Flytec V003 Racing Boat User Manual

Flytec V003 Racing Boat

High Speed Boat Diagram

PREPARATION

1. Open the hatch
2. Put the battery into the battery compartment, screw the battery fixing button, and plug in the power cord
3. Close the hatch cover and tighten the knob
4. Install the battery on the remote control and turn on the remote control switch
5. Put the boat into the water, the remote control will link with the boat
6. After the frequency binding is completed, the buzzer emits a”beep” sound, the indicator light of the remote control turns green,and the boat light is always on

Remote Control Battery and Boat Battery Details

Steps for installing the remote con1rol batteries
Please remove the battery cover at the bottom of the remote control first, then put in 4X “AA” batteries correctly according to the corresponding positive and negative positions, and put on the battery cover
Boat Battery Removal and Charging Procedure

1. Tum the hatch cover knob 90 degrees to remove the hatch cover
2. Tum the battery fixing knob of the battery compartment 90 degrees clockwise
3. Unplug the boat power cable and take out the battery
4. Connect the battery interface to the USB charging cable, and connect to the power supply to start charging, the red light on the USB port indicates that it is charging, and the red light turns off after charging is completed

Remote Control Operating Instructions

Switch

Toggle the switch, put the boat into the water, the green light of the remote control is always on after the frequency is connected, and there is a “beep” sound, and you can play

Fixed-speed cruise button

Toggle the button forward to achieve the constant speed cruise; if it is necessary to cancel it, push the button backward to cancel

Forward &Backward

Push the throttle stick backward, the boat moves forward; push the throttle stick forward, the boat goes backward

Tum Left &Tum Right

Tum the steering wheel counterclockwise and the boat will tum left: tum the steering wheel dockwise to tum right
Self-righting Button

When the boat flips, press the Self-righting button, the boat can flip back

Left trim & Right Trim

If you find the boat is deflected during driving, you can use the trim button to adjust the angle

0ne-click demo

Drive the boat to empty place.Press the Demo button, the boat will drive in afigure-of-eight path
Speed Switch Button

In the nonnal driving state, press the speed swikh button, and there will be 2 beeps sound to indicate that in the middle speed, and then press the speed swikh button, and 3 “beeps” sound will be heard, indicating that in high speed. Continue to press the speed swikh button to return to the initial state, that is in slow speed.
Lighting button

After the frequency binding ls completed, the light ls always on, press it to switch to the bnlathlng light mode, and press it again to tum off the light effect

FAQ

• Remote control low battery warning
  When the battery of the remote control is low, the indicator light of the remote control will flash continuously to remind you to drive the boat back to the shore as soon as possible to replace the battery of the remote control and use it again after the frequency matching.

• Boat low battery warning
  When the remote controller emits a “beep” “beep” sound, and the boat automatically tums to low speed mode, it means that the boat is in low battery capacHy. In order to avoid running out of battery power, please drive the boat back to the shore as soon as possible to replace the battery, and continue to use it after re-linking.

• Over Distance waming
  When the boat is driving far away, the indicator lights on the remote control flash alternately, indicating that the baat is about to go out of the range of control, please drive back immediately!

• Stuck protection
  When the motor is blocked by a foreign object for 1 second, it will enter the stuck state. In order to avoid the motor from being bumed, the boat will automatically stop, and the remote control will emit a long “beep” sound.

Maintenance

After using the remote control boat, you should remove the hatch cover, 1ake out the batlery in the boat, and check whether there is anv waler ingress inside the boat. If there is, please wipe off the waler drops and let it dry for a while, and then cover the hatch cover after drying to prevent damage to the internal electronic parls. When you use it next time, fix the fully charged battery on the battery holder and comect itto the power supply for use.

Propeller replacement
When the propeler is agi,g or damaged. it can be replaced. the operation is as shown in the figure below

1. The set comes with an extra propeller + a hex wrench
2. First 1um off the power and pull out the battery, then press the shaft inside the boat with one hand, and disassemble it with a wrench with the other hand

Troubleshooting

Battery Precautions

• Do not disassemble or reassemble the battery.
• Do not short-circuit the battery.
• Do not throw the battery into water.
• Do not hit or throw the battery.
• Do not touch the leaking battery directly.
• It is forbidden to use pointed objects to insert the battery or damage the battery in other ways.
• Please use the charging cable attached to the product to charge the battery.
• Do not charge near fire or under sunlight
• Do not use damaged or severely deformed batteries

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>