Funsionbeat FUSNB 3 in 1 Powerbank+ True Wireless Earbuds+ Bluetooth Speaker User Manual

Funsionbeat FUSNB 3 in 1 Powerbank+ True Wireless Earbuds+ Bluetooth

Speaker

Specifications

• Speaker Type: Stereo
• Speaker System: Powerbank+True wireless earbuds+Bluetooth speaker
• Dimensions : 1036133mm
• Weight : 300g (earbuds 6g)
• Driver : 5W 40mm (speaker), 32.3mW 8mm (earbuds)
• Audio Playback Time : Speaker approx. 25+ hours, Earbuds 5 hours, Total 150h+ by charging case
• Bluetooth Version : V5.3
• Battery Capacity: Speaker 3.7V 5000mAh, Earbuds 3.7V 40mAh
• Charging Time : Speaker approx. 2.5 hours (USB C), Earbuds approx. 1 hour
• Frequency Response: 100-20KHZ
• Range : Up to 10m
• USB Port : USBC input/Output: 5V/2A, USB A Output: 5V/2A
• Built-in Microphone for both earbuds and speaker

Product Usage Instructions

Fusionbeat-Speaker:

1. Turn on the speaker, you will hear the boot.
2. Buds will power on when taken out from the case.

Fusion beat-Buds:
After opening the phone Bluetooth, click the Fusionbeat-Speaker Fusionbeat- Buds to pair the speaker and buds.

What’s in the box

Key functions-Speaker

• LED light
  • Paring : blue light fast flash
  • Paired : blue light on
  • Tws on: Blue light slow flash
  • Earbuds charging : red light on
  • Fully charged (earbuds): red light on
• Rotary knob
  • Volume +: clockwise rotation
  • Volume-: counterclockwise rotation
  • Answer/end call: single click
  • Reject calls : hold 2s
• BT button
  • Paring mold : hold 2s Siri:2 click
  • Tws on/off :3 click

Key functions-Earbuds & powerbank

1. Power on/off: hold the earbuds 2s to power on/off
2. Play/Pause: 2 click the play/ pause the music(L/R)
3. Call/answer: When an incoming call,2 click will answer or hang up, press and hold to reject the call.
4. Volume down: 1 click(L)
   • Previous track: hold 2(L)
   • Volume up: 1 click(R)
   • Next track: hold 2s(R)
   • Siri :3 click(L/R)
5. Power bank button:
   • Power on: one click
   • power off: 2 click(when power on)
6. USB port: USB A Output:5V/2A USBC input/Output:5V/2A
7. battery status:

Bluetooth Connection

1. Turn on the speaker, you will hear the boot. Buds will power on which take them out from the case.
2. After open the phone Bluetooth, Click the “Fusionbeat-Speaker” and “Fusionbeat-Buds”to pair the speaker and buds.

Notes :

1. If it is not paired for 15 minutes after booting, it will shut down. When low battery, you can hear the prompt tone then the speaker will power off automatically
2. If Apple users feel that the volume is low, you can turn off this setting on the phone(Settings-Sounds & Haptics-Headphone Safety-Reduce Loud Sounds)

Safety Instructions

1. Keep the product away from extremely hot and cold environments, it will damage the battery and circuit.
2. Avoid liquid immersion into the product.
3. Do not disassemble the product.
4. Do not use concentrated chemical products or detergents to clean the product.
5. Use only 5V/1A power supply. Connecting the power supply voltage too high may cause serious damage.
6. Do not randomly discard or place the product near fire or high temperature to avoid the danger of explosion.

FCC statement

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interterence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

FAQ

Q: What should I do if the product is not paired after booting?
A: If the product is not paired for 15 minutes after booting, it will shut down. When low battery, you can hear the prompt tone, and then the speaker will power off automatically.

Q: How can I increase the volume for Apple users?
A: If Apple users feel that the volume is low, you can turn off this setting on the phone (Settings-Sounds & Haptics-Headphone Safety-Reduce Loud Sounds).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>