ooni PA-A00598 Digital Temperature Hub Instruction Manual
- July 4, 2024
- Ooni
Table of Contents
Assembly translations
PA-A00598 Digital Temperature Hub
WARNING
Read the instructions before using the Digital Temperature Hub and retain them
for future reference.
Food probes and other accessible parts may be hot and sharp. Keep young
children away.
Only use the Digital Temperature Hub as instructed by this manual.
To avoid damage, only mount the Digital Temperature Hub and route the cables
in the locations instructed in this manual.
The food probes are suitable for use at temperatures of up to 842 °F (450 °C).
Do not use at temperatures exceeding this or on open flames.
Do not modify the Digital Temperature Hub.
CAUTION
Hand wash and dry the food probes before first use.
The food probes are not dishwasher safe.
Do not use chemicals or abrasive detergents to clean the food probes.
Risk of explosion if the battery is replaced by an incorrect type.
The Digital Temperature Hub works with Ooni Food Probes; other accessories may
be inaccurate, not work, or potentially cause damage.
Use the Digital Temperature Hub for accurate and immediate temperature
measurements in Celsius (°C) or Fahrenheit (°F). Connect the food probes to
get the perfect slow roast or seared steak, and connect to the Ooni app to
monitor all of this without having to touch your oven.
What’s in the box
a. Digital Temperature Hub
b. Mounting bracket
c. Thumb nut
d. Ambient temperature cable (x2)
e. Food probe (x2)
f. AA Batteries (x2)
g. Bracket screws
Buttons and inputs:
a. Power button
b. Temperature cycle button
c. Back-light button
d. Food probe input 1
e. Food probe input 2
f. Ambient temperature input A
g. Ambient temperature input B
h. Factory reset button
Screen
a. Main temperature display
b. Temperature ring
c. °C indicator
d. °F indicator
e. Left ambient Indicator
f. Right ambient Indicator
g. Food probe 1 Indicator
h. Food probe
1 display
i. Food probe 2 indicator
j. Food probe 2 display
k. Bluetooth status indicator
I. Low battery indicator
m. Eco mode indicator
Install batteries
Remove screws using a screwdriver and remove hatch. Insert 2 x AA batteries.
Replace hatch and secure screws.
If you are storing the oven for more than a month, remove the batteries.
Set up and assembly
4.1 | Attaching Digital Temperature Hub
a. Using 2x bracket screws, attach the mounting bracket to the underside of
the oven.
b. Attach the Digital Temperature Hub to the bracket using the thumb nut.
4.2 | Attaching the ambient temperature cables
a. Plug ambient temperature cable A into input A on the underside of the oven.
b. Plug the opposite end in to the corresponding input on the back of the
Digital Temperature Hub.
c. Repeat for ambient temperature cable input B.
4.3 |Securing the thermocouple cables
Use the clip on the underside of the oven to keep the cables neat and prevent
them from trailing.
Using the Digital Temperature Hub
5.1| Download the Ooni app
Setting up your Digital Temperature Hub is simple, and the Ooni app will walk
you through each step.
Scan this QR code to download or open the Ooni app. If you already have the
Ooni app, be sure to update to the latest version.
Scan to download the Ooni app.
5.2 | Powering On/Off device
a. Turn on the device with a short press of the power button.
b. Turn off the device with a long press on the power button.
Turn off your device when not in use to save battery.
The device will automatically switch off after 45 minutes.
5.3 | Activating Bluetooth pairing
Open the Ooni app.
Press the temperature cycle button for 3 seconds until the Bluetooth status
indicator starts flashing. Follow the instruction in the Ooni app to connect
your device.
A successful connection will cause the Bluetooth status indicator to stop
flashing and remain illuminated.
If the Bluetooth status indicator starts flashing quickly it means there is a
problem with the connection. Try restarting the pairing process if the problem
persists.
If a connection is not made, the Bluetooth will turn off after a short period
of time.
5.4 | Reading and cycling between ambient temperatures
Press the temperature cycle button to cycle between display options.
| This represents the average ambient temperature of your oven.
It is the recommended default setting.
---|---
| The ambient temperature of the left side of the oven is displayed
| The ambient temperature of the right side of the oven is displayed
5.5 | Read food probe
Check that the food probes are plugged into the correct inputs, and then the
temperatures will appear on the display.
When using the food probes, ensure they are inserted into the thickest part of
the meat, and make sure to avoid bones or fat.
The part of the food probe that goes into the meat should not be exposed to
temperatures above 480 °F (250 °C)
WARNING
Before and after use, clean the food probes with hot, soapy water, taking care
not to submerge the wire in the water, and dry immediately.
Take care when handling the Food Probes as they are sharp.
Always wear heat resistant gloves if handling the Food Probes when they are
hot.
Do not use the food probes at temperatures exceeding 842 °F (450 °C).
5.6 | Change unit of measurement
Use a short, single press of the power button to cycle between Celsius (c) and
Fahrenheit (F).
5.7 | Eco Mode
Use along press of the back-light button to cycle between full brightness and
Eco mode. When in Eco mode a short press of any button will fully illuminate
the display for a short period of time.
5.8 | Low battery warning
When the batteries are running out, the low battery warning will come on
indicating you should change batteries at next available opportunity.
WARNING
Always ensure the oven and temperature hub are fully cool before replacing the
batteries.
5.9 | High (Hi) or Low (Lo) Temperature
The Digital Temperature Hub is designed to read cooking temperatures between
-22 °F (-30 °C) and 999 °F (550 °C) and food probe temperatures between 0°C
(32°F) and 100°C (212°F).
If the temperatures are outside this range the relevant display will show
either Hi or Lo.
Care and maintenance
Digital Temperature Hub: Wipe down with a damp cloth and dry immediately.
Food probes: Before and after every use, clean with hot, soapy water, taking
care not to submerge the wire in the water and dry immediately. Not dishwasher
safe.
Store your Digital Temperature Hub inside and for extended periods without
use; remove the battery to prolong battery life and prevent damage.
Never submerge the Digital Temperature Hub, food probes or wiring in water.
Troubleshooting
Issue| Possible Cause|
Solution
---|---|---
Ambient temperature / food probe temperature is not showing on the display|
1. The connection could be dirty.
2. The ambient temperature cable is not plugged into the oven.
3. The probes / sensor may be connected to the wrong input.
4. The probe may be damaged.| 1. Remove the probe / sensor from the Digital
Temperature Hub and from the oven. Gently clean with a damp cloth. Allow to
fully dry and re-insert into the device.
2. Check the ambient temperature cable is plugged into the correct port on
the oven. Try removing and re-installing even if it is.
3. Check you have the correct ambient sensor and food probe plugged into the
correct input.
4. Try plugging the probe into the other input, if it works there may be a
problem with the device, if it doesn’t there may be a problem with probe.
Contact Ooni support.
Ambient temperature sensor readings aren’t accurate.| 1. The probes may be
connected to the wrong input.
2. The average or opposite ambient temperature is being displayed.
3. The sensor in the oven could be dirty.
4. The calibration settings of the device have been changed.| 1. Check you
have the correct ambient sensor plugged into the correct input.
2. Cycle through the individual temperature readings to ensure the desired
reading is being displayed.
3. Ensuring the oven is completely cold, carefully reach inside and gently
clean the temperature sensor with a damp cloth.
4. Use the factory reset button to return the device to its original
calibration.
Display is faint or won’t turn on at all.| 1. The battery is nearly or is
already flat.
2. The Digital Temperature Hub is in Eco mode.| 1. Ensuring the oven is
completely cold follow the steps outlined in this manual to replace the
batteries.
2. A long press of the back-light button will return the product to full
brightness.
Ambient temperature reading is high but my food isn’t cooking properly.| Stone
may not be warm enough. The stone will take longer to preheat than the oven’s
ambient temperature.| Give your stone more time to preheat.
Use an Ooni Digital Infrared Thermometer to get an accurate reading of stone
temperature.
My Digital Temperature Hub will not connect to my device.| 1. Your device was
not one of the most recent connections.
2. Too far away for the device.
3. Unknown reason.| 1. Follow the Bluetooth pairing steps to reconnect your
device.
2. Ensure you are within 10m (33ft) of the device with a clear line of sight.
3. Try using the factory reset button to remove all existing Bluetooth
connections then follow the steps to start again.
I have a problem that isn’t listed here.| I’ve discovered a new problem!|
Contact support.00ni.com
This marking indicates that this product should not be disposed of with other
household wastes throughout the EU and UK. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact the
retailer where this product was purchased. They can take this product for
environmentally safe recycling.
You must have a live internet connection in order for the Ooni app to work.
We recommend you update to the latest version of iOS and Android to operate
the Ooni app.
Your mobile device must have Bluetooth wireless technology 4.0 support
(Bluetooth® wireless technology Low Energy) in order to set up a connection
with the appliance. Check your device specification for compatibility.
— BLE 2.4GHz
— 2.4GHz, 25mwW
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Ooni Limited is under
license.
Other trademarks and trade names are those of their respective owners.
All references to “Ooni” in this manual include Ooni Limited and its relevant
subsidiaries and holding companies as defined in section 1159 of the Companies
Act 2006.
OONI DOES NOT ACCEPT ANY RESPONSIBILITY, LEGAL OR OTHERWISE, FOR THE
INCIDENTAL OR CONSEQUENTIAL DAMAGE TO PROPERTY OR PERSONS RESULTING FROM THE
USE OF YOUR OONI OVEN WHICH DOES/D\D NOT COMPLY WITH ANY OF THE PROVISIONS OF
THIS MANUAL.
OONI SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR
OTHER DAMAGES OF ANY NATURE WHATSOEVER IN EXCESS OF THE ORIGINAL PURCHASE
PRICE OF YOUR OONI OVEN.
Some states or countries do not allow the exclusion or limitation of
incidental or consequential damages, therefore such limitations or exclusions
may not apply to you.
Product Name: Digital Temperature Hub.
Model: UU-C00182
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC & IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Digital
Temperature Hub
Manualhttps://ter.li/Ooni_KodaG2_24
ooni.com
©2024 Ooni
Ooni is a registered trademark of Ooni Ltd.
All rights reserved.
PA-A00598
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>