PROGRESS LIGHTING P500456-31M 87 Inch Matte Black Convertible Pendant Ceiling Light Instruction Manual

PROGRESS LIGHTING P500456-31M 87 Inch Matte Black Convertible Pendant

Ceiling Light

PACKAGE CONTENTS

HARDWARE CONTENTS

HARDWARE CONTENTS (not actual size)

Safety Information

• Please read and understand this entire manual before attempting to assemble, operate or install the product. CAUTION: Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.
• CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
• WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
• CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

• Shut off the main power supply before cleaning the product or changing light bulbs.
• To clean, wipe with a damp cloth.
• Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

• Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. You now need to adjust the screw length according to the fixture canopy depth.
• Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
• Lift up the fixture and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 5 and step 10.
• Next, take the fixture down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.

Ceiling Assembly Instructions

• Pass the wires through the stem (E) and out of the canopy (F). Thread the stem (E) into the fixture (A) securely. Thread the canopy (F) into stem (E).

• Wearing gloves, Align the holes on the glass panel (8) with the holes on the frame of fixture (A) , and use the rubber washer (C) and screw (D) to secure them tightly.

• Strip 3/8″ of insulation from the electrical wire ends. Using a wire connector (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire from the outlet box.

• Connect the fixture ground wire and supply ground wire using a wire connector or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.

• Attach canopy (F), two-cylinder nuts (EE) to screws (AA). Tighten cylinder nuts (EE) to secure the fixture to the ceiling.

• Thread lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent candelabra base lamps, SBCFL or SBLED.

Hanging Assembly Instructions

• Remove hex nut & lock washer inside the canopy (F) to remove the pre-installed coupling (Fl). Discard the coupling (F1) for the hanging version.
• Install the loop (GG) onto the canopy (F) with the hex nut & lock washer previously removed. Tighten securely.

NOTE: During this step, determine the hanging length of your fixture by removing pipes and chain links. The electrical and ground wire may also optionally be cut to length.

• Do NOT cut electrical or ground wires until this length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy chain loop to allow for easy connections in step 10.
  (Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.)

• Pass wires through coupling (Fl), attach coupling (Fl) to the stem (E) and secure tightly.

• Once the hanging length is determined, pass wires through pipes (JJ)/(KK) and nipples (LL), tightening stems to assembly as you go to avoid twisting the wires.

• Pass wires through chain loop (GG) and tighten chain loop (GG) to stem assembly (JJ).

• Open chain link at one end of chain (FF). Hook the open chain link (FF) onto the chain loop (GG), and Close the chain links back together with the pliers. Open the quick link (HH), and hook the quick link (HH) onto the other end of the chain (FF) and the canopy chain loop (F). Close the quick link (HH) and secure it tightly.

• Continue to weave the wires through the chain links (FF) and up through the canopy loop (F)

• Strip 3/811 of insulation from the electrical wire ends. Using a wire connector (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire from the outlet box.

• Connect the fixture ground wire and supply ground wire using a wire connector or by fastening to the ground screw on the round mounting plate. Push all wire connections into the outlet box.

• Attach canopy (F), two-cylinder nuts (EE) to screws (AA). Tighten cylinder nuts (EE) to secure the fixture to the ceiling.

• Thread lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent candelabra base lamps, SBCFL or SBLED.

WARRANTY

WARRANTY AND EXCLUSIVE REMEDY: Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at the time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. The customer’s sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at the time of shipment. Progress’s sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE, WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers? Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain the customer’s responsibility. The customer is responsible for determining the suitability of our products for the customer’s use or resale, or for incorporating them into objects or for applications that the customer designs, assembles, constructs or manufactures.

Assembly and Installation Instructions
Caution: Read the instructions carefully and turn off the power at the central circuit breaker before starting the installation.

• CAUTION: Read instructions carefully and turn off power at the central circuit breaker before beginning installation.
• WARNING: Fire hazard. Min 90°C power conductors. Consult a qualified electrician to secure the branch circuit conductor.
• WARNING – If there are other regulating mechanisms used with this device, carefully follow instructions to meet NEC requirements. If you have any questions, consult a qualified electrician.
• CAUTION – Glass is always fragile; Handle the component(s) and/or bulb(s) with care.

CONTACT

THANK YOU for selecting Progress Lighting

• We can assist you with questions regarding product information, assembly, or missing parts
• 800-447-0573 8 am-8 pm (Eastern), Monday-Friday
• customerservice@progresslighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>