DoHonest 5 Inch 2 Channels HD Digital Wireless Monitoring System User Manual
- July 8, 2024
- DoHonest
Table of Contents
DoHonest 5 Inch 2 Channels HD Digital Wireless Monitoring System
Please read this user manual carefully before use to ensure your safety.
IMPORTANT NOTES
- Wireless reversing system technology is an auxiliary drive device, It is not a substitute for the driver responsible for the operation vehicle;
- To ensure proper operation ofthe camera, clean the camera to release it. From dirt, water droplets snowdrops etc;
- In order to ensure the normal function ofthe display, please pay attention to the fixed display to avoid falling and water;
- Keep the monitor and camera cables away from hot objects such as the engine.Or exhaust.；
- If your camera model does not have a built-in LED, suggest you to turn on the license plate light when at night or in the dark；
- The Wireless camera device are aplicable to vehicles with DC12V-24/ power output (Allowance is +/-10% )
SPECIFICATIONS
| Monitor (Receiver)Parameters | Camera(Launcher) Parameters |
|---|---|
| Display: | 5-inch IPS full-view angle |
| Resolution: | *800480** |
| Brightness: | 500cd/m |
| Operating Voltage: | DC 12V-32V |
24V
Power consumption:| 240 ±20mA@DC12V| Power Consumption|
100MA
Operating temperature:| -20-+70°C| Minimum illumination|
0.01 Lux**
Transmitting /Receiving Frequency 2400・2483.5 MHz
ON DIAGRAM
- “Button +”：Move the cursor up or as increase button ;
- “Menu M”：Click to enter the menu , (Without operation for 10S, will automatically exit). In the submenu operation, press “Set” to confirm, and press “M” to return.
- “Button-“： Move the cursor down or as a decrease button .
- “Button ” Ruler line adjustment: Click “H” “W” “M” to bring out the submenu. 1. Click + to adjust the height of the ruler line upward. 2. Click – to adjust the height of the ruler line Height, size, left and right
- “Button SEL”： Press the key to confirm
Menu function options
Pairing operation: press the “Button M” to enter the menu, select the
“Pairing”setting(The icon will turn yellow), press the “Button SEL” will into
the pairing state,it will display a countdown till the camera and monitor are
connected successfully. (Note: Please let the camera power
Picture adjustment operation: press the “Button SEL” to enter the menu, select
the “image adjustment” (The icon will turn yellow), press the “Button SEL” to
enter the submenu, select the Brightness, Contrast or Hue, Press “Button SELw
into the setting, press to increase/decrease.
Image mirroring/flip operation: short press the “Button M” to enter the menu,
select the image display model short press the “Button SEL” to confirm.Long
press the “middle button” to return to the previous menu.
System setting
- A. System language: Different language optional；
- B. Trigger delay function: Press ” Button M” into the setting, and press “+” “-” to set the time ；
- C. Autocycle function: Press “Button M ” to enter the submenu, can select “Turn on ” or “Turn Off “.The screen will display “Scan” when turned on ；
- D. Autocycle time: Can set autocycle time when autocycle functions in a turn-on state.
- Car parking guideline setting: Caml/Cam2, press the “Button “can display or hide the guideline; power off will memory setting.
- Display mode switch: press the “Button SEL”, Can select CAM1/ CAM2/ 2 screen split display mode.
- Power on the monitor, the screen will black screen after 5S without connection; Under normal mode, the monitor will display a NO Signal when the camera turns off, and it will into a black screen after 3S, when the camera powered on, the monitor will display automatically
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>