BROOD 24020 DRNX SLM Single Tap Nitro Cold Brew Beverage Dispenser Installation Guide
- July 20, 2024
- BROOD
Table of Contents
BROOD 24020 DRNX SLM Single Tap Nitro Cold Brew Beverage Dispenser
Specifications
- Power: Standard electrical outlet
- Usage: Beverage dispenser
- Compatibility: Can be connected to designated containers or any container with provided connectors
- Warning: Do not use liquid containing solid matter
Product Information
- Install on a clean and dry surface with at least 5 centimetres of space from all sides.
- Plug the power cord into an electrical outlet.
- Connect the beverage tube to DRNX SLM by pushing the elbow fitting into the connection underneath the machine. Tilt the machine if needed. To release the beverage tube, push the metal spring next to the connection.
- Place the Drip Tray beneath the spout.
- Warning: Ensure all tubes are pushed firmly in place to avoid blockage due to large coffee particles if pre-filter is not used.
- Pour your beverage into the designated container. Close the lid and push the seal.
- Push one elbow fitting into the connector at the bottom of the container and the other into the connector at the bottom of the machine.
- Caution:
- Pour your beverage into any container.
- Push the elbow fitting into the connector at the bottom of the machine.
- Drop the loose end of your beverage tube into the container.
- Caution: Make sure the arrow on the pre-filter base points in the flow direction and the container level is aligned with the machine height to prevent spout dripping.
Usage Instructions
DRNX SLM will pull from any container. If using a keg, attach the beverage tube to a keg coupler. If using a bag-in-box, attach the beverage tube to the bag-in-box adaptor.
FAQ
- Q: Can be used with liquid containing solid matter?
- A: No, liquid containing solid matter cannot be used with DRNX SLM by BROOD.
INSTALLATION
SETUP
-
Install on a clean and dry surface.
Allow no less than 5 centimeters of space from all sides. -
Plug the power cord into an electrical outlet.
-
Connect the beverage tube to DRNX SLM by pushing the elbow fitting into the connection underneath the machine.
Tilt the machine slightly if you need to. If you need to release the beverage tube, push the metal spring next to the connection underneath. -
Place Drip Tray beneath the spout.
WARNING: If you do not use the pre-filter, the following problem may
occur:
Blockage in the machine due to large coffee particles.
Make sure all tubes are pushed firmly in place.
CONNECT TO CONTAINER
Connecting to the designated BROOD container
-
Pour your beverage into the designated container.
Close the lid and push the seal. -
Push one of the elbow fittings into the connector at the bottom of the container. And push the other fitting into the connecter at the bottom of the machine.
-
Make sure the arrow at the base of the pre-filter is pointing in the direction of the flow.
CAUTION
Beverage container must be level with, or beneath the machine. Otherwise, the
spout will drip.
Connecting to any container
- Pour your beverage in any container.
- Push the elbow fitting into the connecter at the bottom of the machine.
- Drop the loose end of your beverage tube into the container containing your beverage.
- Make sure the arrow at the base of the pre-filter is pointing in the direction of the flow.
CAUTION
Beverage container must be level with, or beneath the machine. Otherwise, the
spout will drip.
- DRNX SLM will pull from any container. If using a keg, then attach your beverage tube to a keg coupler. If using a bag-in-box, then attach your beverage tube to a bag-in-box adaptor.
WARNING: Liquid-containing solid matter cannot be used.
WARNING: Never run hot liquid above 30°C (86 °F) through DRNX SLM.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>