VESTLAND Sit Stand Corner Electrically Adjustable Ergonomic Desk Installation Guide

VESTLAND Sit Stand Corner Electrically Adjustable Ergonomic Desk

Specifications

• Height Range: 71cm(28) – 118cm(46)
• Travel Speed: 30mm(1.2) per second
• Weight Capacity: 100KG (220lbs)
• Duty Cycle: 10%, Max. 2 mins on, 18 mins off
• Memory Presets: 3
• Soft Start/Stop
• Adjustable Leveling

Product Usage Instructions

Installation

1. STEP 1 : Checklist A x2, D x2, M-A x8, M-D

Advanced Setting

To access advanced settings, press the S button for 5 seconds until the LED flashes. Follow the on-screen instructions to navigate through the menu and make adjustments.

Programming Instructions

1. Memory Settings : Save up to four desk heights for quick recall using the handset.
2. Handset Lock : Lock the handset to prevent accidental desk movements or setting changes.

Troubleshooting

If your desk is unresponsive or displays error messages, ensure all cables are securely connected. If issues persist, follow the reset procedure provided in the manual.

Frequently Asked Questions

Q: How do I adjust the height settings?

A: Use the UP or DOWN button to move the desk to the desired height, then press the corresponding number button to assign that height to a memory preset.

Q: What should I do if the desk does not respond?

A: Check all cable connections and perform a reset if needed as outlined in the troubleshooting section.

• Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.
• CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• IMPORTANT: Ensure that you have received all parts according to the component checklist before installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
• MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Checklist and Installation

Screw List

Installation video

Scan the QR code for the installation video ****

INSTALLATION INSTRUCTION

TECHNICAL SPECIFICATIONS

ADVANCED SETTING

• Press the “ S ” button for 5 seconds until the LED ashes. The menu contains 7 items as the table.
• press the “ S ” button to select the item you’d like to set, then use the buttons to adjust the value.
• Long press the “ S ” button to save the setting and a progress bar app will be displayed if it is saved successfully and “FAL” will be displayed if it fails. The menu will return to the display height automatically if no operation within 10 seconds.

PROGRAMMING INSTRUCTIONS

MEMORY SETTINGS

Save up to four commonly used desk heights and recall them quickly

• Use the UP or DOWN button to move the desk to the desired height.
• Press the “S” button.
• Press the “1, 2, or 3” button to assign the current height to a number on the handset.
• To bring the desk back to any of those assigned heights, press the numbered button.

HANDSET LOCK

• The handset can be locked to prevent accidental activation or movement of the desk and to prevent desk settings from being accidentally changed by children or coworkers
• TO LOCK: Press and hold the buttons simultaneously for 5 seconds until the LED reads “Loc”.
• TO UNLOCK: Press and hold the “UP” and” Down” buttons simultaneously for 5 seconds until the LED switches from “Loc” to the height display

TROUBLESHOOTING

If your desk does not respond when you try to raise it or lower it, or if the handset displays error messages, check to make sure all the cables are secure(Legs to cables, cables to Control box). If the problem persists, perform the reset procedure below.

RESET PROCEDURE

1. Unplug the power cord and hold the “ S ” button on the Handset for 30 seconds.
2. Plug the power cord back in.
3. Hold the button until the desk reaches its lowest height, then release it. Hold the button again for about 10 seconds until the desk lowers a bit more, then slightly rises and stops then releases.
4. The handset will then display the current height, and you should be able to operate the desk.
5. You may also need to do this if the desktop is ever unplugged or loses power.
   • If the error message persists after performing the Reset procedure, contact us or local distributors to get support.

the Control Box
Abnormal Power Supply Board| SC1| Power on again. If the code persists, replace the Control Box
Abnormal Memory| SC2| Power on again. If the code persists, replace the Control Box
Abnormal Sensor| SC3| Power on again. If the code persists, replace the Control Box
Collision Protection by Sensor| R-2| The desktop will stop and retract 5cm(2”)
Overheated| HOT| Let the desk rest for 18 minutes
CommunicationaFilure| R-5| Check the connection between the Handset and the Control Box or replace the Handset
Abnormal Voltage| R-6| Power on again. If the code persists, replace the Control Box
Mechanical failure| R-8| Perform the Reset procedure. If the code persists, replace the Leg
Rest not completed| RST| Perform Reset procedure
Short Circuit| EX0| Power on again. If the code persists, replace the Control Box
Overload| EX1 Re| duce the load on the desk
Motor Open Phase| EX2| Perform the Reset procedure. If the code persists, replace the Leg
Wrong Running Direction| EX3| Perform the Reset procedure. If the code persists, replace the Leg
Collision Protection| EX4| The desktop will stop and retract 5cm (2”)
Motor Stalling| EX5| Perform the Reset procedure. If the code persists, replace the Leg
Disconnections of Motor Cabl| e EX6| Check the connection between the leg and the control box
Remarks : X means 1(the first leg), 2(the second leg), 3(the third leg)

• In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary (see Reset Instructions above)
• This product is designed with a duty cycle of 10% (2 min. On, 18 min. off)
• Keep Children away from electric height-adjustable desks, control units, and handsets. There is a risk of injury and electric shock
• Do not open any of the components: lifting columns, control box, or handset.
• There is a danger of electric shock
• Keep all electrical components away from liquids

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>