ZEBEX BRC-RS95 Gun Type Wireless Handheld Scanner User Guide
- July 26, 2024
- ZEBEX
Table of Contents
ZEBEX BRC-RS95 Gun Type Wireless Handheld Scanner User Guide
Scanner Outline
Package Contents
*Note: Content in this section is for reference only. Please consult the actual packaging for contents. Additionally, product appearance may differ.
Installation
-
Battery : Unscrew the cap to install the battery, ensuring the positive end is facing forward. Caution: Incorrect installation may damage the scanner. Additionally, when removing the battery, support it with your thumb, as it may spring out due to the internal spring.
-
Cable Clip : Insert the cable clip into the hand strap hole, turn to secure, and press firmly until locked. Finally, use the clasp to secure the cable as shown.
-
Cradle : Connect USB‐C cable and communication cable to the cradle as illustrated
Pairing the Device
Cradle Host Mode
-
Connect the cradle and the computer using the cables. Please make sure the cradle LED is flashing blue indicating it’s not linked to any scanner.
-
Power on the scanner and scan the following barcodes: Start Of Configuration, Cradle Host mode enable, and End Of Configuration to enable Cradle Host mode.
-
Scan the pairing barcode attached at the bottom of the cradle to begin pairing. 3 short beeps will be heard.
-
The LED indicator on the scanner will flash blue rapidly indicating search mode in progress. LED on the cradle will become steady blue when the pairing is successful.
-
To set the host interface for the cradle, scan the corresponding barcode label found in the System Settings in the User’s Manual.
BT HID/Smart Phone Mode
-
Power on the scanner and program it with “BT HID Mode.”
To connect to a smart phone (ie. iPhone, Android), the Smart phone mode must also be enabled. -
Enable wireless discovery on your smart phone. (see your phone’s user’s manual for instructions)
-
The scanner should be on the list of discoverable devices. The default name of the scanner is “ZBBT”. Select “ZBBT” from the list and a pin code will appear on your smart phone.
-
To input the pin code, use the scanner to scan the barcodes in the ASCII table found in the previous section. For example: if the pin code is “0111”, scan “0”, “1”, “1”, “1” from the ASCII barcode labels.
-
Scan the Enter barcode in the ASCII table to confirm.
-
A short beep should be heard upon connection.
SPP Client Mode (PC as Host)
In this mode, the scanner is discoverable from a remote device and it can request the scanner for connection. There are several ways to connect the wireless scanner to your PC. Please check the corresponding guides for more details on how to configure your host device’s wireless connections.
-
Turn on the host computer and activate its wireless connection.
-
Power on the scanner and program it with “SPP Client mode” label.
-
In the host computer, execute the discovering procedure and find the scanner.
-
Scanner should be on the list of discoverable devices. The default name of the scanner is “ZBBT”. Select “ZBBT” and click “Next”.
-
Select “Let me choose my own passkey” and enter the pin code. The default pin code is “12345678” (must be at least 4 digits and not more than 8 numeric digits).
-
Click “Next” to connect the scanner to the host. A short beep should be heard upon connection.
SPP Host Mode (Scanner as Host)
In this mode, the scanner initiates the connection to the remote device.
-
Power on of the remote device and have its address ready in hand and make it discoverable.
-
Program the scanner with the “SPP Host enable” barcode.
-
Scan “Set wireless address” to set the address.
-
Use the ASCII table provided in the preceding section to input the 12‐digit wireless address. For instance, if the address reads “011B1345600,” proceed by scanning the corresponding ASCII barcode labels: “0,” “0,” “1,” “1,” “B,” “1,” “3,” “4,” “5,” “6,” “0,” “0.” Alternatively, if an address label is accessible, simply scan it instead.
-
Scan “Confirm Setting” to store the address.
-
Scan ”End” to finish the setup.
-
If necessary, set up and input the pin code (For details, please see User’s Manual). Finally. scan “Required Pair with client (SPP Host)” to begin pairing.
Radio Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
This device and its antenna must not be co‐located or operating in conjunction
with any other antenna or transmitter.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. (for scanner)
Radio Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
This device and its antenna must not be co‐located or operating in conjunction
with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. (for cradle)
ASCII Table
Documents / Resources
|
ZEBEX BRC-RS95 Gun Type Wireless Handheld
Scanner
[pdf] User Guide
BRC-RS95, BRC-RS95 Gun Type Wireless Handheld Scanner, Gun Type Wireless
Handheld Scanner, Wireless Handheld Scanner, Handheld Scanner, Scanner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>