Audionic TWS AirBass Signature True Wireless Earbuds User Manual
- July 3, 2024
- Audionic
Table of Contents
Audionic TWS AirBass Signature True Wireless Earbuds
Product Information
Specifications
- Product Model: TWS
- Bluetooth Version: 5.3
- Rated Input: 5V-200mAh
- Case Battery: 30mAh*2
- Charging Case Capacity: 200mAh
Product Usage Instructions
Pairing Instructions
- Make sure the Bluetooth device you want to pair with is in pairing mode.
- Open the charging case of the TWS earbuds.
- The earbuds will enter pairing mode automatically. Look for “TWS” on your device’s Bluetooth list and select it to pair
- Once paired successfully, you will hear a notification sound confirming the connection.
Safety Instructions
Note: FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 5mm between the radiator and your body.
FAQ
-
Q: How do I know when the earbuds are fully charged?
A: The LED indicator on the charging case will turn solid green when the earbuds are fully charged. -
Q: Can I use only one earbud at a time?
A: Yes, you can use either the left or right earbud independently for mono audio playback.
USER MANUAL
- Product Model: TWS
- Bluetooth version: 5.3
- Rated input: 5V-200Mah
- Case Battery: 30Mah*2
- Charging case: 200mah
Basic function operation
- Turn on: Take out the charging case of the earphone and turn on automatically
- Shutdown: Put in the charging case and close cover to shut down,
- Play and pause music: Press 1 time
- Add and subtract volume: press 3 times continuously
- Previous/Next: Press twice times
- To answer a call: Press during an incoming call 1 Press any earphone Call status: During a Bluetooth call, the main and secondary phones turn off their lights
- Hang up: Press any button one time
- Reject the call: Hold down any earphone in an incoming call state for 1.5 seconds
- Low power alert: When the battery voltage is lower than 3.4V, the low power alert is reported (once every 60 seconds)
- Shutdown voltage: The battery voltage is lower than 3.2V
- Charging completed: “4.2V full charge, automatic shutdown after full charge”
- Hibernated: The device is not connected after the pair connection and shuts down after 3 minutes
- IPHONE battery display: The Bluetooth connection is successful, and the iPhone no battery icon is displayed. (Playing status)
- IPHONE Volume sync: The Bluetooth connection is successful, and the machine volume is synchronized with the phone volume. (Playing status)
- Automatic back connection: After the earphone is turned on again, the Bluetooth automatically reconnects the phone.
- Remote disconnect automatic back connection: remote disconnect, back to 10 meters Bluetooth automatic connection to the phone
- Charging automatic shutdown: playing state, hibernation, standby, earbuds into the warehouse will shut down
Pairing instructions
The first time to use Bluetooth earphone need to let the left and right ears
pair.
Pairing method: open the upper cover of the left and right earphones and take
out the charging compartment of the left and right ears will flash the power
light once), wait 8-10 seconds, open the Bluetooth phone to find the
corresponding Bluetooth name click the link (when there is a unilateral
connection, or two main ears, you need to cancel the connected earphones and
mobile phones. Put the left and right ears into the charging bin at the same
time, switch the machine again, and then use the mobile phone to connect after
pairing.)
Note
- The first time to receive the goods plug in the data cable charging, until fully charged after use, you can make the Bluetooth earphone longer life.
- Do not use the super fast charge of 2A and above current, so as not to damage the circuit chip with too much current.
FCC
Labeling requirements
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Information to user
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>