VEVOR Multifunctional Digital Heat Press Machine User Guide

VEVOR Multifunctional Digital Heat Press Machine

Heat Press Machine Parts Introduction

Parts List

Assembly & Use Steps

Rotate the heat transfer board to the side.

Pull out the mat below, place the clothes flat on the mat, and place the pattern on the clothes.

Turn this adjustment switch to adjust the pressure.

Intelligent temperature controller operation method

Preparation before Using:

1. Check the connection between the power plug and the electrical socket of the electrical cabinet. Be sure to operate with safe ground wire!!!
2. The heat press element must be securely plugged into the machine before you switch the machine on. Plug your electrical cord into the machine. Plug the electrical socket into the wall plug. Turn the power on by flipping the On/Off Switch on.( Nominal voltage:220V, Max.input power:1250W )

Set temperature required

Set the temperature and time according to the table below and get the specific corresponding temperature and timing setting. (Temperature is measured in Degrees Fahrenheit.) Press the “MODE” button ONCE, and see the “set light” turning red. Then press the “plus/minus key” to set the initial heating temperature.

Press Object| Initial Temperature| Highest Temperature| Proper Heating Time ( s )
---|---|---|---
Mugs| 230| 330| 40
Tiles| 230| 330| 40
Metal Board| 230| 300| 40
Plate| 230| 355| 150

T-shirt

|

230

|

355

| Sublimation paper:30-50s
T-shirt Paper:10-20s

A.Initial Temperature Setting ( Range:200-450℉)

Press the “MODE” button ONCE, and see the “set light” turning red. Then press the “plus/minus key” to set the initial heating temperature.

B.Highest Temperature Setting ( Range:200-450℉)

Press the “MODE” button for THE SECOND TIME; see the “temperature light” turning red. Then press the “plus or minus key” to set the highest heating temperature.

C.Proper Heating Time Setting ( Range:0-999 sec.)

Press the “MODE” button for THE THIRD TIME; see the “time light” turning red. Then press the “plus or minus key” to set the proper heating time.

D.Finish the Setting and Stands by to Work

Press the “MODE” button for THE FOURTH TIME; finish the setting , The set light is on, and the temperature will continue to rise. When the set maximum temperature is reached, the countdown starts. After the countdown ends, the “BEEF” sound will be emitted, the indicator light will turn off, and the operation is complete. and the machine will stand by to work.

Turn off the power and pull out the mat. It is recommended to wear heat- resistant gloves when removing clothes or remove them after 2-3 minutes. Be careful of hot heat.

Note

• The machine has a self-locking function for temperature setting
  • If the starting temperature is set to 340°F, the machine will automatically limit the maximum temperature setting range from 340 to 430°F.
  • Conversely, if setting the maximum temperature as 250°F at first, the machine will automatically limit the starting temperature setting range from 200 to 250°F.
• Initial heating temperature always= <Highest heating temperature

Replace the Baking Tray Mat

Rotate the heat transfer board to the side

Select the appropriate size baking pan mat ( Part A or B )

Rotate the heat transfer board to the side

Replace the Baking Cap Mat

Slide the baking mat ( Part D ) in

Use the screwdriver 4 to tighten the 2 screws removed and put the cap on.

Replace Baking Coaster

Printing methods

1. Adjust pressure to your requirement (Neither too tight nor too loose), Plug in the power cord, and turn the power switch ON.
2. The temperature starts to rise. Set the Initial temperature, Highest Temperature, and press time.
3. Once the temperature rises to the Initial temperature, the buzzer will send out a shot “BEEF” sound.
4. Press the button once. Then Place the object (i.e. T-shirt) on the press bed. Pull down the handle to press the object.
5. Wait for the time to end up with a long buzzer sound. ( Note: There will be about 5s time for a long buzzer to notify you it has finished, and after that will appear 5s for a short buzzer to notify you whether you still going to the next work, if not the temperature will fall to the Initial temperature ) Work finish and take out the object.
6. Turn off the power switch.

Troubleshooting for transfer quality

1. Pale Color: The temperature is too low/the pressure is not correct/or not pressed long enough.
2. Blurring Pattern: Too much transfer time causes proliferation.
3. Part Blurring of Pattern: Heat was not distributed correctly through the heat plate. Allow more time between press operations. Pressure distribution can also be the cause, which can be set on the four plate surface adjusters. Please note that it has been factory set and there should be no need to adjust them.
4. Dull Surface of Pattern: The pressure is too low or the temperature is too high.
5. Scarred Pattern: Transfer time is too long.
6. Different Pattern Color: The pressure is incorrect or the transfer paper is poor quality.
7. Adhesive Paper: The temperature is too high or poor printing ink.

CAUTION

• CHECK the correct voltage before using the machine. Be SURE to operate with reliable grounded protection connections.
• TURN OFF the machine, and then DISCONNECT the power supply before replacing the heat units. DO NOT forget to wear insulated gloves if the unit is still under high temperature.
• AVOID prolonged burning of the heating parts. If not turning the power off, please place a hot stamping replacement ( it could be a scrap and can be used repeatedly ).AVOID damaging the heating units with sharp parts of the stamping object.
• AVOID touching the heating units and the compression spring without protection in case of potential damage,  to the body during use.
• If it’s hard to push the grasp, please adjust the rotation lock screw to reduce the pressure of the compression spring. Or, it will damage the strength of the machine.
• Before lifting the machine, please lock the machine head with the rotation lock screw and loosen the handle(don’t screw the rotation lock screw too tight). Besides, do not put down the machine beyond the limit. When meeting the falling limit, you can feel an obvious
• pressure on the swiveling pressure adjustment wheel.
• Keep children away from the machine!!!
• DO NOT attempt to press products that are not intended for normal heat transfer. Baking pads should be avoided empty burning.

FAQs

What is the VEVOR Multifunctional Digital Heat Press Machine?

The VEVOR Multifunctional Digital Heat Press Machine is a versatile device used for heat transfer applications, allowing you to customize and print designs on various surfaces.

What types of materials can the VEVOR Digital Heat Press Machine work with?

The VEVOR Digital Heat Press Machine is designed to work with a range of materials, including fabrics, ceramics, metals, and more, making it suitable for different printing projects.

Is the heat press machine easy to operate?

Yes, the VEVOR Digital Heat Press Machine is typically user-friendly, with intuitive controls and a digital display, making it easy for beginners and experienced users alike.

What is the maximum temperature it can reach?

The VEVOR Digital Heat Press Machine often has a maximum temperature range, commonly reaching temperatures high enough for various heat transfer applications, such as sublimation printing.

Can it handle different sizes of materials?

Yes, the VEVOR Digital Heat Press Machine usually comes with adjustable settings to accommodate different sizes of materials, allowing for flexibility in your printing projects.

What safety features does the VEVOR Digital Heat Press Machine have?

Many models of the VEVOR Digital Heat Press Machine include safety features like an auto-shutoff function and heat-resistant handles to ensure safe and efficient operation.

Is the pressure adjustable on the heat press machine?

Yes, the VEVOR Digital Heat Press Machine typically features adjustable pressure settings, allowing you to customize the pressure according to the requirements of your printing job.

What printing techniques can be used with this heat press machine?

The VEVOR Digital Heat Press Machine supports various printing techniques, including heat transfer, sublimation, and more, providing versatility for different applications.

Can it be used for commercial purposes?

Yes, the VEVOR Digital Heat Press Machine is suitable for both personal and commercial use, making it a valuable tool for businesses and DIY enthusiasts.

What is the warranty coverage for the VEVOR Digital Heat Press Machine?

Warranty coverage may vary, so it's recommended to check the manufacturer's or retailer's warranty information for specific details and terms related to your purchase.

Is the VEVOR Digital Heat Press Machine portable?

Portability may depend on the specific model, but some versions of the VEVOR Digital Heat Press Machine are designed with portability in mind, featuring a compact and lightweight design.

How can I troubleshoot issues with the VEVOR Digital Heat Press Machine?

In case of any problems, refer to the user manual for troubleshooting guidance, and if needed, contact VEVOR customer support for assistance.

Video- VEVOR Multifunctional Heat Press

Download this PDF Link:VEVOR Multifunctional Digital Heat Press Machine User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>