EARMOR AC136 Bluetooth Hearing Protector User Guide
- July 9, 2024
- Earmor
Table of Contents
EARMOR AC136 Bluetooth Hearing Protector
What’s Included
Using Your Hearing Protector
- Turn ON： Press and hold the 2S MFB
- Turn OFF： Press and hold for 3S MFB
- Auto switch-off after 5 minutes without connecting to the device
Charging the hearing protector
To charge the hearing protector, insert the supplied USB connector cable into the USB jack located on the hearing protector. Connect the other end of the cable to a suitable USB power source such as a computer or third-party certified (UL, Intertek, etc.) AC to USB wall adapter. （5V 1A）
Pair with your device
- Press and hold the power button 3s， Indicator will flashlight red and green fast
- Open the Bluetooth on your device and select “AC136” start to pairing.
- When turned on, the hearing protector will automatically connect to the last connected device if available. If not, it will enter pairing mode
- Have connection problems? Remove “AC136” from your device’s Bluetooth history, ensure it’s less than 3 feet away then try pairing again
Controls
| buttons | operation | Action |
|---|---|---|
| MFB | play/pause music | single press |
| > | volume + | single press |
| < | volume – | single press |
| > | Next song | Long Press 1 second |
| < | Previous song | Long Press 1 second |
Call
| buttons | operation | Action |
|---|---|---|
| MFB | answer call | single press |
| MFB | end call | single press |
| MFB | reject call | Long Press 1 second |
Voice assistant
| MFB | Long press 1s in connection status |
|---|---|
| MFB | Press and hold again for 1s to close |
LED Indicator Status & Voice Prompt
| Work Status | Indicator Light Status | Voice Prompt |
|---|---|---|
| Power on | Red and green light is flashes 1 second | Power on |
| Power off | Light off | Power off |
| Pairing mode | Green and red light flashes quickly | Pairing |
| Bluetooth connected | Greenlight is flashes per 5 seconds | Connected |
| Low battery warning | Red light is flashes per 10 seconds | Please charger |
| Disconnected | Green and red light flashes quickly | Disconnected |
| Battery high | Battery high（70%-100%) | |
| Battery medium | Battery medium(30%-70%) | |
| Battery low | Battery low(0%-30%) |
Specifications
| Version | 5.4 |
|---|---|
| Input | 5V 1A |
| Charging time | 2 hours |
| Working range | 20 meters |
| Working time | 120 hours |
| Charging Port | Type-C |
| Battery capacity | 1200mAh |
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
This Marking shown on the product or its literature indicates that it should
not be disposed of with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of waste and recycle it
responsibly to promote the sustainable reuse of material resources. Household
user should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can make this
item for environmentally safe recycling. Business users should contact their
suppliers and check the terms and conditions of the purchase contract.t This
product should not be mixed with other commercial wastes for disposal.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
RF warning statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
WARNING DO NOT DISPOSE OF THE UNIT IN FIRE OR WATER. > NEVER ATTEMPT TO DISASSEMBLE AND REASSEMBLE.’WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSEHOLD WASTE. ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSEHOLD WASTE; RECYCLE WHERE FACILITIES EXIST. > CHECK CHECK WITH YOUR LOCAL AUTHORITIES FOR RECYCLING ADVICE. KEEP YOUR DEVICE AND ALL ACCESSORIES OUT OF THE REACH OF CHILDREN AND ANIMALS.> SMALL PARTS CAN CAUSE SUFFOCATION OR INJURY. SMALL PARTS CAN CAUSE CHOKING OR SERIOUS INJURY IF SWALLOWED. > AVOID EXPOSING YOUR DEVICE TO VERY HOT OR VERY COLD TEMPERATURES (BELOW 0°C OR ABOVE 0°C). (BELOW 0°C OR ABOVE 45°C). > EXTREME TEMPERATURES MAY CAUSE DEFORMATION OF THE DEVICE AND REDUCE THE CHARGING CAPACITY AND LIFETIME OF YOUR DEVICE. AND REDUCE THE CHARGING CAPACITY AND LIFE SPAN OF YOUR DEVICE. > DO NOT ALLOW YOUR DEVICE TO GET WET LIQUIDS CAN CAUSE SERIOUS DAMAGE. > DO NOT HANDLE YOUR DEVICE WITH WET HANDS.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>