ecler eSAM702 Installation Analogue Mixer User Manual
- June 3, 2024
- ecler
Table of Contents
eSAM702 Installation Analogue Mixer
User Manual
eSAM702 Installation Analogue Mixer
IMPORTANT REMARK
WARNING: SHOCK HAZARD – DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is
ntended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING (If applicable): The terminals marked with symbol of “ ” may be
of sufficient magnitude to constitute a risk of electric shock. The external
wiring connected to the terminals requires installation by an instructed
person or the use of ready-made leads or cords.
WARNING: To prevent fire or shock hazard, do not expose this equipment to
rain or moisture.
WARNING: An apparatus with Class I construction shall be connected to a
mains socket-outlet with a protective earthing connection.
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug the apparatus during lightening sorts or when unused for long periods of time.
- Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket. For this reason, it always shall remain easily accessible.
- Equipment is connected to a socket-outlet with earthing connection by means of a power cord.
- The marking information is located at the bottom of the unit.
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
WARNING: This product must not be discarded, under any circumstance, as
unsorted urban waste. Take to the nearest electrical and electronic waste
treatment centre.
NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be
caused to people, animal or objects due to failure to comply with the warnings
above.
IMPORTANT NOTE
Thank you for choosing our Ecler Installation Analogue Mixer eSAM702!
It is VERY IMPORTANT to carefully read this manual and to fully understand its
contents before any connection in order to maximize your use and get the best
performance from this equipment.
To ensure optimal operation of this device, we strongly recommend that its
maintenance be carried out by our authorised Technical Services.
Ecler eSAM702 comes with a 3-year warranty.
INTRODUCTION
The eSAM702 is an easy-to-use professional mixer designed for PA applications. Its main features are:
- 6 MIC/LINE STEREO input channels.
- 1 seventh STEREO LINE input channel
- Balanced main stereo output
- Adjustable microphone sensitivity on the back panel.
- +18 V DC Phantom power supply available for all “MIC” inputs.
- Includes assignable Talkover on inputs 1 to 6 (the Talkover function may be simultaneously enabled on one, two or all entries).
- Global 3-band tone controls, adjustable with a screwdriver.
- 3 LED level indicators per channel for the stereo mix signal.
- Main output level control.
- Record output.
- The “MUTE” remote control input allows connection of external dry contact closures (fire detection systems and other safety devices that have to mute the mixer signal by activating the “NO” (normally open) control signal)).
- Mono/stereo selector for the main mix output.
INSTALLATION
The eSAM702 mixer has been specially designed to be installed in a standard
19″ rack, taking up 1U. It has been designed to be operated by non-technical
users. This is the reason why its tone controls are adjustable only with a
screwdriver. On the opposite, input and output level controls use classic and
easily accessible rotary knobs.
Due to its low power consumption and heat sink, the eSAM702 doesn’t need any
fan cooling. However, avoid installing it in dusty environments and/or in a
location with extreme temperature and moisture.
The mixer should be kept apart from noise and interference sources (dimmers,
motors, etc…) as well as from power cables.
The eSAM702 is powered by alternating current through its external power
supply: 100240 VAC and 50-60 Hz. This external PSU has interchangeable
connectors: American, European, British and Chinese.
In order to protect the mixer from eventual overloads, the eSAM702 is
protected by a timered power fuse of 0.5A. If it gets blown up, you must
replace it with an identical one. If it gets blown up, you must replace it
with an identical one. NEVER REPLACE THE FUSE WITH ANOTHER ONE WITH A HIGHER
VALUE.
CAUTION: Fuse substitutions have to be performed by a qualified
technician.
INPUTS
The eSAM702 supports two types of audio signals for each of its first 6
inputs (mono MIC or stereo LINE), selectable by a MIC/LINE switch on the rear
panel:
Microphone signal: 6 mixing channels offer a Euroblock connector for a
nominal input level from –50dBV (3.16mV) to –20dBV (0.1mV), with a GAIN
control on the rear panel to adjust the gain.
Here is the wiring diagram for microphones: 
Microphones must be low impedance
(200 to 600) and monophonic.
The eSAM702 supplies phantom power for condenser microphones; it is enabled by
an internal jumper (see diagram). By default, phantom power is disabled
(factory setting).
The Talkover (priority) function operates when a signal is detected at the
inputs 1 to 6 this function is assigned to; it attenuates the other inputs of
the unit that don’t have
priority. Turn it on/off for each input channel with the “TK” switch on the
front panel.
To manage the important level differences existing between conventional CD and
LINE sources and other devices capable of producing audio signals, the LINE
inputs 1-6 of the eSAM702 are standard line inputs (0dBV) and the sensitivity
of the LINE input #7 can be selected (0/-6dBV) by internal jumper (the default
position is 0dBV). A sensitivity of 6dBV is ideal for low-level sound sources
such as media players, portable MP3 players, tablets, computers, mobile
phones, etc.
WARNING: Turntables CAN NOT be directly connected to this unit, because
eSAM702 has no RIAA preamp equipped input.
OUTPUTS
The eSAM702 has a main stereo output (OUT L / OUT R), with electronically
balanced Euroblock connectors.
Connection is made according to the following diagram: 
The mixer’s main output level (OUTPUT VOL) must be set in order to
avoid your system power amp clipping indicators (CLIP) to be permanently lit.
Only the most powerful lower frequencies must light them.
Other connections on the back panel:
- AUX/REC output with a nominal output of 0dBV (10k load) and an extra gain setting of +6dB, enabled by internal jumper (0dBV is the default position).
- L+R switch: convert output signals in a mono signal.
- MUTE remote control input: enabled by external dry contact closure. It allows connection of fire detection systems and other safety devices that have to mute the mixer by using this control signal. The mode of operation is “NO” (normally open).
STARTING UP
This is directly done via the POWER mains switch. Even is the power-up noise
of eSAM702 is minimal, we highly recommend to power up all equipment in the
following order: sound sources, mixing units, equalizer, processors and
finally power amplifiers. The power down sequence is the inverse of the power
up one.
EQUALIZATION
The tone controls of the main output provide a ± 15dB gain/attenuation for
each of the bands, and their central operating frequencies are 100Hz, 2kHz and
10kHz. Given the philosophy of this unit, the tone controls are designed to be
adjusted with a screwdriver, thereby preventing accidental manipulation during
normal use.
VU-METER
The eSAM702 has a VU-meter to show the main mixing signal.
GROUND LOOPS, BACKGROUND NOISE
You should always make sure that the signal sources coming to the unit, as
well as all devices connected to its outputs, do not have their grounds
interconnected, that is; ground must never come from two different devices.
Should this ever happen, noises could occur and seriously interfere the sound
quality.
Cable shields, when connected to the chassis, must never be linked together.
This will avoid ground loops.
The eSAM702 mixer was designed to produce the lowest background noise.
Independently from the electronic design, the resulting background noise
directly relies on the correct use and installation of the mixing unit.
Adjust, where appropriate, the gain of each input for an adequate operating
level and then adjust the VOL controls on the front panel to obtain the
desired input mix. Finally,
adjust the VOL control of the main mix output to get the relevant output
volume for your installation, and also enable the TK switches for priority
inputs (a signal detection on these priority inputs will attenuate the signal
of non-priority inputs).
Important note on mix level adjustment: setting for example a channel VOL
control to “2” and the output VOL control to “10” is not the same as the
opposite. In the first case, the signal entering the mixing amplifier is weak,
but even so it contains a background noise, so the signal/noise ratio is low
(low signal). When the output amplifier equally amplifies both parts as a
whole, the output has a very high background noise. In the second case, as the
channel VOL control is set to the maximum, the signal received by the mixing
amplifier has a high level and therefore also a high (good) signal/noise
ratio, so when this signal reaches the output VOL control and is amplified,
the signal/noise ratio remains better than in the previous case.
CLEANING
The front panel should not be cleaned with dissolvent or abrasive substances
because silk-printing could be damaged. To clean it, use a soft cloth slightly
wet with water and neutral liquid soap; dry it with a clean cloth. Be careful
that water never gets into the unit through the holes of the front panel.
DIAGRAMS and FUNCTION LIST 
| 1 Channel volume control, VOL | 12 Line input, LINE |
|---|---|
| 2 Talkover switch, TK | 13 Input sensitivity adjust, ADJ |
| 3 Bass control, BASS | 14 Recording output, AUX/REC |
| 4 Midrange control, MID | 15 Mono-stereo switch, L+R |
| 5 Treble control, TREBLE | 16 Main output, left channel, OUTPUT L |
| 6 Output main volume control, OUTPUT VOL | 17 Main output, right channel, |
OUTPUT R
7 LED indicator, MUTE| 18 Screwable terminal for remote mute, MUTE
8 LED indicator, POWER ON| 19 Mains socket
9 Led Vu-meter, LEVEL| 20 Fuse holder
10 Micro input, MIC| 21 Mains switch, POWER
11 Micro line selector| 1
CONFIGURATION DIAGRAM
BLOCK DIAGRAM
TECHNICAL CHARACTERISTICS
Inputs Sensitivity (*) / Impedance
LINE (1-6) LINE 7| OdBV / 50k0 -6dBV• / 50k0
Input sensitivity adjust
MIC 1-6 BAL MIC/LIN 1-6| 35dBV/>1.k.0 ±15dB
Outputs Level/ Minimum load
OUT AUX/REC| 0(+6)dBV */ 6000 OdBV/10k0
Frequency response
UNE MIC BAL| 10Hz-50kHz – 1dB
10Hz-30kHz – 1dB
Harmonic distortion
UNE MIC BAL| <0.00596dB <0.04%dB
CMRR
MIC I >60dB@lkHz
Signal / Noise ratio
UNE MIC BAL| >110dB >85dB
Tone control
BASS MID TREBLE| 100Hz ±15dB 2kHz ±15dB 10kHz ±15dB
Talkover
TIME EFFECT| 2 sec -30dB
Phantom voltage| +18VDC
DC supply| ±17,5 VDC
Mains| 100-240VAC + External PSU 17,5VDC
Power consumption| 16VA
Dimensions
Panel Depth| 482,6x44mm 120mm
Weight| 1,8kg
All product characteristics are subject to variation due to production
tolerances.
NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements
in the design or
manufacturing that may affect these product specifications.
For technical queries contact your supplier, distributor or complete the
contact form on our website,
in Support / Technical requests.
Motors, 166‐168 08038 Barcelona ‐ Spain ‐ (+34) 932238403
information@ecler.com
www.ecler.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>