Darkglass Vintage Ultra V2 Bass Preamp Pedal User Manual

: July 16, 2024
: DARKGLASS

Table of Contents

Darkglass Vintage Ultra V2 Bass Preamp Pedal
Product Information
Product Usage Instructions
Specifications
Warning
Warranty
Disclaimer
EMC/EMI
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Darkglass Vintage Ultra V2 Bass Preamp Pedal

Darkglass-Vintage-Ultra-V2-Bass-Preamp-Pedal-Product

Product Information

Specifications

Controls: Grunt Switch, Bass, Lo Mids, Hi Mids, Treble
Bass: +-12dB @ 100Hz
Lo Mids: +-12dB switchable 250Hz, 500Hz, and 1kHz
Hi Mids: +-12dB switchable 750Hz, 1.5KHz, and 3kHz
Treble: +-12dB @ 5kHz
Input Impedance: 1M
Output Impedance: 1k
Current Consumption: ~120mA
Voltage: 9V DC (Center Negative)
Dimensions: Width: 125 mm, Length: 96 mm, Height: 57 mm, Weight: 430 g

Warning
The Vintage Ultra requires a regulated 9V DC adapter with a center-negative plug to prevent suboptimal noise performance or damage to the unit.

Warranty
To activate the warranty, register your product at http://mypedal.darkglass.com and contact support@darkglass.com before shipping any product for service.

Disclaimer
The manufacturer reserves the right to change specifications without notice. The product meets various standards including EN55013, RoHS, and WEEE.

EMC/EMI
The equipment complies with Class B Digital device standards and may cause interference if not installed correctly. Follow instructions to minimize radio frequency interference.

Product Usage Instructions

Power Requirements
The Vintage Ultra operates on a 9V DC power supply with a center-negative plug. Ensure the adapter provides at least 120mA of current.
Connecting the Pedal
Connect your instrument to the input jack of the Vintage Ultra using a standard instrument cable. Use another cable to connect the output jack to your amplifier or recording device.
Adjusting Controls
Use the Grunt Switch to set the level of low-frequency saturation. Adjust the Bass, Lo Mids, Hi Mids, and Treble controls to tailor your sound by boosting or cutting frequencies at different ranges.

Frequently Asked Questions (FAQ)

Q: What should I do if my Vintage Ultra pedal is not functioning properly?
A: If you experience issues, ensure you are using a compatible power supply and check your instrument and cables for any faults. If problems persist, contact our support team for assistance.
Q: Can I use batteries to power the Vintage Ultra?
A: The Vintage Ultra does not support battery power and requires a regulated 9V DC adapter with a center-negative plug for optimal performance.

CREATIONS
DEALERS
SUITE
APPAREL

Specifications

Controls

Master: Whereas the Level Knob controls the output of the overdrive section the Master volume adjusts the overall volume of the unit. Ideal for fine-tuning the output in clean mode. It also serves as a DI-level control.
Blend: Mixes the clean input signal with the overdriven signal. The clean signal remains at unity gain while the volume of the overdriven signal is set by the Level knob, allowing for fine control of the blend ratio.
Level: Sets the volume of the overdriven signal.
Drive: Sets the amount of saturation in the overdriven signal.
Attack Switch: Sets the amount of treble content to saturate: The “Boost” setting emphasizes the treble content’s extra clarity and presence. The “Flat” position leaves this register untouched while the “Cut” positionwill reduces the amount of high frequencies being saturated.
Grunt Switch: Sets the amount of low-frequency content to saturate by selecting between three different bass boost levels before the clipping stage.
Bass: +-12dB @ 100Hz
Lo Mids: +-12dB switchable 250Hz, 500Hz and 1kHz
Hi Mids: +-12dB switchable 750Hz, 1.5KHz and 3kHz
Treble: +-12dB @ 5kHz

Technical Specifications

Input Impedance: 1MΩ
Output Impedance: 1kΩ
Current Consumption: ~120mA
Voltage: 9V DC (Center Negative)

Dimensions

Width: 125 mm / 4,92″
Length: 96 mm/ 3,77″
Height: 57 mm / 2,24″
Weight: 430 g / 0,94 lb

Warning

The Vintage Ultra has a current draw of 120mA. Only use a regulated 9V DC adapter with a center-negative plug. Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.

Warranty

To activate the warranty, we encourage you to register your product at: http://mypedal.darkglass.com and enter the serial number on the back of your pedal. Please contact us via email support@darkglass.com before shipping a product to us.

Disclaimer

In the interest of continuous improvement, specifications are subject to change without notice. If you have any questions, please don’t hesitate to contact us at www.darkglass.com The manufacturer claims that the above product fulfills the requirements as set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE.
1176®, and SSL® are registered trademarks of their respective companies. Names of factory modes are intended for descriptive purposes only and should not be construed as an endorsement or affiliation with the companies or products named.

EMC/EMI

This equipment has been tested and found to comply with the limits for a Class B Digital device, according to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmfulinterference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.