miLEDo CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light Instruction Manual

June 3, 2024
miLEDo

miLEDo - logo CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light
Instruction Manual CORSO LED V2 12-NW-SE
CORSO LED V2 18-NW-SE
CORSO LED V2 24-NW-SE
Aprisa s.r.o., Sadová 618, 738 01 Frýdek-Místek, Czech Republic

CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light

miLEDo CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light - Figure
1miLEDo CORSO LED V2 12-NW-SE
Ceiling-Mounted LED Light - Figure 2miLEDo CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light -
Figure 3miLEDo CORSO LED V2
12-NW-SE Ceiling-Mounted LED Light - Figure 4miLEDo CORSO LED V2 12-NW-SE Ceiling-Mounted LED Light -
Figure 5miLEDo CORSO LED V2
12-NW-SE Ceiling-Mounted LED Light - Figure 6

INTENDED USE/APPLICATION

Product designed for the use in households and for other similar general applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should be performed by an appropriately qualified person. Any activities to be done with  disconnected power supply. Exercise particular caution. Product has a protective contact/terminal. Failure to connect the protective lead may lead to electric shock. Mounting  diagram: see pictures. Check for proper mechanical fastening and connection to electrical power prior to first use. The product can be connected to a supply  network which meets energy quality standards as prescribed by law. To maintain the proper IP protection level, the right diameter of the power cable should be selected for  the cable gland used in the product.

FUNCTIONAL CHARACTERISTICS

Product can be used either indoors or outdoors.
USAGE GUIDELINES/MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and the product has cooled down. Clean only with soft and dry cloths. Do not use chemical  detergents. Do not cover the product. Ensure free air access. Product may heat up to a higher temperature. ATTENTION! Do not look directly at LED light beam. Product  can only be supplied by rated voltage or voltage within the range provided. It’s forbidden to use the product with damaged protective cover. Product must not be used in  unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air atmosphere, fumes, or chemical fumes, etc.
EXPLANATIONS OF SYMBOLS USED
P2: KrP3: NP4: NP5: NP6: KP7: FP8: CP9: KaanP10: SP11: P12: BP13: KP14: PP15: beschermglas P1: Rated voltage, frequency.
P2: Rated power.
P3: Rated luminous flux. The specified luminous flux refers to the light source (LED module) used.
P4: Rated luminous flux.
P5: Rated durability.
P6: Colour temperature.
P7: Colour Rendering Index.
P8: Certificate of Conformity confirming the quality of production in accordance with approved standards on the territory of the Customs Union.
P9: Class I. A product in which protection against electric shock is provided not only by means of basic insulation but also through additional safety measures, i.e. extra  protective circuit to which protective conductor of the fixed feeding installation needs to be connected.
P10: The symbol describes the minimal distance of a light fixture (its light source) from the spots and objects that it’s illuminating.
P11: Viewing angle.
P12: Protection against solid foreign objects bigger than 1,0mm provided. Protection against splashing water provided.
P13: Product can be used either indoors or outdoors.
P14: The product is not compatible with lighting dimmers.
P15: The product can only be used in a lighting fixture with protective glass. The chipped globe, screen or protective shield must be replaced immediately.
P16: Product meets the requirements of EU directives.
P17: The product is compliant with all relevant United Kingdom regulations.
P18: This product is equipped with a light source with energy efficiency class F
P19: The LED light source can only be replaced by qualified personnel (Aprisa service only).
P20: Any control panel or control equipment can only be replaced by qualified personnel (Aprisa service only).
P21: Environmental operating temperature range that the product can be exposed to.
P22: Micro-gap between transmitter contacts.

ENVIRONMENTAL PROTECTION

Keep your environment clean. Segregation of post-packaging waste is recommended.
P23: This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same  way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/neutralising.
Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local  authorities or sellers of such goods. Used items can also be returned to the seller when new product is purchased, in quantity no larger than the purchased item of the same  type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in  a given area is recommended.

COMMENTS/GUIDELINES

Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. Aprisa s.r.o. reserves the right to  make changes in the manual – the current version can be downloaded at www.kanlux.com. For more information about Miledo products visit www.kanlux.com. Aprisa s.r.o.  shall not be responsible for any damage resulting from the failure to follow these instructions. CE
declaration of compliance: We, Aprisa s.r.o., hereby declare the product is compliant with the basic requirements and other respective provisions of Directive 2014/53/EU.  The declaration of compliance is available in electronic form on the company’s website: www.kanlux.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals