weber 1530 Go Anywhere Gas Grill Owner’s Manual
- August 7, 2024
- Weber
Table of Contents
weber 1530 Go Anywhere Gas Grill
Specifications:
- Model: Weber 1530 GO ANYWHERE GAS
- Type: Gas grill
Product Usage Instructions
Assembly:
- Unbox all the parts carefully.
- Follow the step-by-step assembly instructions provided in the manual.
- Ensure all parts are securely attached before use.
Usage:
- Place the grill on a flat, stable surface away from any flammable materials.
- Connect the gas tank following the manufacturer’s instructions.
- Turn on the gas and ignite the grill according to the lighting instructions.
- Adjust the heat settings as needed for cooking.
Cleaning and Maintenance:
- Allow the grill to cool completely before cleaning.
- Regularly clean the grates and surfaces with a grill brush and mild soap.
- Check and clean the gas burners and valves periodically.
- Store the grill in a dry place when not in use to prevent rusting.
FAQ:
-
Q: How do I replace the gas tank?
A: To replace the gas tank, first, ensure the grill is turned off and disconnected from any power source. Unscrew the old gas tank and safely dispose of it. Then, connect the new gas tank following the manufacturer’s instructions. -
Q: Can I use this grill indoors?
A: No, this gas grill is designed for outdoor use only due to the risk of carbon monoxide buildup in enclosed spaces.
FOR OUTDOOR USE ONLY
This grill does not include an LP fuel tank.
Check Package Contents
You should have received the parts listed below. While we give much attention
to out product, unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call Weber- Stephen Products Customer
Service Center toll free 1-800-446-1071
to receive immediate assistance.
Install Legs
Place washers on leg ends and insert ends into holes in bottom unit. Be
careful not to scratch the porcelain finish while installing the legs. Repeat
with other leg.
Install Leg Lock
Position curved end of leg lock at corner of the straight portion of the leg,
as shown. Push until it snaps on.
Position legs and secure leg lock
Swing legs around so that the rounded part sets on the ground and the bottom
of the cooking box rests on the straight part of the legs. To lock the legs in
place turn the leg lock around clipping it over the opposite leg. (Unlock the
legs by unlatching this clip in the reverse direction.)
Install Burner Tube
From the inside, insert burner tube through the large hole in the side of the
bottom unit. Line up the other end of the tube with the hole. Insert the 1/2
inch bolt. Add the washer and wing nut. Tighten.
Install Regulator
Remove the retaining clip from the regulator. Attach regulator assembly by
inserting the brass fitting into the end of the burner tube.. Secure regulator
assembly by installing the retaining clip in the square openings on both sides
of the burner tube.
Install Igniter
Insert the igniter electrode and two 10-24 screws through the igniter bracket and the holes in the bottom unit on the side opposite the regulator.
Add washers and wing nuts, making sure that the wing nuts are secured in a vertical position.
The igniter electrode has been pre-bent. It may need to be adjusted so the tip is approximately 1/8 inch from the holes in the burner tube.
DANGER
Make sure the tip of the igniter wire is adjusted to the holes in the
burner tube. If it is not adjusted properly, gas can accumulate in the
barbecue while igniting the barbecue. Delayed ignition of the accumulated gas
may occur. This will result in a fire or explosion which can cause serious
bodily injury or death, and damage to property.
Install Flavorizer Bar
Place the Flavorizer Bar in bottom unit, covering the burner.
Install Cooking Grate
Set the cooking grate onto the recessed edge of the bottom unit.
To Secure for Transport
Put the lid on the bottom unit unlock legs and pivot them into the locked
position up over the projections on the lid.
To Use
Pivot legs under grill and lock legs. The hooks on the inside of the lid allow
it to rest on the edge of the bottom unit.
Read important DANGERS, WARNINGS and CAUTIONS in Owner’s Guide before operating this barbecue.
Connecting the Cylinder
- Lubricate the threads of the regulator assembly with petroleum jelly.
- Make sure the burner control valve is in the LOCK/OFF position before attaching the propane cylinder. Valve closes by turning the knob clock-wise to the LOCK/OFF position.
- Attach the propane cylinder to the grill by pushing the cylinder slightly while turning clockwise into the regulator. Turn until a snug fit is obtained.
Check for Gas Leaks
DANGER
Do not use an open flame to check for gas leaks. Be sure there are no
sparks or open flames in the area while you check for leaks.
This will result in a fire or explosion which can cause serious bodily injury
or death, and damage to property.
- Check the connection between the tank and the regulator for gas leaks. Mix a couple of tablespoons of liquid detergent with an equal amount of water.
- Be sure to leave the burner control valve in the LOCK/OFF position. Wet the connection with the soap solution and watch for bubbles. If bubbles form or if a bubble grows, there is a leak.
- If there is a leak, check the fitting, make sure it is tight, recheck the connections.
- Check for gas leaks each time you disconnect or connect the gas supply
Lighting Your Gas Grill
WARNING: Always remove the lid before lighting your grill.
- Push down the burner control valve and turn counter-clockwise to HIGH.
- Hold the handle of the bottom unit while pushing the igniter button 2 or 3 times.
- Check to see if the burner is lit by looking through the viewing hole in the Flavorizer Bar.
WARNING: If burner does not light, turn burner control valve OFF, wait 5 minutes for the gas to clear, then try again.
Manual Lighting
- Light a match and hold it in one of the four holes in the bottom of the grill.
- Push down burner control valve and turn counter-clockwise to HIGH.
- Check to see if the burner is lit by looking through the viewing hole in the Flavorizer Bar.
WARNING: If burner does not light, turn burner control valve OFF, wait 5 minutes for the gas to clear, then try again.
Gas Grill Care
While lid is warm, wipe inside with paper towels to prevent grease build-up.
After cooking, burn grease residues off by turning burner control valve to
HIGH for several minutes with the lid in place.
It is not necessary to wash cooking grate after each use. Simply loosen
residue with a brass bristle brush or crumpled aluminum foil. Then wipe with
paper towels.
Thoroughly clean your gas grill at least once a year.
-
Remove cooking grate and Flavorizer Bar.
-
Remove tubular burner before cleaning (refer to assembly instructions)
To remove: Take out retaining clip and remove regulator assembly.
Remove wing nut, washer and bolt (on opposite end inside unit). Lift tubular burner up and slide out of grill. -
Wipe out with paper towels and wash with a mild detergent and water.
Rinse well. Wash Flavorizer Bar and cooking grate with warm soapy water. Rinse, then wipe dry with a paper towel. -
Reinstall tubular burner, Flavorizer Bar, and cooking grate.
-
Check for gas leaks before operating.
- 1-3. Handle
- 4. 10-24 Wing Nuts
- 5. Retaining Clip
- 6. Regulator Assembly
- 7. Leg Lock
- 8. Lid
- 9. Cooking Grate
- 10. Flavorizer Bar
- 11. Bolt
- 12. 5/16” Flat Washer
- 13. 1/4-20 Wing Nut
- 14. Machine Screw
- 15. Burner Tube
- 16. Igniter
- 17. Legs
- 18. Flat Washer
- 19. Bottom unit
©1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks of Weber- Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A.
References
- Repair Your Grill: Shop Replacement Parts for 24,880 Models
- Weber Grill Parts - Select From 2037 Models
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>