QAZQA Fimm Fan Instruction Manual

QAZQA Fimm Fan

This item contains changeable LED

1 0 2 7 13/102714
24W LED
incl. LED Board: QL7001022
220-240V~50Hz

Warning symbols

General Safety Instructions

Read this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party.
WARNING: When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury.

1. General

   • Before carrying out any work on the fan, disconnect it from the electrical supply!

   • Check if the electrical specifications of this appliance are compatible with your installation. The supplier accepts no responsibility for any physical injury or material damage resulting from incorrect use or installation of this fan.
     If you have the slightest doubt, please contact electrician.

   • Unauthorized use and technical modifications to the appliance can lead to danger to life and health.

   • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

   • Children should be supervised to ensure that they do not play with the appliance.

   • This appliance is for indoor use only.

   • Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

   • Never install the appliance in a moist or wet room.

   • Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m

   • Before pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan

   • Don’t place your arm or other object in the path of the blades, when the fan is operating.

   • Always maintain the minimum distance between the lamp and any inflammable material (curtains, wall etc), as indicated on the pictogram

   • Means for all poles disconnection having a contact separation that provide full disconnection under over voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.

   • Power supply wire from ceiling needs 1.5 sq mm wire

   • Regarding the method of the cable connection , how to assembly and the bulb type reference of a luminaire, thanks to refer to the section “INSTALLATION”

   • Warning: Before obtaining access to terminals, all supply circuits must be disconnected. “5. Appliance specification”.

   • Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

2. Electrical safety
   The appliance should be installed by authorized electrician only acc. to national wiring rules.

3. Specific Safety Rules
   The fan is to be installed so that the blades are more than 2.3 m above the floor

4. Environmental protection CAUTION!

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockiest for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Appliance specifications

TECHNICAL CHARACTERISTICS

Rated voltage| 220-240 V
Rated frequency| 50 Hz
Rated wattage| 45 W
Bulb rating| 1x24W. LED
Ambient operating temperature| 25 °C
Protection class| I
IP number| IPX0
Protective shields| N/ A

The ceiling fan (element)

PARTS DESCRIPTION

1. Safe steelier
2. J hook (For temporary hang up the fan when wiring connection
3. Mounting bracket
4. Nuts
5. Receiver
6. Remote
7. Hanger ball
8. Down rod
9. Upper canopy
10. Screws
11. Yoke cover
12. Screws
13. Cross pin
14. Cotter pin
15. Screws
16. Blades
17. Motor Housing
18. Screws
19. Motor
20. Light Kit fixing bracket
21. LED light plate
22. Screws
23. LED light kit
24. Shade
    

Installation of the ceiling fan

1. Insert down rod over upper canopy, then insert the cross pin over yoke & Cotter pin and fasten the 2 screws which fix the down rod[Fig 1)
2. Install the mounting plate by screws (Fig.2)
3. Loose the screw from motor.(Fig 3)
4. Install the blade on the motor by Screws.(Fig.4) 3
5. Make sure the fan is disconnected from the electrical supply and carefully insert the fan into the mounting bracket. Rotate the fan until the notch of the hanger ball engages the pin of the mounting bracket. Then, firmly fix the screws.Fig5)
6. Assembly the LED light plate to the light kit fixing bracket by the screws and connect the LED light kit by male & female plug. Insert the remote control receiver on the mounting bracket. Connect the motor wires, LED light wires and receiver’s power wires to the receiver by male & female plug. Also, connect the ground wire by male & female plug. Then connect the power supply with the fan.(Figó6)
7. Assembly the shade to the light plate and assembly the upper canopy to the mounting bracket. Rotate clockwise when assembling the canopy. Fig 7)
8. Now, the tan is completed.(Fig 8)

If the fan or light kit is PARTIALLY pre-assembled, you can skip the assembly procedures to next step

How to use

• Direction switch on the fan ‘s remote.(FORWARD and REVERSE switch)
• Down for summer make the air movement directly from ceiling.
• UP for winter, to circulate the warm air generated by heater to floor.
  

Remote Control Instruction

This ceiling fan can be installed with remote control, but make sure you know how to install the device in safe way or consult licensed electrician
Warranty may be affected if you install the improper remote control or install it in improper way.

1. WIRING SCHEMATIC DIAGRAM FOR RECEIVER
   Adopt RF wireless digit emission technique, biunique controlled , coincident code rate is less than one millionth.(Emitter and receiver must be sent back to factory for maintenance if damaged.)
   Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status( light and direction ) while the supply power OFF and resume to the original after reload the power supply.

2. FUNCTION INSTRUCTION OF EMITTER

3. ON/OFF the fan

4. ON/OFF the light

5. Speed of the fan (low speed–high speed)

6. Direction of the fan (reverse switch)

7. Timing control of the fan

8. LED indicated light

9. 12V battery should be used in emitter
   Notes:

10. Power on, the light on with 3500K

11. Push LIGHT ON/OFF button the 1st time, the light off

12. Push LIGHT ON/OFF button the 2nd time, the light on with 2700K

13. Push LIGHT ON/OFF button the 3rd time, the light off

14. Push LIGHT ON/OFF button the 4th time, the light on with 3000K.

15. Push LIGHT ON/OFF button the 5th time, the light off

16. KINDLY REMINDERS:

17. Learning code matching mode is used between emitter and receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “FAN ON/OFF” button for 5 seconds, it can load normally after hearing a long sound “bee”， which means learning successfully and it can works normally. (PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds)

18. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.

19. When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.

20. Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will flash out its warning when the battery get low voltage), must replace if the battery is getting low voltage.

21. Please take out the battery from the emitter when leaving unused for long time.

22. The maximum load of lighting see the above HPOWER PARAMETER LIST”
    PS please  connect the ground wire correctly, otherwise it may cause the light micro-light or flash

23. When installing the fan, the fan ceiling cover don’t press the antenna(or other wire),it is easy to breakdown the wire and short-circuited.

Disconnect from mains before maintenance or cleaning

Do not use a wet sponge to clean the appliance.

1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it cools down
2. No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3. Be sure the power is off when you clean the fan
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit

Troubleshooting

branch circuit fuses or circuit
| B/ Loose power line| breakers.
| connections to the fan.| B/ Check line wire connections
| C/ Speed controller not in| to fan
| correct position.| C/ Check speed controller’s position.
2. Fan sound noisy| A / Top canopy touching ceiling.
B/ Loose fan blade screws. C/ Ceiling fan not secured against ceiling.
D / Incorrect speed controller.| A / Lower Canopy from ceiling to ensure minimum 3 mm clearance.
B/ Re-tighten all screws on fan blades but never over-tighten.
C/ Re-tighten all screws in the hanging bracket or plate.
D / Change the controller to the one supplied.
3. Mechanical Noise| A / Allow at least for 8 hours settling-in period.|
4. Fan Wobbles| A / Fan blades are not| A / Measure from ceiling to tip
| horizontal to ceiling.| of blades, then rotate fan so all
| B/ Blade screws are loose.| blades are checked for equal
| | height from ceiling (not
| | adjustments may be made by
| | slight pressure up or down on
| | blade holders). Make sure all
| | screws are securely fastened.

DYNAMIC BLADE BALANCE KIT

PREFACE
Your ceiling fan may sometimes have wobble problem when operate due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system may cause some additional problem also bearing crooked. The following procedure to remedy such problem is strongly recommended by us from our past experience in handling the wobble problem.

Dynamic blade balancing kit for ceiling fans

1. Make sure that all blade are firmly screwed into the blade holder
2. Make sure that all blades are firmly secured the flywheel and check pitch of blade holders all must be the same
3. By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blade is out of position. A correction can be made by very gently bending the blade holder back into position
4. By the simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade slowly by hand to check the remaining blades. If blade is not in alignment, the blade holder may be gently bent up or down to be in line with the other blades

If by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit. Follow the procedure listed below:

• Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.
• Turn the fan off; select on blade place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.
• Turn the fan on, watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again. Repeat this process with all blades and then note that blade which is the most improved.
• Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the position where the clip gives the most improvement
• Next remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.
  Caution: stay clear of the blades if the clip for any reason is not secured, injury could result

Others

Have your product repaired by a qualified person
This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Please contact the store which you bought the product for after sale services if question his appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of  the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years. appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Please contact the store which you bought the product for after sale services if question

Information requirements regarding the eco-design

Description| Symbol| Value| Unit
Maximum fan flow rate| F| 64.16| m 3 / m i n
Fan power input| P| 43.50| W
Service value| SV| 1.47| ( m 3 / m i n ) / W
Standby power consumption| PSB| 0.0| W
Seasonal electricity consumption| Q| 13.92| kWh/a
Fan sound power level| LWA| 43.50| dB(A)
Maximum air velocity| c| 1.42| m/seg
| Regulation Nº 206/2012
| IEC 60879:1986
| EN 50564:2011
Measurement standard for service| EN 60704-2-7:1998
EN 60704-1:2010
| [Shall not appear all of these ones, but the same as the ones which are
| detailed in the ERP test report]

SAFETY INSTRUCTION
Please study the instruction manual and below information carefully before installing or using this product.
Please keep this user manual for further reference

1. The luminaires may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.
2. Maintenance of the luminaires is limited to their surfaces. During maintenance no moisture can come into contact with any areas of the terminal connections or voltage control parts.
3. The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution box, before any installation, maintenance or repair work is undertaken.
4. Exterior lighting must not be installed during rain.
5. Take account of the minimal separation distance from other objects and the room required around the fitting.
6. If in any doubt, consult a professional, taking local installation requirements into account. Some countries stipulate that lighting may be installed only by registered installers.
7. Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V low voltage conductors.
8. Clean with a clean, dry cloth or brush, use no solvents or abrasives. Avoid dampness on all electrical components
9. Take account of all available technical information.
10. Meaning of symbols:
    • For indoor use only, where direct contact with water is impossible
    • icon indicates the level of water-proof and dust-proof
    • Protection Class I: the fitting must be earthed
    • Protection Class II: the fitting is doubled insulated and does not require earthing
    • Protection Class Ill: the fitting is low voltage
    • Minimum distance from lighted objects (meters)
    • The type of lamp and maximum size and wattage indicated in each lighting unit must not be exceed; different items require different kind of light sources with different bulb icons
    • The armature is designed to work only with the indicated voltage. Different items require different working voltage.
    • The luminaire can be used in combination with a dimmer
    • The reference light angle and light space of the luminaire
    • This luminaire cannot be disposed together with normal domestic waste in standard rubbish can, but you have to bring it to a staging area for electrical waste
11. Take note of the symbols when connecting wires:
    

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>