORK SCHEDULE

Mission-Air-LEO-WIFI-Regulator-Temperatury-table-1

ADVANCED SETTINGS

When the unit is switched off, hold down the clock and power buttons simultaneously for 5s to access the advanced settings of thecontroller. Use the arrows to change the values, and the key move to the next parameter. The changes made will be saved when the power button is pressed.

Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-10

MONTAGE

The product is suitable for installation in a standard 86mm electrical box.

  1. Make the electrical connection of the controller,
  2. Screw the panel to the mounting box,
  3. Connect the LCD screen to the panel,
  4. End of process.

Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-11

Caution : The appliance may only be installed by a qualified electrician, who will certify the correctness of the installation with an entry in the guarantee card of the controller or heating system. Otherwise, the product loses its manufacturer’s warranty protection!

Risk of electrocution!
Disconnect the power source before connecting wires. Contact with live internal components of the unit can cause electrocution, which can lead to serious injury or even death.

WIRING DIAGRAM

Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-12

  • A – for electric underfloor heating
  • B – for water heaters
  • C – for gas boilers and water underfloor heating

WIFI CONFIGURATION

Follow the instructions below to connect your smartphone or tablet to the controller via WiFi.
Attention! The following guidance is for information purposes and is current at the time of development. Due to the continuous development of applications and software, this process and the appearance of the application or individual functions may vary in the future.

  1. Download and install the TUYA SMART or SMART LIFE mobile app on your smartphone or tablet and register.Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-14
  2. Select the ‘+’ option in the top right corner to add a new device. Then select the ‘Small devices’ tab and ‘Thermostat’ from the list.
  3. Select the appropriate WiFinetwork and enter the password to access it.
  4. On the switched-off display, hold down the down arrow for approx.8s. until the WiFi icon starts flashing on the display.
  5. Confirm that the WiFi icon isflashing on the controller screen.Mission-Air-LEO-WIFI-Regulator-Temperatury-fig-15
  6. The device has been successfully added. At this stage, you can change the name of the controller, which will be visible in the application.
  7. Main screen to control the operation of the unit.
  8. View of the tab for setting the weekly schedule.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals