ecler MPAGE4 4-zone Desktop Paging Station User Manual
- June 3, 2024
- ecler
Table of Contents
MPAGE4 4-zone Desktop Paging Station
User Manual
MPAGE4 4-zone Desktop Paging Station
IMPORTANT REMARK
WARNING: SHOCK HAZARD – DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING (If applicable): The terminals marked with symbol of “ ” may be
of sufficient magnitude to constitute a risk of electric shock. The external
wiring connected to the terminals requires installation by an instructed
person or the use of ready-made leads or cords.
WARNING: To prevent fire or shock hazard, do not expose this equipment to
rain or moisture.
WARNING: An apparatus with Class I construction shall be connected to a
mains socket-outlet with a protective earthing connection.
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug the apparatus during lightening sorts or when unused for long periods of time.
- Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Disconnecting from mains: When switching off the POWER switch, all the functions and light indicators of the unit will be stopped, but fully disconnecting the device from mains is done by unplugging the power cable from the mains input socket. For this reason, it always shall remain easily accessible.
- Equipment is connected to a socket-outlet with earthing connection by means of a power cord.
- The marking information is located at the bottom of the unit.
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.
WARNING: This product must not be discarded, under any circumstance, as
unsorted urban waste. Take to the nearest electrical and electronic waste
treatment centre.
NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may
be caused to people, animal or objects due to failure to comply with the
warnings above.
IMPORTANT NOTE
Thank you for choosing our Ecler MPAGE4, 4 zone desktop paging station!
It is VERY IMPORTANT to carefully read this manual and to fully understand its
contents before any connection in order to maximize your use and get the best
performance from this equipment.
To ensure optimal operation of this device, we strongly recommend that its
maintenance be carried out by our authorised Technical Services.
Ecler MPAGE4 comes with a 3-year warranty.
INTRODUCTION
The MPAGE4 is a desktop paging console compatible with ECLER MIMO54 and DAM614
digital audio matrix. Its keypad, LED indicators and goose-neck microphone
allow to select zones being paged, to know if these zones are busy, to capture
the voice message and broadcast it in real time to the destination zones.
The principal features of the MPAGE4 are:
- 4 zone selection keys (ZONE 1 to ZONE 4) (3)
- 1 key to select all 4 zones simultaneously (ALL) (4)
- 1 pager activation key (PAGE) (1)
- 6 LED status indicators (one per key)
- Goose-neck microphone (5)
- Configurable carillon melody (6)
- RJ-45 connector for connection of CAT5 standard cable to MIMO54 or DAM614 PAGER port (7)
INSTALLATION and CONNECTION
Installing a MPAGE4 unit consists of the following steps:
-
Installation of wiring using a standard CAT5 cable between the BASE connector of the MPAGE4 (7) and the PAGER connector on the rear panel of the MIMO54 / DAM614.
Wiring of RJ-45 connectorPin 1 to Pin 1| White/orange| MIC+|
Pin 2 to Pin 2| Orange| MIC-
Pin 3 to Pin 3| White/green| GND
Pin 4 to Pin 4| Blue| VCC (+10V)
Pin 5 to Pin 5| White/blue| ZONE 1
Pin 6 to Pin 6| Green| ZONE 2
Pin 7 to Pin 7| White/brown| ZONE 3
Pin 8 to Pin 8| Brown| ZONE 4
The cable transmits the zone selection control signals as well as the audio
signal of the goose-neck microphone and the signal for the carillon melody, if
activated. The phantom power required by the MPAGE4 unit is also supplied by
the MIMO54 / DAM614 using the same cable.
- Activation of the carillon melody (optional). With the two CHIME (6) microswitches on the rear panel of the MPAGE4 it is possible to: deselect the carillon melody (both set to OFF) or select one of three carillon melodies combining the ON and OFF positions (ON-OFF, OFF-ON and ON-ON). ON position = micro switch down.
- Level adjustment: the two adjustment potentiometers are accessed by removing the lid from the unit:
- MIC (9): adjusts the microphone signal gain
- CHIME (8): adjusts the level of the carillon melody signal (0-100%)
The console (5) microphone is a non-extractable electret cardioid type mounted
on a flexo. It is supplied with an “anti-pop” foam windshield.
The audio output is balanced and is sent through pins 1, 2 and 3 of the RJ-45
connector on the rear panel of the unit for reception by the MIMO54 / DAM614.
OPERATION
Once the MPAGE4 unit is connected to the MIMO54 or DAM614, the procedure for sending messages is as follows:
-
Selection of receiving zones by pressing:
• keys ZONE 1 to ZONE 4 (3) as desired (if LED indicators are lit it means that the zone is selected)
• or the ALL (4) key to select all 4 zones simultaneously (if the LED indicator is lit it means that ALL zones are selected)
All of the keys are mechanically interlocked (activated by pressing once and deactivated by pressing again) -
Hold the PAGE (1) key down ( “push to talk” type key without mechanical interlocking) while the voice message plays through the built-in goose-step microphone. The LED (2) on the key is lit while the key is pressed down (active message)
Note: if the carillon melody was activated, we recommend waiting a short period of time (3-4 seconds) after pressing the PAGE key and before starting the voice message in order to prevent the message from overlapping with the melody -
If necessary, cancel the individual zone selection (ZONE 1 to 4) or the selection of all zones (ALL) by pressing the keys again, verifying that the LEDs go out. If the
selection is not cancelled, the next message that is sent will be delivered to the selected zones.
With MIMO54 or DAM614 it is also possible to set zones permanently selected to
always receive voice messages sent from the MPAGE4 unit, regardless of whether
or not they have been selected via the buttons.
To set it, on the front panel of the MIMO54 or DAM614, select the ZONE switch
for the required zone(s) in the ON position and then press the button of input
6. The corresponding LED lights in blue to indicate that the selected zone has
been permanently enabled as a PAGER. Repeat the process for each zone you wish
to permanently enable.
NOTE: Remember that on the MIMO54, when the EVAC working mode is active
for input number 5 (Evacuation/Emergency), the ZONE destination zone selector
and the zones selected for the MPAGE4 Unit are disabled. In this working mode,
the signal from the PAGING programme and warnings in ALL of the unit’s zone
outputs are muted and replaced by the signal in input 5 or the
evacuation/emergency message.
FUNCTIONS LIST
- PAGE key
- PAGE indicator
- Zone keys
- ALL key
- Goose-neck microphone
- CHIME selector
- R-45 connector, PAGER
- Adjust level of the CHIME carillon melody signal
- Adjust MIC microphone signal gain
FUNCTIONS DIAGRAM 
TECHNICAL CHARACTERISTICS
MPAGE4
Microphone type| Non removable gooseneck condenser microphone
Polar pattern| Unidirectional
Microphone frequency response| 50Hz – 18KHz (-10dB)
Output level| 0dBV @ 104dB SPL ±7dB (internal adj.)
Chime| DIP selector for mode 1, 2 or 3 or none
Maximum audio cable length| Twisted pair 20m
| Shielded 800m (provided that minimum voltage is assured)
Number of paging zones| 4
Indicators| Selection LED on all keys
Power supply| +6 to +15V
Maximum power consumption| 40mA
Connector| RJ-45
Dimensions (microphone excluded)| W 120mm x D 126mm x H 43mm
Weight| 650g
Included accessories| Windscreen, connector
All product characteristics are subject to variation due to production
tolerances.
NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements
in the design or manufacturing that may affect these product specifications
For technical queries contact your supplier, distributor or complete the
contact form on our website,
in Support / Technical requests.
Motors, 166‐168 08038 Barcelona ‐
Spain ‐ (+34) 932238403
information@ecler.com
www.ecler.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>