Westclox Source 43000 series Big Ben Moon Beam Alarm Clock User Manual

Westclox Source 43000 series Big Ben Moon Beam Alarm Clock User Manual

The following instructions define how to operate the Moonbeam electric alarm clock with a gently awakening blinking lamp feature.

DESCRIPTION

BATTERY BACK UP

This clock has provision for you to install two “AA” size 1.5 volt alkaline batteries (not provided) to maintain the clock operation in the event of a power failure. Should a power failure occur, and good batteries are installed, the clock will maintain time and the audible wakeup bell alarm will sound when the time of day coincides with the alarm wakeup time setting, provided the alarm selection switch is in the ON position. During a power failure, when the clock is operating from the backup batteries, the clock dial light will not illuminate to conserve battery life. If you do not install good backup batteries the clock will not function during a power failure and the clock must be reset when the power returns. Installing good backup batteries allows you to unplug the clock and move it from one place to another without having to reset the time of day.

NOTE: If, after a power failure, the displayed time is not correct, the backup batteries should be replaced.

TO INSTALL THE BACKUP BATTERIES

1. Remove the access cover to the battery compartment in the bottom of the unit.
2. Install two fresh “AA” size 1.5-volt alkaline type batteries, observing the polarity markings inside the battery compartment.
3. Replace the battery compartment cover.

IMPORTANT : Remove batteries if the unit is to be unplugged from the AC outlet for more than a day, or if the unit is to be stored for an extended period.

This will prevent batteries from being drained. Overextended storage periods, batteries can leak and damage the unit. Leaky batteries should be discarded immediately. Skin burns or other personal injury can result. Always dispose of batteries according to federal, state, and local regulations.

TO SET THE TIME OF DAY

1. When viewed from the front of the unit, the left-hand set knob (1) located in the recessed back of the unit (behind the clock) is used to rotate the hour and minute hands to set the time of day.
2. Rotate this knob clockwise or counter clockwise until the minute and hour hands indicate the desired time of day.

TO SET THE ALARM WAKEUP TIME

1. When viewed from the front of the unit, the right-hand set knob (2) located in the recessed back of the unit (behind the clock) is used to rotate the alarm indicator hand to set the alarm wakeup time.
2. Rotate this knob clockwise or counterclockwise until the alarm indicator hand indicates the desired
   wakeup time.

TO OPERATE THE ALARM

1. Move the alarm selection switch (3) located on the back of the unit above the time and alarm set knobs to its top ON position before going to bed.
2. At five minutes before the alarm wakeup time setting, the lamp will come on intermittently blinking on and off to gently start the wakeup process.
3. When the time of day coincides with the alarm wake-up time setting, the audible bell wake-up alarm will sound.
4. Moving the alarm selection switch (3) to its lower OFF position turns the audible bell wakeup alarm sound and the blinking lamp off.
5. With alarm selection switch (3) in its lower OFF position, neither the blinking lamp or audible wakeup alarm will function.
6. The audible wakeup alarm sound and blinking lamp will automatically turn off in 35 minutes.

TO OPERATE THE SNOOZE FUNCTION

1. When the lamp turns on or if both the lamp is blinking and the audible bell alarm is sounding, pressing and releasing the top snooze button (4) will interrupt the blinking lamp or both the blinking lamp and audible bell alarm sound for ten minutes.
2. In five minutes the lamp will continue to blink on and off and at the end of the ten-minute snooze period, the bell alarm will sound.
3. The snooze function may be repeated up to four times.

TO REPLACE THE LAMP

NOTICE : USE ONLY A LAMP RATED FOR 120 VOLTS AC, 10 WATTS AS A REPLACEMENT.

1. With the front of the clock lying facing down in one hand and side of the clock opposite the lamp next to you, with the other hand, grasp the lamp access cover with your fingers tips on the edge of the lamp access cover edge with the triangular indicator and pull toward you and upward to open the access cover and expose the lamp.

2. With the fingers, grasp the glass envelope of the lamp pushing the lamp toward its socket while rotating the lamp counterclockwise as far as it will go.
   CAUTION: Care should be taken when removing or replacing the lamp. Too much pressure exerted on the glass envelope of the lamp can cause it to shatter and you can be cut by the raw edges.

3. Lift up on the lamp to remove it.

4. Position the pins of the replacement lamp to align them with the cutouts in the metal base of the lamp socket inside the lamp socket housing.

5. Press the lamp down and rotate clockwise to seat the pins into the locking notches of the metal lamp socket.

6. Replace the lamp access cover.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

ONE-YEAR LIMITED WARRANTY

NYL Holdings LLC warrants the original consumer purchaser of this product that it shall be free of defects in materials and workmanship for one year from the purchase date of this product. Defects caused by tampering, improper use, unauthorized modifications or repairs, immersion in water or abuse are not covered by this warranty. If a defect covered by this warranty occurs during the warranty period, package your clock carefully and send it to the following address:

• Att: Repair center
• NYL Holdings LLC
• 1212 East Broward Bivd. Suite 203
• Fort Lauderdale, FL 33301
• 954-462-6848

You must include a Proof of Purchase, either the original receipt or a photocopy and a check or money order for USD $12.95 to cover the cost of shipping and handling. Also include your return address inside the package. NYL Holdings LLC will repair or replace the clock and return it to you. NYL Holdings LLC will not be liable for any loss or damages, including incidental or consequential damages of any kind: from any breach of warranty either expressed or implied relating to the product. Since some states do not allow the exclusion or limitation of incidental or consequential damages, these limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION :

• TO REDUCE THE RISK OF ELECTRIC SHOCK.
• DO NOT REMOVE COVER (OR BACK)
• NO USER-SERVICEABLE PARTS INSIDE
• REFER SERVICING TO QUALIFIED SERVICE PERSONEL

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION : TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

How to open a lamp door?

1. Hold a unit and two thumbs on the edge of the lamp door
2. Two thumbs press on the edge of the lamp door
3. Open a lamp door

Download PDF:Westclox Source 43000 series Big Ben Moon Beam Alarm Clock User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>