SONY XAV-3600 In Car Receiver Instruction Manual

: August 6, 2024
: Sony

Table of Contents

XAV-3600 In Car Receiver
Product Information
Specifications:
- Product Usage Instructions
Installation:
Safety Precautions:
Function Update:
- FAQ
Question 1: What should I do if the unit becomes hot during
Question 2: How can I prevent battery drain when using this
Question 3: Can I install this unit in any vehicle?

XAV-3600 In Car Receiver

“`html

Product Information

Specifications:

Model: XAV-3600
Operating Voltage: Refer to nameplate on the chassis
Compliance: FCC Part 15 and ISED licence-exempt RSS(s)
Antenna: Not to be co-located or operated with any other
transmitter
Radiation Exposure: Complies with FCC/ISED limits for
uncontrolled environment

Product Usage Instructions

Installation:

For safety, install the unit in the car’s dashboard as the rear
side may become hot during use. Refer to the
Connection/Installation section in the manual for detailed
instructions.

Safety Precautions:

Avoid exposing the unit to rain or moisture to prevent fire or
shock hazard.
Do not open the cabinet to avoid electrical shock. Seek
servicing from qualified personnel if needed.
Do not make any changes or modifications not approved in the
manual to maintain operational authority.

Function Update:

For the latest functions, visit the Help Guide on the provided
website. The QR code and URL can be found on the front cover of the
manual.

FAQ

Question 1: What should I do if the unit becomes hot during

use?

Answer: Ensure proper ventilation and do not block any vents. If
the unit continues to overheat, turn it off and seek assistance
from a professional.

Question 2: How can I prevent battery drain when using this

unit?

Answer: Do not install the unit in a car without an ACC position
in the ignition. The display may not turn off after ignition,
leading to battery drain.

Question 3: Can I install this unit in any vehicle?

Answer: It is recommended to install this unit only in vehicles
with proper ventilation and compatible power configurations. Refer
to the manual for specific installation guidelines.

“`

F:Works50556921115055692111XAV3600UC0COV-XAV3600C10COV.fm 010COV.book Page 1 Tuesday, September 12, 2023 3:34 PM

masterpage: Cover 5-055-692-11(1)

AV RECEIVER

Operating Instructions EN

Mode d’emploi

FR

Manual de instrucciones ES

Owner’s Record
The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. XAV-3600
Serial No.
To cancel the demonstration (Demo) display, see page 6. Pour annuler l’affichage de démonstration (Démo), reportezvous à la page 7. Para cancelar la pantalla de demostración (Demostración), consulte la página 7.

XAV-3600(UC) https://rd1.sony.net/help/ev/xav-ax32/h_zz/

XAV-3600

XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC20INT.fm 010COV.book Page 2 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Warning
For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use. For details, see “Connection/Installation” (page 9).
FOR CUSTOMERS IN CANADA (INCLUDING IN THE PROVINCE OF QUEBEC) ALL INSTRUCTIONS AND STATEMENTS WHICH ARE NECESSARY FOR CANADIAN CUSTOMERS ARE PROVIDED IN ENGLISH AND FRENCH. OTHER INSTRUCTIONS AND STATEMENTS NOT PROVIDED IN ENGLISH AND FRENCH ARE NOT FOR CANADIAN CUSTOMERS (INCLUDING IN THE PROVINCE OF QUEBEC).
The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
2EN

This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy.
If you have any questions about this product: Visit: https://www.sony.com/electronics/support Contact: Sony Customer Information Service Center at 1-800-222-7669 Supplier’s Declaration of Conformity Trade Name: SONY Model: XAV-3600 Responsible Party: Sony Electronics Inc. Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning if your car’s ignition has no ACC position Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.
Disclaimer regarding services offered by third parties Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.
About function update of the unit For the latest functions, refer to “Help Guide” on the website. The QR code and URL can be found on the front cover.

XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC20INT.fm 010COV.book Page 3 Tuesday, September 12, 2023 3:34 PM

masterpage: Right_ A

Important notice
Caution IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.
Dear customer, this product includes a radio transmitter. Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.
Emergency calls This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).
On BLUETOOTH communication · Microwaves emitting from a BLUETOOTH device
may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident. where inflammable gas is present, in a hospital,
train, airplane, or petrol station near automatic doors or a fire alarm · This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology. · We do not take any responsibility for the leakage of information during BLUETOOTH communication.
If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

3EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 4 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Guide to Parts and Controls
Main Unit

Screen Displays
Playback screen:

The VOL (volume) + button has a tactile dot.
Display/touch screen
HOME Displays the HOME screen (page 4).
ATT (attenuate) Press and hold for 1 second to attenuate the sound. To cancel, press and hold again, or press VOL +.
VOL (volume) +/
/ (previous/next) Functions differently depending on the selected source: [Radio]: select a preset station. [USB]/[Bluetooth]: move to the previous/next file. Press and hold to: [Radio]: tune into a station automatically (SEEK+/SEEK). [USB]/[Bluetooth]: fast-reverse/fast-forward.
OPTION Displays the OPTION screen (page 4).

HOME screen: OPTION screen:

4EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 5 Tuesday, September 12, 2023 3:34 PM

masterpage: Right

Status indication
Lights up when the sound is attenuated.
Lights up when the Bluetooth® signal is on. Flashes when the connection is in progress.
Lights up when the audio device is playable by enabling the A2DP (Advanced Audio Distribution Profile).
Lights up when handsfree calling is available by enabling the HFP (Handsfree Profile).
Indicates the signal strength status of the connected mobile phone.
Indicates the remaining battery status of the connected mobile phone.

(source option) Opens the source option menu. The available items differ depending on the source.
Application specific area Displays playback controls/indications or show the unit’s status. Displayed items differ depending on the source.
Clock Displays the time which are set on the Date/Time setting.
(return to the playback screen) Switches from the HOME screen to the playback screen.
Sources and Settings select keys Changes the source or make various settings. Flick to select the setting icon and other icons. Touch the source icon you want to select.

Radio

Bluetooth

Phone

USB
Rear Camera

WebLink* Settings

HDMI

WebLink icon appears when the smartphone is connected.
Sound select keys Changes the sound.
(standby) Turns the unit in standby mode (USB charging is still available). To resume, press any buttons.
(monitor off) Turns off the monitor. When the monitor is turned off, touch any part of the display to turn it back on.
(EXTRA BASS) Changes the EXTRA BASS setting.

(EQ10/Subwoofer) Changes the EQ10/Subwoofer setting.

5EN

XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 6 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Basic Operations
Pairing with a BLUETOOTH Device
When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

1 Press HOME, then touch [Settings] [Bluetooth] [Bluetooth Connection] [ON] [Pairing].
flashes while the unit is in pairing standby mode.
2 Perform pairing on the BLUETOOTH device
so it detects this unit.
3 Select your model name shown on the
display of the BLUETOOTH device*. When pairing is made, stays lit.

If passkey input is required on the BLUETOOTH device, input [0000].

Canceling the Demonstration Mode

1 Press HOME, then touch [Settings].

2 Touch [General], then touch [Demo] to set to
[OFF].

3 To exit the setup menu, touch
twice.

(back)

Updating the Firmware
To update the firmware, visit the support site, then follow the online instructions. URL: https://www.sony.com/am/support
Note During the update, do not remove the USB device.

6EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 7 Tuesday, September 12, 2023 3:34 PM

masterpage: Right

Additional Information
Precautions
Note on safety Comply with your local traffic rules, laws, and regulations.
About iPhone
· Compatible iPhone models: iPhone 14 Pro Max, iPhone 14 Pro, iPhone 14 Plus, iPhone 14, iPhone SE (3rd generation), iPhone 13 Pro Max, iPhone 13 Pro, iPhone 13, iPhone 13 mini, iPhone 12 Pro Max, iPhone 12 Pro, iPhone 12, iPhone 12 mini, iPhone SE (2nd generation), iPhone 11 Pro Max, iPhone 11 Pro, iPhone 11, iPhone XS Max, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s
· Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with an Apple product may affect wireless performance.
Notice on license
This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of copyright for the software. For details on software licenses, select [Settings] [General] [Open Source Licenses].
If you have any questions or problems concerning your unit that are not covered in this Operating Instructions, consult your nearest Sony dealer.

Specifications
AUDIO POWER SPECIFICATIONS CTA2006 Standard Continuous Power Output: 20 W RMS × 4 Channels at 4 and 1% THD+N Signal to Noise: 80 dBA reference 1 Watt RMS
Monitor section
Display type: Wide LCD color monitor Dimensions: 17.1 cm/ 6.75 in System: TFT active matrix Number of pixels:
1 152 000 pixels (800 × 3 (RGB) × 480) Color system:
PAL/NTSC automatic select for CAMERA IN terminal
Radio section
FM Tuning range: 87.5 MHz 107.9 MHz Usable sensitivity: 7 dBf Signal-to- noise ratio: 70 dB (mono) Separation at 1 kHz: 45 dB
AM Tuning range: 530 kHz 1 710 kHz Sensitivity: 32 V
USB player section
Interface: USB (Hi-speed) Maximum current: 1.5 A
HDMI section*
Input format: 480p, 576p, 720p

HDMI output is not available.
Wireless communication
Communication System: BLUETOOTH Standard version 3.0
Output: BLUETOOTH Standard Power Class 2 (Max. Conducted +1 dBm)
Maximum communication range*1: Line of sight approx. 10 m (33 ft)
Frequency band: 2.4 GHz band (2.400 0 GHz 2.483 5 GHz)
Modulation method: FHSS

7EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 8 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Compatible BLUETOOTH Profiles2: A2DP (Advanced Audio Distribution Profile) 1.3 AVRCP (Audio Video Remote Control Profile) 1.3 HFP (Handsfree Profile) 1.6 PBAP (Phone Book Access Profile) 1.1
Corresponding codec: SBC, AAC
1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna (aerial) performance, operating system, software application, etc.
*2 BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.
Power amplifier section
Outputs: Speaker outputs Speaker impedance: 4 8 Maximum power output: 55 W × 4 (at 4 )
General
Power requirements: 12 V DC car battery (negative ground (earth))
Rated current consumption: 10 A Dimensions:
Approx. 178 mm × 100 mm × 139 mm (7 1/8 in × 4 in × 5 1/2 in) (w/h/d)
Mounting dimensions: Approx. 182 mm × 111 mm × 120 mm (7 1/4 in × 4 3/8 in × 4 3/4 in) (w/h/d)
Mass: Approx. 1.0 kg (2 lb 4 oz) Package contents:
Main unit (1) Parts for installation and connections (1 set)
Ask the dealer for detailed information.
Design and specifications are subject to change without notice.

Copyrights
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Group Corporation and its subsidiaries is under license. Other trademarks and trade names are those of their respective owners.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.
Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
WebLink is a registered trademark of Abalta Technologies, Inc. in the U.S. and a trademark in the other countries.
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
All other trademarks are trademarks of their respective owners.

8EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 9 Tuesday, September 12, 2023 3:34 PM

masterpage: Right

Connection/Installation
Cautions
· Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.
· Run all ground (earth) leads to a common ground (earth) point.
· Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing).
· Before making connections, turn the car ignition off to avoid short circuits.
· Connect the yellow and red power supply leads only after all other leads have been connected.
· Be sure to insulate any loose unconnected leads with electrical tape for safety.
· Choose the installation location carefully so that the unit will not interfere with normal driving operations.
· Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
· Use only the supplied mounting hardware for a safe and secure installation.
Note on the power supply lead (yellow) When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating.
Note on installing in cars with a start-stop system The unit may restart when starting the engine from startstop. In this case, turn off the start-stop system of your car.
Note on installing in cars with electric parking brake system For cars with electric parking brakes, some related functions (such as video blocking function) may not work properly.
Mounting angle adjustment Adjust the mounting angle to less than 30°.

Parts List for Installation

Power supply leads (1)

Mounting screw (5 × max. 9 mm (7/32 × max. 3/8 in)) (4)

Microphone (1)

Flat-mount base (1)

Double-sided tape (1)

Cable for steering wheel remote input (RC-SR1) (1)

Cable tie (1)

This parts list does not include all the package contents.

9EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 10 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Connection

· To prevent short circuits, insulate leads with a cover or tape. · Note that the unit may be damaged if it is connected incorrectly or by short circuits at the leads.

Subwoofer1 3

*3

Power amplifier*1

*3

Rear view

camera*1

67 from a steering wheel remote control4
Smartphone, USB device (for audio/video playback)1

10EN

White White/black striped Gray Gray/black striped Green Green/black striped Purple Purple/black striped Black Yellow Red Blue/white striped Orange/white striped Light green Purple/white striped

Front speaker12
Rear speaker12
For details, see “Making connections” (page 11).
from an HDMI device18 from a car antenna (aerial)15

XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 11 Tuesday, September 12, 2023 3:34 PM

masterpage: Right

1 Not supplied 2 Speaker impedance: 4 to 8 × 4 3 RCA pin cord (not supplied) 4 Depending on the type of car, use an adaptor for the
steering wheel remote control (not supplied). For details on using the steering wheel remote control, see “Using the steering wheel remote control” (page 12). 5 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit. 6 Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet. 7 For details on installing the microphone, see “Installing the microphone” (page 12). 8 For details on using an HDMI device, see “Using an HDMI device” (page 13).
Making connections
To a common ground (earth) point First connect the black ground (earth) lead then connect the yellow and red power supply leads.
To the +12 V power terminal which is energized at all times Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
To the +12 V power terminal which is energized when the ignition switch is set to the accessory position Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually- operated telescopic antenna (aerial). To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.
Note It will take about 10 seconds to shut down the output of REM OUT after the unit is turned off.
To a car’s illumination signal Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

To the parking brake switch lead The mounting position of the parking brake switch lead depends on your car. Be sure to connect the parking brake lead (light green) of the power supply leads to the parking brake switch lead.
Parking brake switch lead

Hand brake type

Foot brake type

To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rear view camera)
Rear View Camera Connection
Installation of a rear view camera (not supplied) is required before use.
Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.
Speaker connection
· Before connecting the speakers, turn the unit off. · Use speakers with an impedance of 4 to 8 and
with adequate power handling capacities to avoid damage.

11EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 12 Tuesday, September 12, 2023 3:34 PM

masterpage: Left

Installing the microphone
To capture your voice during handsfree calling, you need to install the microphone .

Clip (not supplied)

Cautions · It is extremely dangerous if the cord becomes
wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations. · If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation.
Notes · When mounting on the dashboard, remove the visor clip
carefully from the microphone , then attach the flatmount base to the microphone . · Before attaching the double-sided tape , clean the surface of the dashboard with a dry cloth.

Using the steering wheel remote control
When using the steering wheel remote control Installation of the connection cable RC-SR1 is required before use.
1 To enable the steering wheel remote
control, select [General] [Steering Control] [Custom] to make the registration. When the registration is complete, the steering wheel remote control becomes available.
Notes on installing the connection cable RCSR1
REMOTE IN
GND
Input 1
Input 2
Black Green Brown
· Before installing, turn on the car ignition then check that the steering wheel control buttons are working correctly.
· Refer to the support site for details then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit. URL: https://www.sony.com/am/support
· Consulting the dealer or an experienced technician for help is recommended.
When using an adaptor for the steering wheel remote control Depending on the type of car, use an adaptor for the steering wheel remote control (not supplied).
1 Set [Steering Control] in [General] to
[Preset]. The adaptor for the steering wheel remote control is enabled.

12EN

XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC1GB-XAV3600UC40CD.fm 010COV.book Page 13 Tuesday, September 12, 2023 3:34 PM

masterpage: Right

Using an HDMI device
Installation of an HDMI cable (not supplied) is required before use.
1 Connect an HDMI cable to the HDMI
terminal at the back panel of the unit.
2 Pass the cable tie through the cable
holder, then tie the cable tie around the HDMI cable. The HDMI cable is secured to the unit.

Installation
Mounting the unit in a Japanese car
You may not be able to install this unit in some Japanese cars. In such a case, consult your Sony dealer.

To the dashboard/center console

HDMI cable (not supplied)
3 Connect the installed HDMI cable to an
HDMI device.
4 Press HOME, then touch [HDMI].
The HDMI device connected will be mirrored to this unit.

Bracket

Parts supplied with

your car

When mounting this unit to the preinstalled brackets of your car, use the mounting screws in the appropriate screw holes based on your car: T for TOYOTA and N for NISSAN.

Note To prevent a malfunction, install only with the mounting screws .

Fuse replacement

When replacing the fuse, be sure to

Fuse (10 A)

use one matching the amperage

rating stated on the original fuse.

If the fuse blows, check the power

connection and replace the fuse.

If the fuse blows again after

replacement, there may be an

internal malfunction. In such a case, consult your

nearest Sony dealer.

13EN
XAV-3600 5-055-692-11(1)

F:Works50556921115055692111XAV3600UC0COV-XAV3600C50BCO.fm 010COV.book Page 14 Tuesday, September 12, 2023 3:34 PM

masterpage: BCO

If you have any questions/problems regarding this product, try the following:
1 Read Troubleshooting in
Help Guide (online manual).
2 Please contact (U.S.A. only);
Call 1-800-222-7669 URL https://www.SONY.com

https://www.sony.net/
XAV-3600 5-055-692-11(1)