maytronics 8152200 Dolphin Wave Robotic Pool Cleaner Instruction Manual

maytronics 8152200 Dolphin Wave Robotic Pool Cleaner

Dolphin WAVE 100 Pool Cleaner
Operating Instructions
Model Number: 8152200

INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner. The Dolphin WAVE 100 Pool Cleaner offers reliable, convenient, and cost-effective pool cleaning. It features reliable filtration in all pool conditions and an all- surface climbing brush for maximum pool hygiene. The Dolphin WAVE 100 delivers advanced cleaning technology, long-lasting performance, and easy maintenance.

SPECIFICATIONS

• Motor protection: IP 68
• Minimum depth: 0.4 m (1.33 ft)
• Maximum depth: 5 m (16.4 ft)

 WARNINGS AND CAUTIONS

Warnings

• CAUTION: This product should not be used by individuals with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
• Use the originally supplied power supply only
• Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI)
• Keep the power supply out of standing water
• Position the power supply at least 3.5 m (12 ft) away from the edge of the pool
• Do not enter the pool while the pool cleaner is working
• Unplug the power supply before servicing
• Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

Cautions

When not in use, store the Pool Cleaner on the Caddy in a shaded area. Use the Pool Cleaner only in water conditions with appropriate levels of chlorine, pH, temperature, and NaCl.

POOL CLEANER PARTS

The Dolphin WAVE 100 Pool Cleaner includes the following parts:

• Combined Brush: All-surface climbing brush ideal for most pool surfaces
• Wonder Brush: For smooth ceramics (optional)
• Bottom lid and filter bag
• Caddy
• Remote Control Unit
• Filter bag options: Fine – factory default, Ultra fine – extra, Disposable filter bag x 5
• Power Supply Unit

 USING THE POOL CLEANER

 Set Up

Before using the Pool Cleaner for the first time, perform the following steps:

1. Unwind the cable and stretch it out completely so that it has no kinks.

2. Remove the plastic coverings before use.

3. Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up with the groove in the socket on the power supply and turning clockwise (2). Change diagonal handle position for water line sideway movement. To adjust the handle angle:
   A. Press the latch down and hold it in position.
   B. Move the handle to the desired position and release the latch to hold the handle in place. 1,2: Normal advance
   More efficient cleaning action on water-line.
   3,4: Fast advance
   Fast speed – for faster but less efficient cleaning action on water-line.

Putting the Pool Cleaner into the pool
If the foam climbing rings on the brushes are dry, soak them in water until soft. Shake the robot from side to side or turn it upside down to release trapped air. Let it sink to the pool floor.
Turn the power supply ON.

Removing the Pool Cleaner from the pool
The robot will perform automatic shut-off at the end of the cleaning cycle.

• Turn OFF and unplug the power supply.

Using the floating cable, bring the Pool Cleaner to the pool’s edge. DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.

• DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.

Maintenance
Clean the filter bag with a hose. Periodically clean the brushes with a hose. It is recommended to periodically wash the filter bag in a washing machine. Use gentle cycle program.

Cleaning the impeller

• Unplug the power supply.

If you notice debris trapped in the impeller, open the impeller and remove the debris.

Cable
To remove the kinks, stretch the cable out completely and let  it sit for at least a day in the sun.

Off-season storage
If the pool cleaner will not be in use for an extended period, perform the following storage steps:

• Make sure that no water is left in the pool cleaner
• Thoroughly clean the filter bag and insert in place
• Roll up the cable so that it has no kinks and place on the Caddy
• Store the pool cleaner upright on the Caddy in a protected area out of direct sun/rain/frost at a temperature of between 5 °C – 45 °C (41 °F – 113 °F)

POWER SUPPLY

Digital “Switch-Mode” Power Supply with full filter bag and delay indicator.

• Input – 100 VAC – 250 VAC
• 50 Hz – 60 Hz
• 180 W
• Output – <30 VDC
• IP 54

Full filter bag indicator and Reset button
The power supply is equipped with a filter bag status indicator. The red LED indicates two filter conditions.

• When blinking – The filter is partially blocked.
• When lighted – The filter is blocked and must be emptied and cleaned.

If the LED does not turn off after the filter bag had been emptied and cleaned, press the RESET button while the robot is working.

Delay indicator
The power supply is equipped with a Delay indicator that indicates if the Delay option is activated (through the remote control unit).

REMOTE CONTROL UNIT

The remote control unit (RCU) offers two operation modes – Automatic mode and manual direction control mode. In automatic mode, the cleaning parameters can be changed. In manual direction mode, the robot’s motion can be controlled manually.

The Control Panel

Press the Manual/Automatic select button and then choose the desired parameters according to the following table:

Note:

• After 2 minute if no button is pressed, the Remote Control Unit will shut-down and the Pool cleaner will continue to work in the previous settings.
• When the “Ultra-Clean” and “Walls Only” options finish their cycles, the Pool Cleaner will return to default settings.

Caddy assembly

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>