Uascent UAM087 Matter Cost Effective WiFi Plus BLE Module User Guide

Uascent UAM087 Matter Cost Effective WiFi Plus BLE Module

Revision History.

Overview.

Introduction.
UAM083 is a cost-effective WIFI+BLE low-power module developed by Uascent Technology, supporting IEEE 802.11 b/g/n and BLE 5.2 protocol standards, as well as STA, AP, and Direct modes. Users can use this module to add networking functions to existing devices or build independent network controllers.

Features.

• Supports 20 MHz channel.
• Standard IEEE802.11b/g/n.
• Support Wi-Fi + Bluetooth
• Support STBC.
• Built-in low-power 32-bit MCU speed up to 160MHz, can be used as an application processor.
• Support STA and AP and Direct  working modes.
• Support BLE 1 Mbps

Recommended Operating Rating.

Reference power consumption for conventional continuous operation.

TX Mode
IRF| 11b 11M| 270| mA
IRF| 11g 54M| 240| mA
IRF| 11n HT20 MCS7| 230| mA
RX Mode
IRF| 11b 11M| 80| mA
IRF| 11g 54M| 80| mA
IRF| 11n HT20 MCS7| 80| mA

Low-power consumption

ESD Specifications

Module use precautions.

When using the WIFI module of Uascent Technology, a certain tolerance should be reserved for the output current of the power supply. It is recommended that the output current of the power supply be ≥ 500mA, and a suitable power supply IC packaging should be selected. When using LDO power, attention should be paid to the issue of thermal, and when using DC-DC power, attention should be paid to the issue of overshoot at the moment of power on.

Wi-Fi Specification.

PHY Data rates

| Wi-Fi:     802.11b: 11, 5.5, 2, 1 Mbps

802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps HT20 MCS0-MCS7

Transmit Output Power| Wi-Fi :     802.11b@11Mbps 16±2dBm 802.11g@54Mbps 15±2dBm

802.11n@HT20 MCS7 14±2dBm

EVM| 802.11b /11Mbps: EVM≦-10dB

802.11g /54Mbps: EVM≦-25dB

802.11n /HT20 MCS7: EVM≦-27dB

Receiver Sensitivity| 802.11b@8% PER11Mbps≤ -88dBm
| (HT20)| 802.11g@10% PER 54Mbps≤-74dBm
---|---|---
802.11n@10% PER MCS 7 ≤-71dBm
Operating Channel| Wi-Fi 2.4GHz:

11: (Ch. 1-11) – United States(North America) 13: (Ch. 1-13) – Europe

14: (Ch. 1-14) – Japan

Antenna| PCB onboard antenna

Bluetooth Specification.

Pin Descriptions.

Pin Outline.

Pin Definition.

| Pin No.| Name| Type| Description| Voltage|
---|---|---|---|---|---|---
1| VCC| P| Supply 3.3V| 3.3V
2| P26| I/O| GPIO26/PWM5|
3| GND| P| Ground|
| 4| P7| I/O| GPIO7/PWM1|
---|---|---|---|---|---
5| RXI| I/O| UART_RX1/GPIO10|
6| P8| I/O| GPIO8/PWM2|
7| TX1| I/O| UART_TX1/GPIO11|
8| ADC| I/O| ADC/GPIO23|
9| P24| I/O| GPIO24/PWM4|
10| CEN| I/O| Module reset low effective|
11| P6| I/O| GPIO6/PWM0|

P :POWER
I: INPUT
O :OUTPUT

Dimensions.

Module Picture.

Module Mechanical Dimensions

Module Mechanical Dimensions

Antenna Information.

Antenna type.

This module antenna type is PCB on-board antenna with antenna gain of -1.3dBi (MAX )

Module layout considerations.
The UAM083-A0 module shall be welded to the PCB board. In order to obtain the best RF performance. Under the PCB on-board antenna, there should be no copper laying, device and wiring. During PCB design, the corresponding area should be cleared. As shown in the following figure.

Environmental Requirements.

Recommended Reflow Profile.

• Referred to IPC/JEDEC standard.
• Peak Temperature : <250°C
• Number of Times : ≤2 times

Note
Note: Take and use the module, please insure the electrostatic protective measures.

1. Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 ℃ for the MID motherboard. About the module packaging, storage and use of matters needing attention are as follows:
2.  The module of the reel and storage life of vacuum packing: 1). Shelf life: 8 months, storage environment conditions: temperature in: < 40 ℃, relative humidity: < 90% r.h.
3. The module vacuum packing once opened, time limit of the assembly:

Card

1. check the humidity display value should be less than 30% (in blue), such as: 30% ~ 40% (pink), or greater than 40% (red) the module have been moisture absorption.
2. factory environmental temperature humidity control: ≦ -30 ℃, ≦ 60% r.h..
3.  Once opened, the workshop the preservation of life for 168 hours.
4. Once opened, such as when not used up within 168 hours:
5. The module must be again to remove the module moisture absorption.
6.  The baking temperature: 125 ℃, 8 hours.
7.  After baking, put the right amount of desiccant to seal packages.

Humidity sensitive control.

Package

Packaging Detail.
The module and the humidity indicator card are placed together in vacuum anti- static packaging, separated by a certain amount of paper, and neatly placed in the packaging box.The packaging must have reliable moisture-proof and anti- collision measures.

Transport regulations

In the process of logistics or express transportation, attention should be paid to handling with care to avoid direct rain and snow.

 Disclaimer and copyright notice

All information in this document is provided according to the product status quo and subject to change without notice.
The contents of this document disclaim any warranties, including any warranties of fitness for sale, fitness for a particular purpose or non- infringement, and any warranties mentioned elsewhere in any proposal, specification or sample.

This document is not liable for any infringement of patent rights arising from the use of the information contained in this document.
This document does not grant any license, express or implied, to use any intellectual property rights, estoppel or otherwise.
All trademarks mentioned herein are the property of their respective owners.

Attention

Due to product version upgrade or other reasons, the content of this manual may be changed. Shenzhen Uascent Technology Co., Ltd. reserves the right to modify the content of this manual without any notice or prompt. If users need to obtain the latest product information, please apply for the final document with our company. This manual is only used as a guide. Shenzhen Uascent Technology Co., Ltd. tries its best to provide the latest information in this manual, but does not guarantee that the content of the manual is completely accurate.
None of the statements, information and recommendations contained in this manual constitute any warranty, express or implied.

FCC Statements
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority to operate the equipment.

Important Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Federal Communications Commission of the U.S. Government (FCC) and the Canadian Government authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator shall be responsible for re-evaluating the end-product

(including the transmitter) and obtaining a separate FCC authorization in the U.S. and Canada. OEM Integrators

End Product Labeling Considerations : This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: ” Contains, FCC ID: 2A68EJX-UAM083″. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.

OEM Integrators – End Product Manual provided to the End User : The OEM integrator shall not provide information to the end user regarding how to install or remove this RF module in end product user manual. The end user manual must include all required regulatory information and warnings as outlined in this document.

List of applicable FCC rules
The device compliance with FCC Part 15.247

Summarize the specific operational use conditions
The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required for the installed module

Limited module procedures Device is single module approval

Trace antenna designs
PCB onboard antenna, antenna gain is -1.3dBi the antenna size as below

RF exposure considerations
Compliance with FCC Part 2.1091
This device is intended only for OEM integrators under the following conditions: 1.The antenna must be installed such that 20 cm is maintained between the antenna and users. 2. The transmitter module may not be co-located with any other transmitter or antenna. As long as the two conditions above are met, additional transmitter testing will not be required.

Antennas
PCB onboard antenna, antenna gain is -1.3dBi.

Label and compliance information
The label compliance with FCC requirement and the end product must be labeled in a visible area with the following: ” Contains, FCC ID: 2A68EJX-UAM083″

Information on test modes and additional testing requirements
The module under Continuous transmit ion and lager than 98% duty cycle

Additional testing, Part 15 Subpart B disclaimer
The test results compliance with FCC Part 15B requirement.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>