nocco DCG 09 017 Brecknell POS Scale User Guide
- July 24, 2024
- nocco
Table of Contents
nocco DCG 09 017 Brecknell POS Scale
Specifications
- Model: Brecknell 6710 Series
- Parts Included: Display pad, scale body, power adapter, USB cable, DateCodeGenie device
- Tools Required: Phillips screwdriver, 8mm wrench
Product Usage Instructions
Scale Setup
- Feed display pad cable through front square cutout in display bracket.
- Flip display pad upside down to locate both hinge pins. Insert hinge pins into hinge holes of display bracket and snap in place.
- Remove cover from scale body and set aside.
- Turn scale body upside down. Remove and discard five short mounting screws with Phillips screwdriver and shipping screw with 8mm wrench provided.
- Align four holes of the display unit with the four mounting holes on the scale body. Insert longer mounting screws and tighten with Phillips screwdriver to attach.
- Feed display pad cable through round opening in scale body.
- Turn the scale body upright and connect display pad cable to matching port inside scale body.
- Wrap excess cable around display bracket hooks.
- Turn the scale body upright. Connect Power adapter and USB cable to matching ports on scale body and to outlet and USB port on DateCodeGenie device.
- Place the scale in final location for use and view the level bubble. Adjust the feet until the bubble is centered.
- Remove blue film from scale cover. Then place cover onto scale body. Adjust display to best viewing angle.
- Press the display pad to power on scale and press again (less than 3 seconds) to zero the scale. Press (less than 3 seconds) to change unit of measure. Press and hold (more than 3 seconds) to turn scale off.
Certification
Scale must be certified by your local weights and measures inspector.
LCD Display Pad Functions
Refer to the key functions listed in the manual for various operations such as entering setup mode, changing units, tare function, input data mode, menu selection, power on/off, etc.
Parts Included
- Scale body
- Display pad with cable
- Display bracket
- 4 Mounting screws
- USB cable
- Power adapter (12V)
Tools Required
- Phillips screwdriver
- 8mm wrench (included)
Scale Setup
-
Feed display pad cable through front square cutout in display bracket.
-
Flip display pad upside down to locate both hinge pins. Insert hinge pins into hinge holes of display bracket and snap in place.
-
Remove cover from scale body and set aside.
-
Turn scale body upside down. Remove and discard, five short mounting screws with Phillips screwdriver and shipping screw with 8mm wrench provided.
-
Align four holes of the display unit with the four mounting holes on the scale body. Insert longer mounting screws and tighten with Phillips screwdriver to attach.
-
Feed display pad cable through round opening in scale body.
-
Turn the scale body upright and connect display pad cable to matching port inside scale body.
-
Wrap excess cable around display bracket hooks.
-
Turn the scale body upright. Connect Power adapter and USB cable to matching ports on scale body and to outlet and USB port on DateCodeGenie device.
-
Place the scale in final location for use and view the level bubble. Adjust the feet until the bubble is centered.
-
Remove blue film from scale cover. Then place cover onto scale body. Adjust display to best viewing angle.
-
Press the display pad to power on scale and press again (less than 3 seconds) to zero the scale. Press (less than 3 seconds) to change unit of measure. Press and hold (more than 3 seconds) to turn scale off.
Scale must be certified by your local weights and measures inspector
LCD Display Pad
Training Resources
Have a DateCodeGenie question? Find the answer in our knowledge base.
datecodegenie.com/support
Log into your portal at datecodegenie.com and access all training tools from the Support tab. See videos, knowledge base and more.
Contact & Support
Americas & Asia
Technical Support
800.774.0478 x 1 dcgsupport@ncco.com
Europe & UAE
Technical Support
00 44 (0)1283 527299 x 4 supportdcg@ncco.com
Order Processing
800.328.6508
cs@ncco.com
Customer Service
00 44 (0)1283 527977 option 4
supportdcg@ncco.com
To learn more about NCCO and view a full list of our products, visit us at ncco.com.
Looking for warranty information on your product? Limited- warranty information for DateCodeGenie products and third- party warranty information for accessories are all available to view and download at: support.datecodegenie.com/warranty This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FAQ
How do I calibrate the input voltage value?
To calibrate the input voltage value, press the designated button for more than 3 seconds as indicated in the manual.
How do I set or clear tare code?
In the Display ADC code mode, follow the instructions in the manual to set or clear the tare code.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>