Darkglass Noise Gate NSG Pedal User Manual

: July 16, 2024
: DARKGLASS

Table of Contents

Darkglass Noise Gate NSG Pedal
Product Usage Instructions
FAQ
Specifications
Warranty
FCC STATEMENT
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Darkglass Noise Gate NSG Pedal

Darkglass-Noise-Gate-NSG-Pedal-PRODUCT

Product Usage Instructions

Warning: The Noise Gate has a current draw of 60mA.

Only use a regulated 9V DC adapter with a center-negative plug.
Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.
To activate the warranty, register your product on: mypedal.darkglass.com and enter the serial number on the back of your pedal.
Contact support@darkglass.com before shipping a product for warranty claims.
The manufacturer claims that the product meets the requirements set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE.
Specifications are subject to change without notice.
This equipment complies with Class B Digital device standards.
Follow installation instructions to prevent harmful interference.
If interference occurs, try reorienting antennas, increasing separation between devices, or consult a professional.

FAQ

Q: What is the threshold range of the Noise Gate in Soft and Hard modes?
A: The threshold range is from -65 dBV to -30 dBV in Soft mode and from -45 dBV to +5dBV in Hard mode.
CREATIONS
DEALERS
SUITE
APPAREL

Specifications

Controls / Front

Threshold

Use this push knob to control the threshold of the noise gate.
Press the knob to switch between the “Soft” mode(Blue LED color) for softer gain reduction and “Hard” (Red LED color) for the more aggressive gate operation.

Threshold range

From -65 dBV to -30 dBV in “Soft” mode
From -45 dBV to +5dBV in “Hard” mode

Technical Specifications

Input Impedance: 1MΩ
Output Impedance: 100kΩ
Current Consumption: ~60mA
Voltage: 9V DC (Center Negative)

Dimensions

Width: 50 mm / 2″
Length: 36,5 mm/ 1 ½
Height: 45 mm / 1,75″
Weight: 205 g / 0,45 lb

Warning

The Noise Gate has a current draw of 60mA. Only use a regulated 9V DC adapter with a center-negative plug. Unregulated power supplies and/or higher voltages mayresult in suboptimal noise performance and even damage your unit, voiding the warranty.

Warranty

To activate the warranty, we encourage you to register your product at: http://mypedal.darkglass.com and enter the serial number on the back of your pedal.
Please contact us via email support@darkglass.com before shipping the product to us.

Disclaimer
In the interest of continuous improvement, specifications are subject to change without notice. If you have any questions, please don’t hesitate to contact us at www.darkglass.com The manufacturer claims that the above product fulfills the requirements as set by EN55013, EN55020, EN60555-2, EN60555-3, RoHS, WEEE.

FCC STATEMENT

This equipment has been tested and found to comply withthe limits for a Class B Digital device, according to part 15 ofthe FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. There is noguarantee that interference will not occur in a particularinstallation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.