CoolBe E13 Smart Glasses User Manual
- July 3, 2024
- CoolBe
Table of Contents
CoolBe E13 Smart Glasses
Product Information
Specifications
- Compliance: FCC Part 15
- RF Exposure: Meets general RF exposure requirement
- Usage: Portable exposure condition without restriction
Product Usage Instructions
Safety Precautions
Before using the device, please read the safety precautions in the user
manual to ensure safe operation.
Powering On the Device
- Press and hold the power button for 3 seconds to turn on the device.
- The device will indicate when it is powered on and ready for use.
Using the Device
- Follow the user manual for specific instructions on how to operate the device.
- Ensure the device is within the recommended RF exposure range for optimal performance.
Cleaning and Maintenance
Regularly clean the device using a soft, dry cloth to prevent dust buildup
and maintain functionality.
Storage
Store the device in a cool, dry place away from direct sunlight and
moisture to prolong its lifespan.
Frequently Asked Questions (FAQ)
-
Q: What should I do if the device stops working suddenly?
A: Check the power source and connections. If the issue persists, contact customer support for assistance. -
Q: Can the device be used in all weather conditions?
A: The device is designed for portable exposure conditions without restriction, but avoid exposing it to extreme weather conditions.
Switch machine
Power on: Press and hold the red line on both sides for 5 seconds to
power on
Shutdown: Long press the red line on both sides for 5 seconds to shut
down
(Note: If there is sweat on the glasses, it will affect the switching
effect, please pay attention to clean it)
Paired temples
After the boot two miror legs automatically paired
Pairing
After the smart glasses are turned on, turn on the Bluetooth of the mobile
phone, search for the device name E13 and connect.
(Note: The smart glasses will automatically turn off when charging, and
automatically turn on when the charger is unplugged or fully charged. It will
automatically recognize the paired device and connect automatically.)
Phone
Incoming call answer/end call: touch (left or right) 1 times
Reject a call: long press the touch key (left or right) for 2 seconds
(Note: the volume of the call can be adjusted on the phone)
Music
Music pause/play: touch (left or right) 1 times
Music switch: touch and click left 2 down to switch to the previous song
Touch and click right 2 down to switch to the next song
Remote camera
Remote control photo: First open the camera on the mobile phone, then touch the glasses (left or right) button twice to take a remote photo
Voice assistance
Turn on voice assistant: Long touch the red lines on both sides for 2
seconds (left or right)
Turn off voice assistant: touch and tap (left or right) 1 time
Chinese and English switching
Chinese and English switching: touch (left or right) 4 times
Recharge
Magnetic charging: the red light is always on when charging
The blue light a minute turns off after a minute on when fully charged (it
takes 90 minutes to fully charge)
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>