Starlink SYS X1271 4G Wireless Data Terminal User Manual
- July 26, 2024
- Starlink SYS
Table of Contents
- Starlink SYS X1271 4G Wireless Data Terminal
- Product Information
- Product Usage Instructions
- Product Manual Overview
- Description of Product Appearance Information
- Equipment Quick Installation Guide
- Equipment Management
- Introduction to Basic Functions
- Specifications
- FCC regulation
- FAQ
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Starlink SYS X1271 4G Wireless Data Terminal
Specifications
- Model : X1271
- 4G Wireless Data Terminal CAT12 cloud card solution
Product Information
Product Appearance
The product features ports for SIM, WAN/LAN, LAN, DC power, and external
antennas. It has a reset key, power button, and WPS keys.
Light Position Description
Name | Status | Description |
---|---|---|
POW Light | Green Light Off/On | Indicates device power status |
NET Light | Green Light Off/On | Indicates data connection status |
SMS/WPS Light | Green Light Off/On/Flashing slowly | Indicates wireless |
connection and WPS button status
4.5G Light| Green light flashing fast (0.1s: 0.1s=On: Off)| Indicates 4.5G
network status
Product Usage Instructions
Equipment Quick Installation Guide
- Overall Diagram of Equipment Networking: Refer to the diagram for setup.
- Operating Environment Requirements:
- Operating temperature : 0°C to 55°C
- Storage temperature : -20°C to 85°C
- Operating humidity : 5% to 95% (No condensation)
Equipment Management
Connect and Log in to the Device Management
Page: Follow the steps provided to access the management page.
Introduction to Basic Functions
-
System Status
The system interface displays all device status information. -
Network Settings: Internet Settings
Set Internet access policy, connection mode, hostname, MTU, DNS settings, APN, authentication mode, user name, password, PIN code.
Product Manual Overview
This is a CPE of 4G Wireless Data Terminal C AT12 cloud card solution.
Use r Book Graphic Instructions
Graphic Format | Description |
---|---|
< > | The button that represents the page. |
“” | Represents information such as name or password. |
Description of Product Appearance Information
Product Appearance
Port Description
Figure 2-1 description of the port
Name | Instructions |
---|---|
RST | Reset key (hold down for 8 seconds to restore the system to factory |
Settings)
POW| Power button
WPS| WPS keys
SIM| 1 SIM slot/press type
---|---
WAN/LAN| 1 WAN port (switchable LAN port)
LAN| 3 LAN port
DC| 1 Power interface (12V/2A)
External antenna| 4 * CAT12 4G antenna interface
Light Position Description
Name | Status | Description |
---|
POW Light
| Green Light Off| The device not powered on
Green Light On| Device powered on
NET Light
| Green Light Off| No data connection
Green Light On| Data connection
SMS/WPS Light
| Off Green Light| Wireless Off
Green Light On| Wireless On
Green Light flashing slowly
(1s:1s=On:Off)2MIN
| ****
WPS button pressed
4.5G Light
| RSRP (dBm)
<-115| [-115,-110)| [-110,-105)| [-105,-95)| [-95,-85)| >=-85
SINR (dB)
| <-3| 0| 1| 1| 1| 1| 1
[-3,1)| 0| 1| 1| 2| 2| 2
[1, 4, 6)| 0| 1| 2| 3| 3| 3
[7, 9, 13)| 0| 1| 2| 3| 4| 4
=13dB| 0| 1| 2| 3| 4| 5
Button reset| Press the reset button for 5S, and 4.5G lights 1, 2, 3, 4, and 5 will be on simultaneously
Green light flashing fast (0.1s: 0.1s=On: Off)
Equipment Quick Installation Guide
Overall Diagram of Equipment Networking
Operating Environment Requirements
Operating temperature | 0 ℃ ~ 55 ℃ |
---|---|
Storage temperature | – 20 ℃ ~ 85 ℃ |
Operating humidity | 5% to 95% (No condensation) |
Equipment Management
Note:
The following operations are performed without accessing the external network.
If the device is already connected to an external network, remove the external
network cable and follow the steps below .
Connect and Log in to the Device Management Page
- Use a network cable to connect the device’s LAN port and the computer’s network port separately .
- After waiting for more than ten seconds, the computer will automatically obtains the address.
- Open the browser page, enter the gateway address of the device “192.168.1.1” in the address bar of the browser page (the gateway address of the device is marked on the label on the back of the device, the default address is 192.168.1.1) to jump to the p age.
- After successful page jump, the login interface of the device will be displayed, please enter the password “admin” in the page according to the prompt (the password is marked on the label on the back of the device, the initial password is admin by defau lt), and then click < Login > button.
- After successfully logging in to the device management interface, you can view the basic information of the device and man age the operation of the device.
Introduction to Basic Functions
System Status
The system interface can intuitively display all the current status
information of the device, and the unique module popup in terface can clearly
and accurately display more setting information.
- System information: Automatically displays the operating days and the current software version and model;
- LAN information: Displays the address of the LAN port and the number of users;
- Resource usage information: Displays CPU and M emory usage status , and interface information;
- 2.4G/5G wireless information: Display 2.4G/5G wireless status and name, password, channel;
- Modem information: Display APN connection status and signal strength;
- Routing information: Displays rout e status, number of static and policy rout e connections.
Network Settings
-
Internet Settings
Can be used to set Internet access policy, connection mode, host name, MTU, DNS settings, APN, authentication mode, user name , password, PIN code . -
LAN Settings
Can be used to set the LAN port IP address and DHCP address -
USSD
To obtain USSD service information, please check whether the operator supports it when using the service and press the cancel button at the end of the service. -
SMS Service
You can send emails to others and record the contents of sending and receiving -
DDNS Settings
This mode is turned off by default, and when turned on, provides a valid, unchanging Internet domain name (URL address) to match a (likely ever- changing) IP address.
Wireless Settings
-
Basic Settings
In this mode, the basic information of a 2.4G/5G wireless network can be set (for example Wireless N ame, Password, Frequency B and, B and width, Channel, Country/Region). -
Guest Network
This mode is off by default, but when it is on , you can set up the 2.4G/5G wireless network separately. With the guest network function, users can set up an independent Internet environment for guest s, which uses a separate Internet key This not only prevents the leakage of the user’s own Internet key, but also prevents the leakage of user data information, thus further ensuring the security of the home network
Parental Control
This mode is off by default, and when it is on, it help s you to limit your
child’s online time by not being able to access the Internet outside of the
set allowable online time.
Device Management
This function is turned off by default and can be used to set up static DHCP
services when enabled.
Smart QoS
This function is turned off by defaul t, when it is on, you can intelligently
speed limit rules in the list. Supports Quality of Service ( and intelligent
QoS bandwidth management based on services and IP network segments.
Security Settings
-
IP/Port Filtering
This function is turned off by default, when it is on, you can set up IP/Oort filtering, it is used to restrict LAN users from accessing the Internet . -
MAC Filtering
This function is turned off by default, when it is on, it is used to restrict access to the Internet by certain users on the LAN. The MACs in the list will be prohibited from accessing the Internet through the gateway when the function is enabled, and the rules in the list will not take effect when the function is disabled. -
URL Filtering
This function is disabled by default, when it is on, it is used to restrict LAN users from accessing the Internet. Enabling this feature will prohibit the domains in the list from being accessed by users. The rules of the list do not take effect when this feature is disabled.
NAT Forwarding
-
Port Forwarding
This function is turned off by default, but when it is turned on, port forwarding is set up to provide services over the Internet . -
DMZ
This function is turned off by default, but when it is turned on, it protects you from direct exposure to external networks and attacks. -
VPN Penetration
Used to set up VPN penetration service functions.
System Services
-
Remote Management
Used to set up the remote management function of the system, turned off by default. -
SNMP
Used to set up the SNMP service, turned off by default.
System Administration
-
Changing the Administrator Password
- Old password : The default password of the device is “admin”, which is marked on the label on the back of the device. The password can be changed to a maximum of 32 characters (that is, 32 bit English characters, digits, and special characters).
- New password : The password can be changed to a maximum of 32 characters (that is, 32 bit English characters, digits, and special characters).
- Confirm password : Enter the new password once to confirm the success.
-
Time Settings
- Select time zone: 24 time zone options are supported from 12 to +12, and users can set the time according to the local time.
- Automatically synchronize NTP time: After this option is selected, the device automatically synchronizes time based on the NTP server address. If this option is not selected, the device automatically starts time based on the current time. It is generally not recommended to deselect this option.
- NTP server: The IP addresses of the three servers are automatically updated at the same time and it is generally not recommended to change them
-
Scheduled Restart
Used to restart the device. Tap Restart to restart the device. -
Firmware Upgrade
- Firmware version : Automatically displays the current version number. When the device is connected to the network, click the < Detect New Version > button, and the device will automatically detect if there is a new version that can be upgraded. If ther e is a new version, th e page prompts if there is a new version and whether it needs to be upgraded, and a < Upgrade > button appears.
- Do not retain the configuration : This function is used with the firmware upgrade function. If this function is selected, the original configuration of the device will be cleared after the firmware upgrade is successful .
- Select file : Support page to manually upgrade the firmware, the user can choose the different version of firmware with the device to upgrade by themselves
-
System Configuration
- Backup configuration file: Automatically saves the configuration of the current device into a file, which is convenient for later restoration to factory defaults.
- Restore configuration file: Select the saved configuration file or another configuration file to update. After the device is restarted, the device configuration automatically changes to the configuration status of the updated configuration file.
- Reset system configuration: Click the < Restore > button, and the device automatically clears all settings and restores to the original factory state.
-
Ping Diagnostics
Simply enter the address you want to ping and the number of bars you want to ping, and tap apply to perform ping diagnostics. -
Route Tracing: Simply enter the address to be traced and the number of entries to be traced and click “Execute” to route the trace
-
System Logs
This function is turned off by default and displays system logs when enabled . -
Exit
Log out of the device background login.
Specifications
Chip
configuration
| ****
Flash/RAM
| ****
Flash: 16MByter RAM: 128MByte
---|---|---
Machine port
| Keys| 1Reset button, 1WPS button, 1 Power button
Module interface| M.2 (Standard M.2 base; Compatible with USB3.0 and
8111H Phy)
SIM card holder| CAT12: Virtual cloud card + pluggable SIM (add SIM
switch)
Network Port| 1 adaptive 10/100/1000Mbps WAN port (switchable LAN port)
3 adaptive 10/100/1000Mbps LAN ports
Antenna| CAT 12 external antenna 4, WIFI antenna built-in (onboard) 2
Power Supply| 1DC 12V/2A
Light bits| Light position| 1POW, 1NET, 1WIFI, 1WAN, 1LAN,
34.5G SIGNAL
Work environment
| Operating temperature| 0°C ~ 55°C
Operating humidity| 5% to 95% (no condensation)
Storage temperature| -20°C ~ 85°C
Mechanical Properties
| Mounting method| Desktop, stereo, etc.
Size| 186 159.3 49 mm
Shell| Plastic case
FCC regulation
Warning : Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
MPE & SAR
FCC Radiation Exposure Statement
This equipment complied with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FAQ
Q: How do I reset the device to factory settings?
A: Press and hold the reset key for 8 seconds to restore the system to
factory settings.