SINBON AUTO-NACS01 NACS Charging Cable with Vehicle Connector Owner’s Manual
- July 10, 2024
- SInBOn
Table of Contents
- SINBON AUTO-NACS01 NACS Charging Cable with Vehicle Connector
- Specifications
- Product Usage Instructions
- FAQs
- Product Overview
- Applicable Standard
- Product Features
- Technical Data
- INSTALLATION INSTRUCTION
- Service Terms
- Warranty
- FCC
- CONTACT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SINBON AUTO-NACS01 NACS Charging Cable with Vehicle Connector
Specifications
- Model Number: A9604566
- Product Type: Charging Cable Assembly
- Compatibility: NACS Vehicles
- Rated Voltage: AC 240 VAC
- Rated Current: 80A
- Conductor Connection Method: Customized
- Insulation Resistance: 500 M
- Rated Drop Resistance: 100 drops at room temperature 1m
- Insertion / Withdrawal Force: 90N
- Flammability Rating: VW-1 for Cable, V-0 for All Plastic Parts
- Ambient Temperature: Customized
- Operating Temperature: DC 3.3V
- Maximum Elevation: NTC or PT1000
- Operating Humidity: Customized
- Protection Degree: 315MHz
- Cable Diameter: 19.5mm
- Cable Length: 5m, Others (Customized)
Product Usage Instructions
- Installation Process
- Ensure the electric vehicle is powered off before installation.
- Connect the vehicle connector to the electric vehicle’s charging inlet securely.
- If remote opening of charge port doors is needed, ensure the RF transmitter is properly set up.
- Route the open cable end to the electric vehicle supply equipment for installation.
- Charging Process
- Plug the open cable end into the electric vehicle supply equipment.
- Ensure that the charging connector assembly is securely connected.
- Power on the electric vehicle supply equipment to initiate the charging process.
- Monitor the charging progress and disconnect the cable once charging is complete.
FAQs
- Q: Can this charging cable assembly be used with all-electric vehicles?
- A: This cable assembly is specifically designed for NACS vehicles and may not be compatible with all-electric vehicles. It is recommended to check compatibility before use.
- Q: What should I do if the temperature sensor triggers over-temperature protection?
- A: If the temperature sensor detects overheating, stop the charging process immediately and allow the system to cool down before attempting to charge again.
Product Overview
- SINBON NACS Charging cable assembly with Vehicle connector and open cable end for charging electric vehicle and plug-in hybrid electric vehicle with alternating current by Tesla vehicle charging inlets, for installation at electric vehicle supply equipment, following NACS.
- The NACS 32A/40A/50A/65A/80A charging connector provides a Level 2 or 3 charging solution for NACS vehicles.
- The connector is manufactured with a built-in temperature sensor for ver-temperature protection and an RF transmitter to remotely open charge port doors.
- The transmitter is available in two frequencies for regional compliance.
Applicable Standard
- TS -0023666
- North American Charging Standard
- IEC 62196
- Plugs, socket socket outlets, vehicle connectors, and vehicle inlets – Conductive charging of electric vehicle vehicles
- IEC 61851
- Electric vehicle conductive charging system
Product Features
- Safe and Stable
- High-structure Strength
- Low Heat Productivity
- Built-in Temperature Sensor
- Ergonomic
- Highly Waterproof
- UV-resistant
- Flame Retardant
Technical Data
PERFORMANCE SPECIFICATION
| Model Number | A9604566 |
|---|---|
| Product Type | Charging Connector Assembly |
| Compatibility | AC |
| Rated Voltage (Nominal) | 240 VAC |
| Rated Current | 80A |
| Power Conductor Connection Method | Customized |
| Insulation Resistance | ≥ 500 MΩ |
| Rated Drop Resistance | 100 drops（Room temperature 1m） |
| Insertion / Withdrawal Force | ＜ 90N |
| Flammability Rating | VW-1 For Cable V-0 for All Plastic Parts |
ENVIRONMENTAL SPECIFICATION
| Ambient Temperature | -40°C to +85°C |
|---|---|
| Operating Temperature | -40°C to +50°C |
| Maximum Elevation | 3,000 m |
| Operating Humidity | 95%@50℃, non-condensing |
| Protection Degree | IP67 |
| UV Resistance | F1 per UL 746C |
ELECTRICAL SPECIFICATION
| Low Voltage Electrical Connector | Customized |
|---|---|
| Low Voltage Electrical Terminal | Customized |
| Rated Voltage (Nominal) | DC 3.3V |
| Temperature Sensor Type | NTC or PT1000 |
| Temperature Sensor Threshold | Customized |
| RF Transmitter Frequency | 315MHz |
MECHANICAL SPECIFICATION
| Dimensions (Overall) | 46.5mm×72.1mm×213.9mm |
|---|---|
| Cable Diameter | 19.5mm |
| Cable Length | 5m, Others(Customized) |
INSTALLATION INSTRUCTION
Service Terms
Whole Solution
- SINBON could provide customers and cooperative partners with a whole solution of technical support, training, maintenance service, etc.
One-stop Service
- SINBON could provide customers and cooperative partners with a one-stop service. All charging-related products purchased from SINBON are offered professional and guaranteed service for any problem caused due to product usage and quality.
Warranty
- Two years from shipment / Accumulation 10000 charging cycles after initial use.
- During the warranty period, products must be carried out on-site technical service due to product faults or quality defects (caused by abnormal or improper usage is not included), SINBON will promptly dispatch a technical engineer to solve product malfunction for free.
FCC
FCC Statement
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning
This device complies with the Innovation, Science and Economic Development
Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
- This device has been assessed to comply with SAR and/or RF field strength limits. The device can be used in the exposure condition without restriction.
ISED RF exposure statement:
- This device has been assessed to comply with SAR and/or RF field strength limits. The device can be used in the exposure condition without restriction.
CONTACT
- Jiangyin SINBON Electronics Co., Ltd.
- 288 Chengjiang Middle Rd.,
- Jiangyin, Jiangsu, China
- Tel: +86-510-86404098
- Fax: +86-510-86404940
PROPRIETARY DOCUMENT
- The purpose of this specification is to define the scope of supply offered by SINBON.
- This document may not, in whole or in part, be duplicated or disclosed without the written permission of the SINBON Product Specification author.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>