Luoware LW-S01 LITE Smart Toilet Instruction Manual
- July 20, 2024
- Luoware
Table of Contents
Luoware LW-S01 LITE Smart Toilet
Luoware SMART TOILET
Concealed cistern series
INSTRUCTION MANUAL
Model: LW-507 LITE
Customer Service Email: support@luoware.xyz
-
Thank you for purchasing our product.
Before using, please read the instruction carefully. Please keep the instruction properly for further reference. -
Our company reserves the right of final interpretation for this manual. The manual is subject to change without notice.
Packing List
Dear user ,
Please count the following items after opening the package:
Dear user,
Please count the following items after opening the package:
Battery Box for Power Outage Flush
Installation of the Battery Box for Power Outage
-
This battery box is for use as backup during power outages. The battery box must not be used simultaneously with a plugged-in power source when the toilet is in operation. It is recommended to connect it to the main unit only during power outages. We accept no responsibility for the consequences of using dual power sources at the same time, and such usage is not covered by the warranty.
-
Before activating the power outage flushing function, install 10 AA alkaline batteries (Batteries not supplied. Please purchase batteries separately before installation.) into the battery box in advance (open the battery box with a screwdriver). Do not mix new and old batteries, batteries of different models, or batteries from different brands.
When replacing the batteries, ensure that all are replaced at the same time. -
Please follow the “+” and “-” signs on the battery box when installing batteries. This battery box is a series battery group, and no single cell can be reversed. Failing to do so may cause battery damage, and in severe cases, may pose safety hazards such as explosion and combustion.
-
Take out the battery connection cable from the rear side of seat cover and connect it to the battery box, ensuring that it is plugged in place.
-
Do not disassemble the battery box unnecessarily. After replacing the battery, make sure to seal the battery box tightly. If moisture from the bathroom gets into the box, it could cause the batteries to rust and become damaged.
-
When replacing batteries, disconnect the battery box from the main unit.
-
To avoid potential hazards, this battery box cannot be recharged.
Components
Technical Drawing
Features
Seat Sensor
All corresponding functions will be activated and be ready after seated.
Seat Ring Temperature Adjustment
Heated seat with 4 levels of temperature adjustment: normal (room
temperature)/ high / medium / low.
Off Seat Auto Flush
Auto flush after using and standing up from the toilet seat.
Foot Sensor to Flush
Flush by lifting the foot near the sensor.
Flush by Side Knob
Flush by pressing the side knob on the smart toilet.
Night Light
The night light is designed to be gentle on the eyes and provide enough
illumination to navigate the bathroom without needing to turn on any harsh
overhead lights.
Power Outage Flush
Equipped with a backup battery box, the backup battery can be activated for
flushing when there is a power outage.
Attention
WARNING
Do not pull the plug with wet hand.
Otherwise, it may cause electric shock.
Do not pour water, detergent or deodorant on the smart toilet main unit and power plug. Otherwise:
- lt may cause fire, electric shock, short circuit or damage .
- lnjury or indoor water seepage may occur due to product damage.
When there is thunder, do not touch the power plug.
Otherwise, it may cause electric shock.
Do not touch the water inlet hose to the power plug or outlet.
Otherwise, it may cause fire, electric shock, heating, or short circuit due to
condensation.
Do not damage the power cord or plug. Do not forcefully drop, pull, twist, bend, scratch, process, heat, place heavy objects on, tie, or clamp the power cord or plug.
Otherwise, it may cause product damage. Continuing to use the product in a damaged state may cause fire, electric shock, heating, or short circuit.
Do not use water sources other than tap water or potable well water (groundwater). Otherwise:
- Alt may cause corrosion in components or machine malfunctions.
- Alt may cause skin inflammation or burns due to unclean water.
Beware of low-temperature burns.
- A Improper use of the warm seat ring may result in low-temperature burns.
- Alf sitting on the seat ring for a long time, please set the temperature of the seat ring to normal/unheated (room temperature).
- When using the warm seat ring or warm air drying function, please set the temperature of the seat ring to normal/unheated (room temperature) and the temperature of the warm air dryer to the lowest setting for the following groups of people.
- Children, the elderly, and those who are unable to adjust the temperature to a suitable level themselves.
- Individuals with behavioral impairments such as patients or people with disabilities.
- Individuals who have taken hypnotic drugs (such as sleeping pills, cold medicine, etc.), heavy drinkers, and those who are excessively fatigued must use this product under the supervision of a responsible person.
Please confirm that the power outlet has been waterproofed.
Make sure of the position of the outlet before installation and keep it away
from the bathtub as much as possible.
Alf it is not waterproofed, it may cause fire or electric shock.
For the installation and waterproofing of the outlet, please consult qualified
professionals.
Please confirm that the outlet being used is correctly grounded.
- Otherwise, it may cause electric shock due to malfunction or short circuit.
- When installing the ground wire, please entrust a professional installation company.
MANDATORY!
Do not pull out the power plug by holding the power cord. When unplugging the
power plug, do not hold the power cord, but hold the power plug.
Otherwise, it may cause fire or heating due to damage to the power cord.
Please make sure to firmly insert the power plug into the outlet.
MANDATORY!
Otherwise, it may cause fire, heating, or short circuit.
If the power cord is damaged, it must be replaced by the manufacturer,
maintenance department, or other professionals to avoid potential hazards.
When performing maintenance, be sure to turn off the power.
MANDATORY!
Otherwise, it may cause electric shock.
MANDATORY!
This is an electrical product. Do not install it in places where it is easy to
be splashed with water or where the humidity is high. When using it in the
bathroom, please install an exhaust fan or ventilation opening to keep the
bathroom well ventilated.
****Otherwise, it may cause fire or electric shock.
When removing the smart toilet main unit, be sure to disconnect the power.
****Otherwise, it may cause fire or electric shock.
Individuals with physical, sensory, or cognitive disabilities, or those
lacking experience and knowledge of this product (including children), must
use this product under the supervision of a responsible person. Children
should not play with this product.
****Otherwise, it may cause burn, electric shock, fire, or injury.
NO BURNING
Do not let cigarettes or other sources of fire get dose to the product.
- Otherwise, it may cause fire.
When maintaining plastic parts (seat ring, seat cover, etc.) and water inlet hoses, please use kitchen detergent (neutral). Do not use the following items: toilet cleaner, household detergent, gasoline, benzene, washing powder, or nylon brushes. Otherwise:
- It may damage plastic parts, causing cracks and resulting in personal injury or malfunction.
- It may damage the water inlet hose and cause water leakage.
Do not forcibly impact the product. Do not place heavy objects on or stand on the seat ring, seat cover, or smart toilet main unit. Otherwise:
- The product may crack, and the smart toilet main unit may detach and fall, causing personal injury.
- Injury or indoor water seepage may occur due to product damage.
- Do not use the smart toilet when its main unit is loose.
- Otherwise, the smart toilet main unit may detach and faU, causing personal injury.
Do not use your hands to lift the smart toilet main unit by holding the seat
ring or seat cover. Do not open the seat ring or seat cover when there are
items on them.
Otherwise, the smart toilet main unit may detach and fall, causing personal
injury.
Do not violently open or close the seat cover or seat ring, or swing the seat
cover and seat ring quickly. Otherwise:
- The flipping device may fail due to the powerful external force.
- The main unit may break or detach from the toilet body due to powerful external force, causing personal injury.
Do not bend or damage the water inlet hose.
- Otherwise, it may cause water leakage.
Installation Instruction
Installation of the Smart Toilet
-
Confirmation of installation environment
Before installation, please confirm that the bathroom wall and floor tiles have been completed, and that the sewage pipes, water pipes, and electrical circuits have been reserved as shown in the figure below. This toilet rough-in is 300mm (11.81 in); Water inlet pressure range: 0.1 SMpa (dynamic) – 0.75Mpa (static); water inlet temperature: °4 C-35°C (39.2°F-95°F). -
Assembly of dedicated shut-off valve
Install the shut-off valve provided with the product.
Note : Remove the old water supply valve if it has been installed before. -
Installation and mounting of the toilet
-
Assemble the mounting bracket with bolts and then secure them to the flange on the ground and tighten with nuts. Please refer to Figure 1.0 on the next page for details.
-
Insert the wax ring gasket under the toilet.
-
Install the toilet on the corresponding position.
Flange accessories package
Details :
-
Nut 5/16 (2pcs)
-
L-shaped plastic fixed block {2pcs)
-
Large washer-8x24xl.8mm (2pcs)
-
Flange-ABS (1 pc)
-
Bolt-8x43mm {2pcs)
-
Small expansion plastic sleeve (4pcs)
-
Sealing wax ring -thick (1 pc)
-
Round head self tapping screw-5x36mm (4pcs)
-
T-shaped pad (2pcs)
-
Flat head tapping screw-5x75mm (2pcs)
-
Decorative cap (2pcs)
-
Sealing wax ring – thin (1 pc)
Optional accessories -
Outer hexagon self tapping screw-6x60mm (2pcs)
-
Small washer-6xl 6xl mm (2pcs)
-
Large expansion plastic sleeve (2 pcs)
Optional accessories
- Put the screw through the T-shaped pad and then install it through the holes (on both sides of the toilet ceramic) to the mounting bracket (L-shaped plastic fixed block) on the ground, and tighten it securely with a tool.
- Put the decorative cap on the T-shaped pad.
- Connect the water inlet hose and water pump with the water tank and tighten them with an adjustable wrench.
Caulk the bottom of the toilet with silicone sealant. Connection of the
water inlet hose
Connect the inlet hose with the shut-off valve by using tools like wrench.
(Valve Installation – Refer to Page 3 for Details)
Notice: After installation, turn on the shut-off valve to check whether it leaks.
Preparation before Use
-
Open the shut-off valve
Turn the valve counterclockwise to fully open the water supply valve. -
Plug the power plug into the outlet.
Plug the power plug into a 120V power outlet. The smart toilet will perform a self-check run once, and the main unit will be in standby mode.
- Do not use wiring that exceeds the power supply specifications, such as an extension cord.
- The outlet must be reliably and safely grounded.
How to Use
Side Knob
- Rotate clockwise to increase seat temperature.
- Rotate counterclockwise to decrease seat temperature.
- Press the side knob to flush.
- Long press the side knob for 3 seconds to turn the night light on/off.
Functions
-
Flush
Auto Flush: The toilet will auto flush once when the user stands up from the seat. Flush by the Side Knob: Short press the knob down vertically to flush once.
Flush by Foot Sensor: Stretch your foot slightly against the sensor sign on the ceramic surface, and the water will start flowing once you remove your foot. -
Heated Seat
The seat ring temperature can be adjusted to 4 different levels, including room temperature, high, medium, and low levels. Rotate the side knob to switch between different temperature levels.
Cleaning and Maintenance
-
Clean and Maintain the Power Plug
Please clean the power plug regularly. When cleaning, remove the power plug from the outlet and wipe it with a dry cloth. -
Dust accumulation on the power plug may cause fire.
Clean and Maintain the Main Unit of the Smart Toilet
When cleaning the surface of the main unit, please wipe it with a soft, wet
cloth.
- When cleaning and maintaining the smart toilet main unit, please pull the power plug out of the outlet to avoid any contact with water.
- If the surface has stubborn stains, you can use a soft, wet cloth with neutral kitchen detergent to clean it.
Clean and Maintain the Ceramic Part of the Smart Toilet
You can pour a neutral toilet cleaner onto a soft brush or sponge and use it
to clean the ceramic pa rt of the smart toilet. Rinse the area with tap water
after cleaning.
- Do not use detergents or disinfectants that contain chlorine or are acidic.
- Do not use brushes that contain abrasive materials.
When not in use for a long time
When not using this product for a long time, please be sure to drain all the
water from the smart toilet to prevent water deterioration and freezing. Also,
turn off the power and remove the battery from the remote control.
- Close the shut-off va Ive and stop the water supply.
- Unplug the power plug from the outlet.
- Remove the water hose from the shut-off valve, drain the water from the hose, and then reinstall it.
When using again, open the shut-off valve, plug the power plug back into the outlet.
Troubleshooting
Some malfunctions can be resolved by simple operations. Please confirm the following items before authorizing a professional to repair the product.
Product Specification
Warranty
Luoware warrants its products as listed in below to be free of material and
workmanship defect, subjected to the limitations set forth in this limited
warranty.
Model Numbe r: LW-S0l LITE, 2 years limited to be free of defects in
material and workmanship.
This limited warranty is non-transferable and only applies to products
purchased and installed in the United States.
This limited warranty excludes all industrial, commercial and business usage.
Proof of purchase (original sales receipt) from the original purchaser,
Description and pictures of defect, model number or model description must be
provided to Luoware for all warranty claims and Luoware IS NOT responsible for
labor cost, removal or installation costs.
This limited warranty shall not apply to goods which have been subject to
accident, negligence, improper installation, product abuse, product misuse, or
use of cleaners containing abrasives, alcohol or other organic solvents,
whether performed by a contractor, service company, or yourself, are excluded
from this warranty.
This warranty does not cover surface damaged caused by use of chemicals that
break through or dissolve the surface finish or damage caused by the
accidental dropping of sharp or heavy objects. Improper care and use of
abrasive cleaners and will void the warranty.
During this limited warranty period if a malfunction occurs and after
inspection it is determined that a defect developed during normal use,
Luoware’s obligations under this warranty are limited to repair, replacement,
or any other appropriate adjustment, at Luowa re’s option, of the smart toilet
or parts found to be defective in normal use, provided that such products are
properly installed, used and serviced in accord a nee with instructions.
Luoware reserves the right to make such inspections as may be necessary in
order to determine the cause of the defect.
Caution:
NEVER use cleaners containing abrasive cleaners, ammonia, bleach, acids,
waxes, alcohol, solvents or other products that are not recommend for Chrome
finish will void the warranty.
Luoware products should be installed by a fully insured and licensed contractor only. Installation by anyone other than fully insured and licensed contractor will void this limited warranty.
RESPONSIBILITIES OF OTHERS
Inspecting the unit prior to installation is the responsibility of the
installer or building contractor who acts on behalf of the user. They are
responsible for ensuring the unit is free of defects or damage. In the event
of a problem, the unit must not be installed. Luoware is not responsible for
failures or damage that could have been discovered, repaired, or avoided by
proper inspection and testing prior to installation.
Damage occurring in transit is the responsibility of the carrier. The user or
installer MUST open the carton and inspect the unit for damage when it is
delivered. If damage is discovered, it must be reported immediately to the
seller and the carrier in writing, and an inspection requested. Failure of the
carrier to respond should be reported to the seller and the carrier. Your
freight claims should be filed promptly thereafter.
This limited warranty does not cover any liability for consequential or
incidental damages, all of which are hereby expressly disclaimed, or the
extension beyond the duration of this limited warranty of any implied limited
warranties, including those of merchantability or fitness for an intended
purpose.
DISCLAIMER
Except as expressly provided, there shall be no warranty or obligation,
express or implied, oral or statutory. No dealer or other person has the
authority to make any warranties or representations concerning or its
products. In no event shall be held responsible for any such warranties or
representations.
Some states/provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion on limitation of special, incidental or consequential
damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, you may also have other rights which
vary from state/province to state/province.
To obtain warranty and replacement parts, please send e-mail to
support@luoware.xyz with the original receipt
information, Luoware will determine how to fix the problem.
www.luoware.xyz
info@luoware.xyz
support@luoware.xyz
@luoware.global
@luoware.global
@luoware
Ver.1.0
Luoware International Industries Inc Add:1888 Calle Madrid, Rowland Heights,
CA 91748
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>