Moory TH Series Tubular Heater Instruction Manual
- July 20, 2024
- Moory
Table of Contents
Moory TH Series Tubular Heater Instruction Manual
YOU SHOULD READ THE MANUAL CAREFULLY BEFORE USING
DISPOSAL
This symbol indicates that this product must not be placed in general household waste. It should beset to separate recycling facility for recovery, check Local Authorities for details.
By responsible recycling and separating this product from other household waste it will help protect the environment and human health, as the volume of waste sent to incinerators
Read all the instructions prior to use.
This item gets very hot: do not touch the tubular heater when it is switched on. Do not cover the tubular heater as this will cause overheating. Never place the tubular heater directly on the floor without using the feet
WARNING: Check product before use: if cord is damaged, it must be replaced by the manufacturer if still under warranty, or a similar qualified person to avoid any hazards
Safety Regulations
-
During the first use the heater may emit a small amount ofvapourwhich is perfectly normal. The reason for this istheheatingwireelement is coated with some lubricant oil duringtheproductionprocess. This will stop after approx. 5 minutes after thefirstuseand is not a safety concern.
The tubular heater is not suitable for use outdoors. -
Do not submerge into water.
-
Place in a safe place away from flammable objects.
-
Do not place flammable liquids or gasses near the heater.
-
Do not place the heater directly below the socket outlet.
-
Do not let the power cord over hang or touch the tube.
-
Keep out of reach of children and animals – product gets hot to touch.
-
This is not a toy.
-
Switch off appliance when not in use.
-
Do not hold the tubular heater by the cord.
-
If using an extension cord it must be as short as possible and fully extended.
-
Check heater regularly if using with a timer or any other device that switches the tubular heater onoroffautomatically.
-
This leaflet should be retained for instructions on use.
-
Always connect to a RCD protected circuit / that covered by a safety switch.
-
The is a greenhouse heater and not intended for use inside the home.
Cleaning
Ensure product is unplugged from the mains. Ensure product is completely cold.
Wipe with a damp cloth, then finish by drying with a soft cloth. DO NOT use abrasive cleaning powders, clothe or metal polishes on any part of the tubular heater as this will cause damage.
Thermal Cut-out
The appliance is fitted with a thermal cut-out. Once the tubular heater has cooled down it will re-set itself automatically. It will then switch on and off until the reason for overheating has been removed.
Mounting instructions
Please install horizontally, prohibited vertically.
Notice: DO NOT SWITCH POWER ON TO THE HEATER UNTIL IT IS SECURELY MOUNTED
.
Step 1. Install the bracket as the picture showed .
Step 2. Fix the tubular heater on the wall or on the floor as below .
Tubular Heater Notice
- When the room has reached the desired temperature, turn the thermostat knob in an anti-clockwise direction just until a small sound is heard and not beyond.
- The temperature will then be regulated and kept at a constant level by the thermostat.
- The heater is fitted with a safety device which will switch off the heater in case of accidental overheating .
- Make sure that any causes of overheating, such as obstructions, are removed and plug theapplianceinagain.
Tubular heater Specifications
Model No.| Power| Electrical Supply| IP Rating| Product Length (mm)| Product
Size (mm)
---|---|---|---|---|---
TH01B| 60W| 220-240V ,50 Hz| IP44| 300mm| 3859590
TH02B| 120W| 220-240V ,50 Hz| IP44| 609mm| 6859590
TH03B| 180W| 220-240V ,50 Hz| IP44| 900mm| 9959590
TH04B| 240W| 220-240V ,50 Hz| IP44| 1200mm| 12959590
Warranty
This product is guaranteed under warranty and covers defects in material or workmanship from1 year of date of purchase. The original bill of purchase (with purchase date) must be submitted. The warranty will not apply in cases of: Misuse: by non-compliance of the instructions, normal wear and tear, incorrectuse,e.g. overloading, non approved accessories, force or damaged caused by external forces, if the plug has beentamperedwith or removed, partially or completely dismantled product, or interference by non-qualified persons.
