SHABEBE Super Wet Look Stone Sealer User Guide

SHABEBE Super Wet Look Stone Sealer

Product Information

Specifications:

• Product Name: SHABEBE SUPER WET LOOK STONE SEALER
• Application Guide: Included
• Suitable Surfaces: Stone surfaces (not suitable for polished stone or tile)
• Drying Time: 30-60 minutes to touch, full dryness within 48-72 hours (Ideal humidity below 55%)

Frequently Asked Questions

Q: Can this sealer be used on polished stone or tile surfaces?

A: No, this sealer is not suitable for polished stone or tile surfaces. It is specifically designed for use on stone surfaces.

Q: What should I do if I encounter any problems during application?

A: If you encounter any issues or have questions about the product application, please feel free to reach out to us for assistance. We are here to help resolve any problems you may face.

Friendly reminder

1. Following both precautions and operational tips can significantly reduce the likelihood of failures.
2. Please always test a small area to determine suitability of product for intended use and effect.
3. Please note that it is not suitable for polished stoneor tile.
   If there are any problems, please feel free to reach out to us and we will solve them for you!

STEP 1.CLEAN THE SURFACE BY PRESSURE WASHING OR RINSING

PLEASE NOTE THAT THIS STEP IS CRUCIAL AS IT SIGNIFICANTLY IMPACTS THE PRESENTATION OF THE PRODUCT AFTER DRYING）:
Make sure the MUST be dry, clean, and free from grease, oil, wax, dirt, and other sealers. Keep the surface clean, dry and structurally sound. (NOTE: IT IS NOT SUITABLE FOR POLISHED STONEOR TILE)

1. Tips 1: please ensure a thorough application by clearing gaps in the surface to a depth of at least 1-2 inches.
2. Tips 2: Our wet look stone sealer is suitable for Use on slate, pavers, brick, sandstone & concrete on the interior or exterior of your home.
3. Tips 3: PLEASE ALWAYS TEST A SMALL AREA TO DETERMINE SUITABILITY OF PRODUCT FOR INTENDED USE And Effect.

STEP2. SHAKE IT SLIGHTLY

Before use, please give it a gentle shake. This ensures the product achieves its maximum effectiveness!

STEP 3. APPLY EVENLY AND THINLY

Apply a thin layer of sealer to the object’s surface, allowing each layer to dry thoroughly before applying the next (recoat time depends on the thickness of the layer, typically recoatable after 30-60mins). It is recommended to apply 2 layers to enhance the effect.(NOTE: Under conditions of 68 ° F and 55% humidity, the drying time is affected by temperature, humidity, and the thickness of the coating. It is crucial to avoid applying the coating too thickly, ensuring there are no noticeable signs of excessive flow or pooling on the surface. This is particularly important for the initial layer. We recommend using a roller for application.)

1. Tips 1: It is recommend to prepare the mixture of water & sealer to 0.5:1 by volume when it applied with sprayer.(Brushes, roller or other application tools do not need to be watered down)
2. Tips 2: lt is recommend to apply 2 coats to reach a better effect, but do not apply more than 3 coats.
3. Tips 3: Please do not apply lf rain is expected within 24 hours after application, or if temperature is above 80° F or below 50°F(27°C and 10° C).
4. Tips 4: We recommend multiple coats for extremely absorbent pavers.
5. Tips 5: Please ensure uniform application of the sealer to prevent blotching. (We recommend using a roller for consistent results.)

STEP4. DRYING TIME

Surface dries in 30-60 minutes, reaching full dryness within 48-72 hours (Ideal humidity below 55%). Allow approximately 30-60 minutes between coats, ensuring the surface is dry before applying the next coat.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>