Shelly Qubino Wave Pro 2PM Relay Switch with Power Metering User Guide

Shelly Qubino Wave Pro 2PM Relay Switch with Power Metering

Specifications

• Power supply: 110-240 V AC, 50/60 Hz
• Power consumption: < 0.3 W
• Max. switching voltage AC: 240 V
• Max. switching current AC: 16 A per channel, 25 A total
• CPU: 868.4 MHz
• Maximum radio frequency power transmitted in frequency band(s): < 25 mW

Product Usage Instructions

Installation Instructions
The Wave Pro 2 PM is a DIN rail mountable 2-channel smart switch with power measurement. Follow the steps below for installation:

1. The Device can be DIN-mounted inside the breaker box.
2. Refer to the wiring scheme in the user guide for detailed installation instructions.

Operational Instructions

Supported Load Types:

• Resistive (incandescent bulbs, heating devices)
• Capacitive (capacitor banks, electronic equipment, motor start capacitors)
• Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)

Important Disclaimer

• Ordering Code: QPSW-0A2P16EU

User and Safety Guide
This document contains important technical and safety information about the Device, its safe use, and installation. Read before use.

Frequently Asked Questions (FAQ)

• Q: Can the Wave Pro 2 PM be used with switches and push buttons?
  A: Yes, the Device is compatible with switches (default) and push buttons.

• Q: What is the maximum load capacity of the Wave Pro 2 PM?
  A: The Device can handle a load of up to 16 A per channel (25 A in total).

• Q: Where can I find more detailed installation instructions?
  A: For more detailed installation instructions, refer to the extended user guide at Wave Pro 2PM Extended User Guide.

2-circuit DIN-mountable Z-Wave® smart switch with power measurement

LEGEND

• Device terminals:
  • N: Neutral terminal
  • L: Live terminal (110–240 V AC)
  • SW (SW1): Switch/push-button input terminal (controlling O (O1))
  • SW2: Switch/push-button input terminal (controlling O2)
  • I1: Load circuit 1 input terminal
  • I2: Load circuit 2 input terminal
  • O (O1): Load circuit 1 output terminal
  • O2: Load circuit 2 output terminal
• Wires:
  • N: Neutral wire
  • L: Live wire (110-240 V AC)
• Button:
  • S: S button

READ BEFORE USE
This document contains important technical and safety information about the Device, its safe use and installation.

CAUTION!
Before beginning the installation, please read carefully and entirely this guide carefully and any other documents accompanying the Device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law, or refusal of legal and/or commercial guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure to follow the user and safety instructions in this guide.

TERMINOLOGY

• Gateway – A Z-Wave® gateway, also referred to as a Z-Wave® controller, Z-Wave® main controller, Z-Wave® primary controller, or Z-Wave® hub, etc., is a device that serves as a central hub for a Z-Wave® smart home network. The term “gateway” is used in this document.
• S button – The Z-Wave® Service button, which is located on Z-Wave® devices and is used for various functions such as inclusion (adding), exclusion (removing), and resetting the device to its factory default settings. The term “S button” is used in this document.
• Device – In this document, the term “Device” is used to refer to the Shelly Qubino device that is a subject of this guide.

ABOUT SHELLY QUBINO

Shelly Qubino is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits with a smartphone, tablet, PC, or home automation system. They work on Z-Wave® wireless communication protocol, using a gateway, which is required for the configuration of devices. When the gateway is connected to the internet, you can control Shelly Qubino devices remotely from anywhere. Shelly Qubino devices can be operated in any Z-Wave® network with other Z-Wave® certified devices from other manufacturers. All mains-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network. Devices are designed to work with older generations of Z-Wave® devices and gateways.

WAVE PRO SERIES
Wave Pro series is a line of devices suitable for homes, offices, retail stores, manufacturing facilities, and other buildings. Pro devices are DIN- mountable inside the breaker box, and highly suitable for new building construction. All Wave Pro devices can be controlled and monitored through the Z-Wave® network.

ABOUT THE DEVICE
The Device is a DIN rail mountable 2-channel smart switch with power measurement. It controls the on/off function for two independent electrical devices with a load of up to 16 A per channel (25 A in total). It is compatible with switches (default) and push buttons.

INSTALLATION INSTRUCTIONS

The Device can be DIN-mounted inside the breaker box.

For the installation instructions, refer to the wiring scheme (Fig. 1) in this user guide.

• CAUTION! Danger of electrocution. Mounting/installation of the Device to the power grid has to be performed with caution, by a qualified electrician.
• WARNING! Danger of electrocution. Every change in theconnections has to be done after ensuring there is no voltage present at the Device terminals.
• CAUTION! Use the Device only with a power grid and appliances that comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage it.
• CAUTION! Do not connect the Device to appliances exceeding the given max. load!
• CAUTION! Allow at least 10 mm of space around each Pro device if you expect currents higher than 5 A per channel.
• CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
• CAUTION! Do not install the Device where it can get wet.
• CAUTION! Do not use the Device if it has been damaged!
• CAUTION! Do not attempt to service or repair the device yourself!
• CAUTION! Before starting the mounting/installation of the Device, check that the breakers are turned off and there is no voltage on their terminals. This can be done with a mains voltage tester or multimeter. When you are sure that there is no voltage, you can proceed to connect the wires.
• CAUTION! Do not shorten the antenna.
• RECOMMENDATION: Place the antenna as far away aspossible from metal elements as they can cause signal interference.
• RECOMMENDATION: Connect the Device using solid single-core cables or stranded cables with ferrules. The cables should have insulation with increased heat resistance, not less than PVC T105°C (221°F).
• RECOMMENDATION: For inductive appliances that cause voltage spikes during switching on/off, such as electrical motors, fans, vacuum cleaners, and similar ones, an RC snubber (0.1 μF / 100 Ω / 1/2 W/600 V AC) should be connected parallel to the appliance.
• CAUTION! Do not allow children to play with the push buttons/switches connected to the Device. Keep the devices for remote control of Shelly Qubino (mobile phones, tablets, PCs) away from children.

EXTENDED USER GUIDE
For more detailed installation instructions, use cases, and comprehensive guidance on adding/removing the Device to/from a Z-Wave® network, factory reset, LED signalization, Z-Wave® command classes, parameters, and much more, refer to the extended user guide at: https://shelly.link/WavePro2PM-KB.

SPECIFICATIONS

• Power supply 110-240 V AC, 50/60 Hz
• Power consumption < 0.3 W
• Power measurement (W) Yes
• Max. switching voltage AC 240 V
• Max. switching current AC 16 A per channel, 25 A total
• Max. switching voltage DC N/A
• Max. switching current DC N/A
• Overheating protection Yes
• Overload protection Yes
• Overvoltage protection Yes
• Distance Up to 40 m indoors (131 ft.) (depends on local conditions)
• Z-Wave® repeater Yes
• CPU Z-Wave® S800
• Z-Wave® frequency bands 868.4 MHz
• Maximum radio frequency power transmitted in the frequency band(s) < 25 mW
• Size (H x W x D) 94 x 19 x 69 ±0.5 mm / 3.7 x 0.75 x 2.71 ±0.02 in
• Weight 75 g / 2.65 oz.
• Mounting DIN rail
• Screw terminals max. torque 0.4 Nm / 3.54 lbin
• Conductor cross-section
  • 0.5 to 2.5 mm² / 20 to 14 AWG (green connectors)
  • 0.5 to 1.5 mm² / 20 to 16 AWG (white connectors)
• Conductor stripped length
  • 6 to 7 mm / 0.24 to 0.28 in (green connectors)
  • 5 to 6 mm / 0.20 to 0.24 in (white connectors)
• Shell material Plastic
• Color Black
• Ambient temperature -20°C to 40°C / -5°F to 105°F
• Humidity 30% to 70% RH
• Max. altitude 2000 m / 6562 ft.

OPERATIONAL INSTRUCTIONS

• SW1: If the SW (SW1) is configured as a switch (default), each toggle of the switch will change the output O (O1) state to the opposite state – on, off, on, etc. If the SW (SW1) is configured as a push-button in the Device settings, each press of the push-button will change the output O (O1) state to the opposite state – on, off, on, etc.
• SW2: If the SW2 is configured as a switch (default), each toggle of the switch will change the output O2 state to the opposite state – on, off, on, etc. If the SW2 is configured as a push-button in the Device settings, each press of the push-button will change the output O2 state to the opposite state – on, off, on, etc.

SUPPORTED LOAD TYPES

• Resistive (incandescent bulbs, heating devices)
• Capacitive (capacitor banks, electronic equipment, motor start capacitors)
• Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)

IMPORTANT DISCLAIMER

Z-Wave® wireless communication may not always be 100%reliable. This Device should not be used in situations in which life and/or valuables are solely dependent on its functioning. If the Device is not recognized by your gateway or appears incorrectly, you may need to change the Device type manually and ensure that your gateway supports Z-Wave Plus® multi-channel devices.

• ORDERING CODE: QPSW-0A2P16EU

DECLARATION OF CONFORMITY

Hereby, Shelly Europe Ltd. declares that the radio equipment type Wave Pro 2PM complies with Directive 2014/53/ EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://shelly.link/WavePro2PM-DoC.

For the UP PSTI Act Statement of Compliance scan the QR code

MANUFACTURER
Shelly Europe Ltd.

• Address: 103 Cherni Vrah Blvd., 1407 Sofia, Bulgaria
• Tel.: +359 2 988 7435
• E-mail: zwave-shelly@shelly.cloud
• Support: https://support.shelly.cloud/
• Web: https://www.shelly.com.

Changes in the contact data are published by the Manufacturer on the official website.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>