RENAC R1 Moto, Macro Series Solar Inverter User Manual

: August 8, 2024
: RENAC

RENAC R1 Moto, Macro Series Solar Inverter

Product Information

Specifications

Model : NAC4K-DS / NAC5K-DS / NAC6K-DS / R1-8K-DS / R1-10K-DS / R1-10K5-DS
Type : Transformerless-based inverter

Product Usage Instructions

Introduction
This manual provides detailed information on the solar inverters in the Moto & Macro Series. It is essential to read and understand the safety instructions before proceeding with the installation or operation of the inverters.
Technical Description of Inverters
The inverters in this series are transformerless based, designed for efficient solar energy conversion. They are suitable for both AC and DC installations, provided the user complies with electrical regulations.
Installation and Startup
Before installation, carefully inspect the inverter and its packaging for any damage. Ensure that the voltages of the solar modules fall within the specified limits before connecting them to the inverter. For detailed installation instructions, refer to section 3 of the user manual.
User Interface
The user interface of the inverters allows for easy monitoring and control of the solar energy conversion process. Familiarize yourself with the interface to maximize the performance of the inverters.
Warranty
The warranty details and claim procedure are outlined in this section. It is important to follow the warranty claim procedure in case of any issues with the inverters. Service after warranty expiration is also addressed.
Troubleshooting and Maintenance
This section provides guidelines for troubleshooting common issues that may arise during the operation of the inverters. Regular maintenance is crucial to ensure optimal performance.

Introduction

This manual describes solar inverters: NAC4K-DS / NAC5K-DS / NAC6K-DS / R1-8K- DS / R1-10K-DS / R1-10K5-DS. These inverters are transformerless based inverter. Please read the safety instructions in this manual ﬁrst. Throughout the manual it is assumed that the reader is familiar with AC and DC installations and knows the rules and regulations for electrical equipment and for connecting it to the utility AC grid. It is especially important to be familiar with the general safety rules for working with electrical equipment.

Applied designations
Throughout the manual important information is shown at different levels depending on the character of the information, as shown here:

Important safety information
Read this before installing, operating or maintaining the inverter.

Before installation: Check for damage to inverter and packaging. If you are in doubt, please contact your supplier before installing the inverter. Check the voltages of the solar modules and make sure they are within the limits of the inverter speciﬁcations before connecting them to the inverter.
Installation: Only trained and authorized personnel familiar with local electrical codes may install the inverter. For optimum safety, please follow the steps described in this manual. Keep in mind that the inverter has two voltage carrying sides, the PV input and the AC grid.
Disconnecting the inverter: Always disconnect the AC line ﬁrst! Afterwards disconnect the PV lines. Note that the inverter can still be charged with very high voltages at hazardous levels even when it is disconnected from grid and solar modules. Wait at least 5 min. before proceeding, after having disconnected from grid and PV panels.Don’t open the MC4 connectors under load condition or inverter working condition.
Operating the inverter: Before connecting the AC grid to the inverter, make sure that the installation cover is mounted again. The inverter must not be open during operation.
Maintenance and modiﬁcation: Only authorized personnel are allowed to repair or modify the inverter. To ensure optimum safety for user and environment, only the original spare parts available from your supplier should be used.
Functional safety parameters: Unauthorized changes of functional safety parameters may cause injury or accidents to people or inverter. Additionally it will lead to the cancelling of all inverter operating approval certiﬁcates.

System sizing

When dimensioning a photovoltaic system, it must be ensured that the open circuit voltage of the PV string never exceeds the maximum permissible input voltage of 600V DC. The PV string open circuit voltage during parallel string operation is 550V. Higher voltages may result in permanent damage to the inverter.
The selection of PV string output should be based on the optimum utilization of the invested capital compared to the expected annual energy yield from the system. This optimization depends on local weather conditions and should be considered in each individual case.
The inverter incorporates an input power limiting device, which automatically keeps the power at levels that are safe for the inverter. The limitation depends mainly on internal and ambient temperatures. The limitation is calculated continuously and always allows the maximum possible amount of energy to be produced.
Please use the tool supplied by Renac Power when dimensioning a photovoltaic system.

Technical description of inverters

Mechanical design
Figure 2-1 shows the outline dimensions of NAC4K-DS / NAC5K-DS / NAC6K-DS / R1 -8K-DS / R1-10K-DS / R1-10K5-DS.

Figure 2-2 shows the electrical terminals of NAC4K-DS / NAC5K-DS / NAC6K-DS / R1-8K-DS / R1-10K-DS / R1-10K5-DS.

No	Description
1	DC (PV terminal)
2	I/O Port
3	AC terminal
4	LED (Run/Fault)
5	DC Switch
6	Communication port
7	LCD
8	Key

Electrical system design
For safety reasons, the use of a DC switch is recommended. Between the PV modules and the power modules may be mandatory in some countrie.
Please refer to chapter 3 for the detail connecting and install methods.

Technical data

DC Input Data

Max. Recommended PV Power| 5200W| 6500W| 7800W
Max.DC Input Voltage| 600V
MPPT voltage Range| 100-550V
Rated input voltage| 360V
Start-up Voltage| 120V
No. of MPP Trackers| 2
No. of Input Strings per Tracker| 1 / 1| 2 / 1
Max. DC Input Current| 16A / 16A| 16A / 16A| 16A / 16A
DC Switch| Optional
AC Output Data|
Rated AC Power| 4000W| 5000 W| 6000W
Max.output power| 4400VA| 5500VA| 6600VA
Max. AC Current| 19.2A| 24A| 28.7A
Rated AC Voltage /Range| 220V/230V; 160-290V
Grid frequency / range| 50Hz/60Hz; ±5Hz
Adjustable Power Factor [cos φ]| 0.8leading ~ 0.8lagging
Output THDi (@Rated Output)| ≤ 2%
Efficiency

IEC60068, IEC61683, ABNT NBR 16150

Safety Regulation| IEC 62109-1, IEC 62109-2
EMC| EN 61000-3-2, EN 61000-3-3, EN 61000-3-11, EN 61000-3-12, EN 61000-6-2,

EN 61000-6-3, IEC 61000-4-16, IEC 61000-4-18, 4-29

DC Input Data

Max. Recommended PV Power| 12000W| 15000W| 16000W
Max.DC Input Voltage| 600V
MPPT voltage Range| 100-550V
Rated input voltage| 360V
Start-up Voltage| 120V
No. of MPP Trackers| 2
No. of Input Strings per Tracker| 2 / 1| 2 / 2
Max. DC Input Current| 26A / 20A| 26A / 26A| 26A / 26A
DC Switch| Optional
AC Output Data
Rated AC Power| 8000 W| 10000 W| 10440 W

Max.output power

|

8800VA

|

10000VA

| 9570VA@220V

10005VA@230V

10440VA@240V

Max. AC Current| 36.4A| 43.5A| 43.5A
Rated AC Voltage / Range| 220V/230V/240V; 160-290V
Grid frequency / range| 50Hz/60Hz; ±5Hz
Adjustable Power Factor [cos φ]| 0.8leading ~ 0.8lagging
Output THDi (@Rated Output)| ≤ 2%
Efficiency
Max.Efficiency| 97.8%| 98.1%| 98.1%
Euro Efficiency| 97.2%| 97.5%| 97.5%
MPPT Efficiency| 99.9%| 99.9%| 99.9%
Protection
DC Insulation Monitoring| Integrated
Input Reverse Polarity Protection| Integrated
Anti-island Protection| Integrated
Residual Current Monitoring| Integrated
Over-heat Protection| Integrated
AC Overcurrent Protection| Integrated
AC Short-circuit Protection| Integrated
AC Overvoltage Protection| Integrated
DC Surge Protection| Integrated (Type III)
---|---
AC Surge Protection| Integrated (Type III)
General Data|
Size (WidthHeightDepth)| 395 x 330 x 185mm
Weight| 16KG
User Interface| LCD
Communication| RS485 (Standard), Wiﬁ or GPRS
Ambient Temperature Range| -25 ℃ ~ 60 ℃
Relative Humidity| 0-100%
Operating Altitude| ≤ 4000m
Standby Self Consumption| < 0.2W
Topology| Transformerless
Cooling| Natural| Fan| Fan
Protection Grades| IP65
Noise| < 30dB| < 40dB
Warranty| 5 / 7 / 10 years
Certiﬁcations & Standards|
Grid Regulation| EC61727, IEC62116, IEC60068, IEC61683, ABNT NBR 16150
Safety Regulation| IEC 62109-1, IEC 62109-2
EMC| EN 61000-3-2, EN 61000-3-3, EN 61000-3-11, EN 61000-3-12, EN 61000-6-2,

EN 61000-6-3, IEC61000-4-16, IEC61000-4-18, IEC61000-4-29

Grid Codes

No.	National/Regional Grid Code	Description
1	VDE4105-DE	Germany power Grid, meet Grid standards “VDE-AR-N-4105”.
2	CEI0-21	Italy power Grid.
3	AS4777	Australia power Grid.
4	RD1699	Spain power Grid.
5	EN50549-TR	Turkey power Grid.
6	EN50549-DK	Denmark power Grid.
7	Greece	Greece power Grid.
8	EN50549-NL	Netherland power Grid, meet Grid standards “EN50438”.
9	C10/11	Belgium power Grid.
---	---	---
10	G59	UK power Grid.
11	China	China power Grid, meet Grid standards “CN-NBT”.
12	VDE0126-FR	France power Grid, meet Grid standards “VDE 0126”.
13	EN50549-PL	Poland power Grid.
14	BDEW-DE	Germany power Grid, meet Grid standards “BDEW-MV”.
15	VDE0126-DE	Germany power Grid, meet Grid standards “VDE 0126”.
16	CEI0-16	Italy power Grid, meet Grid standards “CEI 0-16”.
17	G83	UK power Grid.
18	Greece Island	Greece Island power Grid.
19	EN50549-CZ	Czech Republic power Grid, meet Grid standards

23

|

China-W

| China power Grid, Grid voltage range：160-290V

Grid frequency range：47-53HZ.

Installation and startup

Warning！ Before installation and maintenance, AC and DC side doesn’t carry electricity, but if DC side is just disconnected, capacitance still contains electricity, so please wait for at least 5 minutes to ensure the capacitors completely release the energy and inverter is not electriﬁed.
Note！ Inverters must be installed by qualiﬁed person.

Package information

There are 2 PV+ connectors for 4/5/6K-DS , 3 PV+ connectors for 7/8K-DS and 4 PV+ connectors for 9/10/10.5K-DS
There are 2 PV- connectors for 4/5/6K-DS , 3 PV- connectors for 7/8K-DS and 4 PV- connectors for 9/10/10.5K-DS

Installation environment

In order to achieve optimal performance, the ambient temperature should be kept lower than 45 °C.
For the convenience of checking the LCD display and possible maintenance activities, please install the inverter at eye level.
Inverters should NOT be installed near inﬂammable or explosive items. Any strong electro-magnetic equipment should be kept away from installation site.
Product label and warning symbol shall be clear to read after installation.
Please do not install inverter under direct sunlight, rain and snow.

Installation position

The installation method and mounting location must be suitable for the inverter’s weight and dimensions.
Mount on a solid surface.
Select a well-ventilated place sheltered from direct sun radiation.

In consideration of heat dissipation and convenient dismantlement, the minimum clearances around the inverter should be no less than the following value:

Mounting procedure

Step1 : Drill 4 Fix Ø11 holes in the wall according to the dimensions.
Step2: Fix the wall mounting bracket on the wall with 4 expansion bolts in accessory bag. Step3: Place the inverter on the wall-mounted bracket and install the ﬁx screw.

Electrical connection

Connection to the grid (AC output)

Add breaker or fuse to AC side, the speciﬁcation should be more than 1.25 times of rated AC output current.
The PE line of inverter should be connected to the earth, make sure the impedance of neutral wire and earth wire less than 10 ohm.
Disconnect the breaker or fuse between the inverter and the utility.
All inverters incorporate a certiﬁed internal Residual Current Device (RCD) in order to protect against possible electrocution and ﬁre hazard in case of a malfunction in the PV array, cables or inverter. There are 2 trip thresholds for the RCD as required for certiﬁcation (IEC 62109-2:2011). The default value for electrocution protection is 30mA, and for slow rising current is 300mA.

Connect the inverter to the grid as follows:

Strip off L/N/PE cables as ﬁgure 3-6
No.| Description| Remark
---|---|---
A| Protective layer| Diameter ranges ：9-16mm
B| Length of stripped off| 12mm
C| Insulate layer| 50mm
D| Cross section of ac cables| 6-10mm²
Tighten the nut clockwise & Tighten L/N/PE cable screws to th e terminals according to markings.
TIP : Fix (Torque: 2~2.5 N.m) the connector of AC cable to the corres ponding terminals
Plug Grid side connector into AC connector of inverter end, rotate and tighten clockwise.

Connection to PV string (DC input)

Before connecting PV string, make sure DC switch is turned off.
Make sure PV string polarity confirms with DC connector, otherwise, it will cause damage to inverter.
Make sure the maximum open circuit voltage (Voc) of each PV str ing does not exceed the inverter input voltage Vmax under any condition.
Do not connect positive or negative pole of PV string to earth wire. Otherwise, it will cause damage to inverter.

Communication

Overview of communication ports:

WIFI/GPRS Communication (optional)
Connect the WIFI/GPRS module produced by Renac to the COM port of inverter. After successful connection, information such as power generation and running state of the inverter can be viewed via the App on the phone. The details please refer to the module user manual.
The block diagram of the WIFI/GPRS communication system is as follows：

The inverter is equipped with the feed-in power limit function, and the communication port on inverter is “CT” (figure 3-9), below is the method of connecting the CT in system.

DRM connection
The inverter supports the demand response modes as speciﬁed in the standard AS/NZS4777. The inverter has integrated a terminal for connecting to a DRED. The details please refer to ﬁgure 3-9, and for CEI standard, DRM S0 is the DI port .
Relay connection
The relay can be set to fault alarm output, and user can conﬁgure it to be a normal open contact (COM＆NO) or a normal close contact (COM＆NC).The relay is initially at the NC terminal, and it will trip to another contact when a fault occurs. Use LED indicators or other equipment to indicate whether the inverter is in the faulty state. The following ﬁgures show the typical applications of normal open contact and normal close contact:

Starting the inverter

Before turn on the inverter, please conﬁrm:

Three AC wires (PE/L/N) cable correctly connected to the inverter AC side through AC circuit breaker;
The DC cable connected correctly to the inverter DC side through DC circuit breaker, please be attention to the cable connected to the two string correctly and it’s polarity;
The unused terminals are covered.

Starting the inverter

Close the DC and AC circuit breaker;
If the solar panels provide enough energy, the power module will work and the LCD panel will be lit;
In case you are starting the inverter for the ﬁrst time, the inverter needs to be commissioned. Commissioning is described on page 19,chapter 4.3.
Then the inverter will turn into self-check mode and the LCD panel will display the remaining time of connect simultaneously;
After the inverter turn into normal mode, it feed electrical energy into grid, and LCD panel will display the generated electrical energy.

As long as the inverter works, it will automatically track the maximum power point to absorb the maximum energy from solar. When night comes, the irradiance is not strong enough to provide energy, the inverter will power off automatically. When the next day comes, the input voltage reaches the start value, it will start again automatically.

User interface

Led and key

No.	Object	Description

1

| Run

(Green LED)

| On = Normal operation
Flashing = Waiting, checking or starting up

1

| Fault

(Red LED)

| On = Failure
Flashing = Temporary failure

2

|

Pushbutton

| Pressing < 1 s: Next
Pressing > 2 s: Enter

LCD display

Menu structure

→ Press the button less than 1 second
→long Press the button
→Return

Factory setting

Press pushbutton long in order to enter the “Factory setting” m enu.
Press pushbutton long to enter the “language setting” menu.
Press pushbutton less than 1 sec. to the langue menu you want a nd Press pushbutton long to select.
Press pushbutton less than 1 sec. to the country menu you want and Press pushbutton long to select.

Setting language

Press pushbutton less than 1 sec. several times until you reach the “Setting” menu.
Press pushbutton long in order to enter the “setting” menu.
Press pushbutton less than 1 sec. several times until you reach the “language setting” menu.
Press pushbutton less than 1 sec. to the langue menu you want and Press pushbutton long to select.

Setting modbus address

Press pushbutton less than 1 sec. several times until you reach the “Setting” menu.
Press pushbutton long in order to enter the “setting” menu.
Press pushbutton less than 1 sec. several times until you reach the “module add” menu.
Press pushbutton less than 1 sec. to the modbus address number you want and Press pushbutton long to set.

Setting export power (CT)

Press pushbutton less than 1 sec. several times until you reach the “Setting” menu.
Press pushbutton long in order to enter the “setting” menu.
Press pushbutton less than 1 sec. several times until you reach the “Export power” menu.
Press pushbutton long to enter onto “Export power”.
Set “Export power” as “1”, press pushbutton long to save the va lue.

Self-Test in accordance with CEI 0-21 (Applies to Italy only)

The self-test is only required for inverters, which are commissioned in Italy. The Italian standard requires that all inverters feeding into the utility grid are equipped with a self-test fun ction in accordance with CEI 0-21. During the self-test, the inverter will consecutively check the protection reaction times and values for overvoltage, under voltage, over frequency and under frequency.
Self-test function is available at any time. It also allows end user get test reports shown on LCD display. There are two ways to execute the self-test:

Auto-Test from screen:

Press pushbutton less than 1 sec. several times until you reach the “Setting” menu.
Press pushbutton long in order to enter the “setting” menu.
Press pushbutton less than 1 sec. several times until you reach the “AutoTest-Italy” menu (You need to set the inverte country to CEI 0-21 before testing).
Press pushbutton long to execute the auto-test.
The inverter will automatically run the test until the screen shows “Test end”, if the test passes, it will show “test ok”, if the test is failed, it will show “test failed”.

Auto-Test from Solar Admin:

Download and install “Solar Admin” on laptop.
Connect inverter to laptop via RS485 port.
When the inverter and “solar admin” are successfully connected. Click “Sys.setting” – “Other” – “AUTOTEST” enter into “Auto-Test” interface.
Click “Execute” to start the test.
The inverter will automatically run the test until the screen shows “Test end”.
Click “Read” to read the test value, and click “Export” to export the test report.
After click “Read” button, interface will show the test results, if the test passes, it will show “PASS”, if the test is failed, it will show “FAIL”.

Warranty

The standard warranty period for the inverter is 60 months from the date of installation and no more than 66 months (5.5 years) from the date of shipment from factory.

Warranty claim procedure

Please report defective device with a brief error description and SN code to our service mail or service hotline for registration. Alternatively, please contact your speciﬁc dealer or installer if your unit is defective or faulty. To claim the warranty under the warranty terms of factory, you need to supply us with the following information and documentation regarding the faulty unit:

Product Model No (e.g. R1-8K-DS) and the serial Number (e.g. 87 00831201211006).
Copy of the invoice and warranty certificate for the inverter.
Error message on LCD screen and additional information regarding the fault/error.
Detailed information about the entire system (modules, circuits, etc.).
Documentation of previous claim/exchanges ( if applicable).

In the case of an exchange, the remainder of the warranty entit lement will be transferred to the replacement device. In this event, you will not receive a new certificate, as this repl acement will be noted by factory.

Service after warranty expiration

For products which are out of warranty, factory charges an on-site service fee, parts, labor cost and logistic fee to end-user which can be any/all of:

On-site attendance fee : Cost of travel and time for the technician in attending on-site;
Parts : Cost of replacement parts (including any shipping/admin fee that may apply);
Labor : Labor time fee charged for the technician, who is repairing, maintaining, and installing (hardware or software) and debugging the faulty product;
Logistic fee: Cost of delivery, tariff and other derived expense when defective products are sent from user to factory or / and repaired products are sent from factory to user;

Troubleshooting and Maintenance

Troubleshooting

Once a fault occurs in the inverter, the fault information can be displayed on screen or the App interface. Fault codes and check methods are as follows:

Fault	LCD display	Possible actions

Clearable Fault

| Isolation Fault1

Isolation Fault2

| 1. Check whether the inverter is earthed and test impedance between PV (+) & (-) and the impedance must exceed 3MΩ;

2. Check whether the AC-side has contacts with earth.

Grid Faults: 10min OVR Fault OVR Fault UVR Fault OFR Fault UFR

|

1. Wait for 5 minutes, if the grid returns to normal, PV inverter automatically

restarts.

2. Make sure grid voltage and frequency meet the local speciﬁcations.

No utility

|

1. Grid is not connected.

2. Check grid connection cables.

3. Check grid usability.

4. If grid is ok and the problem exists still, maybe the fuse in the inverter is open, please call service.

Low Temp Over Temp

|

1. The internal temperature of inverter is higher or lower than speciﬁed

normal value.

2. Find a way to reduce or increase the ambient temperature.

3. if the problem remains, please call local service

PV over Voltage: PV1OVFault PV2OVFault

|

1. Check the open PV DC voltage, and see if it is greater than or too close to 550VDC

2. If PV DC voltage is less than 550VDC, and the problem still occurs, please

call local service.

Permanent Fault

|

Consistent Faults: Consist VGrid Consist Freq Consist GFCI Consist DCI

|

1. Disconnect all PV (+) or PV (-) from solar panels

2. Wait for a few seconds.

3. After the LCD switches off, reconnect and check again.

4. If the problem remains, please call local service.

---|---|---
RelayFail
EEPROM R/W Fail
Sci Comm lose
Spi Comm lose
BusHFault
GFCIDeviceFault
IGridDevice
PLLFault
AutoTestFail
PV Conﬁg fault
Fan error
DCI out range
OCPV1
OCPV2
OCIGrid

Maintenance

Risk of inverter damage or personal injury due to incorrect service!

Always keep in mind that the inverter is powered by dual sour ces: PV strings and utility grid. Before any service work, observe the following procedure.
Disconnect the AC circuit breaker and then set the DC load-break switch of the inverter to OFF.
Wait at least 5 minutes for inner capacitors to discharge com pletely.
Verify that there is no voltage or current before pulling any connector.

NOTICE
Restart the inverter only after removing the fault that impairs safety performance. As the inverter contains no component parts that can be maintained, ne ver arbitrarily replace any internal components. For any maintenance need, please contact R enac Power. Otherwise, Renac Power shall not be held liable for any damage caused.

Routine Maintenance

Item	LCD display	Period

System clean

| Check the temperature and dust of the inverter. Clean the inverter enclosure if necessary. Check if the air inlet and outlet are normal. Clean the air inlet and outlet,

if necessary.

|

Six months to a year (- depend on the dust contents in air.)

Fans

|

Check whether there is any abnormal noise when the fan is turning. Clean or replace the fans if necessary (see

the following section).

|

Once a year

Cable entry

|

Check whether the cable entry is insufficiently sealed or the gap is excessively large, and reseal the entry when necessary.

|

Once a year

Electrical Connection

|

Check whether all cable are ﬁrmly in place. Check whether a cable is damaged, especially the part contacting

the metal enclosure.

|

Six months to a year

Maintenance Instruction
Cleaning Air Inlet and Outlet
A huge amount of heat is generated in the process of running th e inverter. The inverter adopts a controlled forced-air cooling method. In order to maintain good ventilation, please c heck to make sure the air inlet and outlet are not blocked. Clean the air inlet and outlet with soft brush or vacuum cleane r if necessary.
Fan Maintenance

Stop the inverter and disconnect it from all power supplies b efore maintenance.
Lethal voltage still exists in the inverter. Please wait for at least 5 minutes and then perform maintenance work.
Only qualified electricians can maintain the fans.

Fans inside the inverter are used to cool the inverter during operation. If the fans do not operate normally, the inverter may not be cooled down and inverter efficiency may decrease. Therefore, it is necessary to clean the dirty fans and replace the broken fans in time.
The operation procedure is as follows:

Step 1 Stop the inverter (turns off DC and AC both for inverter, wait for at least 5 minutes).
Step 2 Loosen the 4 screws of the 2 fan modules.
Step 3 Loosen the 4 screws for each fan module.
Step 4 Disconnect the fan cables and then pull out the fan modu les, clean the fans with soft brush or vacuum cleaner, and replace them when necessary.
Step 5 Reinstall the fan back to the inverter in reverse order and restart the inverter.

SMART ENERGY FOR BETTER LIFE

FAQ’s

What should I do if I encounter high voltage warnings?
If you encounter high voltage warnings, immediately turn off and disconnect the inverter to ensure safety. Refer to the user manual for specific safety instructions.

How should I dispose of the product?
The product should not be disposed of as normal household waste. Please follow proper disposal guidelines to protect the environment.