Volente Flipper Kit Installation Guide
- July 29, 2024
- Volente
Table of Contents
Volente Flipper Kit
Product Specifications
- Product Name: VolenteFlipperKit
- Model Numbers: 58.817, 58.818
- Adjustment Range: 300-400
Product Usage Instructions
Pre-Installation Checks
- The product size and adjustment are suitable for the installation site.
- Check that all parts are present by referring to the packing list and product schematic diagram.
- Ensure you have all the required tools listed in the manual.
Installation Steps
- Fit seal B onto the end of the flipper panel with the cam hinge.
- Place the end of the flipper with the cam hinge into the extrusion on the end of the main screen.
- Tighten the grub screw in the bottom hinge while the flipper screen is in a straight line.
- Fit top hinge C while the screen is in a straight line.
- Check that the bottom rise and fall hinge is operating correctly when the flipper is moved.
Silicone Sealing
Use a silicone gun to apply silicone as illustrated, ensuring that silicone sealant is applied only on the outside.
FAQ
Q: Can I install the VolenteFlipperKit myself?
A: This product should only be fitted by a fully qualified installer to ensure proper installation and safety.
Q: What should I do if there are missing parts or damage?
A: Any missing parts or damage must be reported to your supplier within 10 days of purchase and before installation to address any issues promptly.
MODELS
Volente Flipper Kit
| 58.817 | Adjustment |
|---|
300
58.818| 400
- This product should only be fitted by a fully qualified installer.
- This product must be unpacked and checked for quality prior to installation.
- Any missing parts or damage must be reported to your supplier within 10 days of purchase and before install.
- No claims can be enforced outside of these terms.
TOOLS REQUIRED
LIST OF SPARE PARTS
- Please make the following checks before connecting the installation:
- The product supplied is the required size and the adjustment is compatible with the site situation.
- Check all component parts are present, see packing list and product schematic diagram for reference.
- Make sure you have all the required tools.
PRODUCT SCHEMATIC DIAGRAM
- Fit bottom hinge D onto profile A with screws K.
- Bond profile A with bottom hinge D attached to existing Valliant walk-in panel with clear silicone.
- Ensure enough silicone is used to completely bond the profile to the glass. Clean off any excess immediately.
- Ensure the profile is installed with the correct tolerance to allow the top hinge to fit into position.
- Fit seal B onto the end of the flipper panel with the cam hinge.
- Place the end of the flipper with the cam hinge into the extrusion on the end of the main screen.
- Tighten the grub screw in the bottom hinge whilst the flipper screen is in a straight line.
- Fit top hinge©whilst screen is in a straight line.
- Check bottom rise and fall hinge is operating correctly when the flipper is moved.
- Silicone as illustrated ensures silicone sealant is on the outside only.
- Eastbrook Road, Gloucester GL4 3DB
- Technical Helpline: 01452 317890
- email: technical@eastbrookco.com
- Cleaning and Maintainence of Shower Enclosures
- Do not clean the shower enclosure with irritant detergents such as alcohol, bleach, or other chemical cleaners.
- Only clean with mild soapy water or a propriotory cleaner where the label advises it is suitable for the materials the enclosure is constructed from, test on a small area first.
- For treating limescale we would recommend distilled vinegar in a half and half solution with water.
- Following installation should you find that there is a notable noise when the glass door moves you may add a small amount of silicone lubricant onto the roller wheels and tracks, hinges, or clips.
- It is the responsibility of the product owner to maintain the product as recommended above. Also, check for parts that have broken or become loose to protect against failure of the enclosure.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>