BIGTREETECH TOUCHV1 5 Inch Touch Screen with Multi Printer User Manual
- July 12, 2024
- BIGTREETECH
Table of Contents
TOUCHV1 5 Inch Touch Screen with Multi Printer
PANDA TOUCH
User Manual
PANDA TOUCH
Slide the power switch to the middle fo「Panda Touch to run
on its lithium battery, enabling portability. Slide it to the right
for direct power from the magnetic charging dock, preserving
the internal ba忧ery’s lifespan. To the le仕turns off Panda Touch.
CHARGING DOCK
*The power input has been outfitted with hot-plug protection,
allowing users to hot-plug the power supply.
INSTALLATION INSTRUCTIONS
1 Installing Panda Touch
1 Use a screwdriver and the two M3x6 FHCS to assemble
the Charging Dock and the Mounting Bracket as shown.
2 Remove the film from the back of the Mounting
Bracket.
3 Ensure the p「inter surface is clean and free of oil,
grease, etc., attach the assembled Charging Dock
centrally atop the original screen. Apply pressure to
adhere fully and allow 12 hours for optimal adhesion.
4 Attach Panda Touch to the Charging Dock.
2. Wiring and Power Connection
SPECIFICATIONS
MCU
|
Xtensa 32 bit dual core LX7 ESP3253R8, up to 240MHz clock speed.
---|---
Memory
|
SiP PSRAM-8MB, SiP Flash-16MB
Display Size
|
5”
Resolution
|
800 x 480
Viewing Angle
|
lPS Full View
Display Colo「S
|
16.7M
Communication
|
2.4G Wi-Fi (lEEE 802.11 b/g/n)
Operating
Temperature
|
。－70°(
Operating Current
|
SV O.SA (Peak 0.7A)
Logic Voltage
|
3.3V
Built-in Ba忧ery
|
Allows Panda Touch portable
use for up to 0.5 hours.
Charging Time
|
1.2 hours
Expansion
lnterfaces
|
12( (For DlY connection of
temperature/humidity sensors, etc); us日 Drive (For 「eading USB drives)
PRECAUTIONS
Battery Usage and Maintenance
1. When operating on its built-in lithium battery, Panda Touch only has a
battery life of 0.5 hours. To preserve the battery and prolong product
lifespan, it is recommended to change Panda Touch immediately on turn it
off once the battle is depleted.
2. The screen may flicker when the lithium battery’s power is low. This is
no「mal and serves as a 「eminder for use「S that the batte「y is nearing
depletion. ln response, users ShOL』Id promptly charge the batte「y口「 turn off
Panda Touch.
3. When powe「ing Panda Touch th「ough the cha「ging dock connected to the
30 p「inter, if the printer is turned off, we 「·e commend switching Panda
Touch’s
powe「 switch to OFF. This prevents potential damage from prolonged power
deficiency.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that
may cause undesired operation.
Scan the QR code to access the on line manual
for more product info and instructions.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide
reasonable protection against harmful interference in a residential
installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause
harmful interference to radio or television reception, which can be determined
by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to
which
the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
For Makers. By Makers.
Should you encounter any issues during installation,
please feel free to contact us for assistance.
service005@biqu3d.com
http://www.bigtreetech.com/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>