IDEAL 5255 Stack Cutter Instruction Manual

: July 2, 2024
: IDEAL

Table of Contents

5255 Stack Cutter
Specifications
Product Usage Instructions
Safety Precautions
Installation
Startup
Operation
Blade and Cutting Stick Replacement
Maintenance and Cleaning

5255 Stack Cutter

“`html

Specifications

Model: IDEAL 4855-6655
Operating Instructions: EN
Power Requirements: 230V / 10A min, 115V / 15A min
Designed for cutting stacks of paper to a specified size
One-man operation only

Product Usage Instructions

Safety Precautions

Before operating the Guillotine, ensure to read and understand
the safety precautions provided in the operating manual.

Installation

1. Ensure the power cord is connected to a single-phase socket
matching the power requirements.

2. Protect the mains cable against heat, oil, and sharp
edges.

Startup

1. Disconnect the Guillotine from the mains before starting any
service work or panel removal.

2. Ensure the blade is covered by the pressing bar before
clamping.

Operation

1. Use the safety two-handed control system for pre-clamping and
cutting.

2. Follow the instructions on setting the backgauge using the
hand-wheel.

Blade and Cutting Stick Replacement

1. Blade and cutting stick replacement should only be performed
when the main switch is switched off.

2. Make sure all safety guards are in place before starting any
replacement procedures.

Maintenance and Cleaning

1. Regularly clean the Guillotine to ensure smooth
operation.

2. Perform annual inspections and safety tests as outlined in
the manual.

FAQ

Q: Can children operate the Guillotine?

A: No, children must not operate the machine.

Q: What materials should not be cut using the Guillotine?

A: Do not cut hard materials or materials that may splinter.

“`

Guillotines
IDEAL 4855

EN Operating Instructions
IDEAL 5255

IDEAL 6655

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm

Table of Contents

Safety precautions

3

Intended use

4

Operating elements

5

Installation

10

Startup

12

Operation

15

Blade and cutting stick replacement

26

Maintenance and cleaning

35

Annual inspection / Safety test

36

Possible malfunctions

37

Accessories

42

Technical data

43

EC-declaration of conformity

46

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 2

Safety precautions Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available.
Children must not operate the machine!
Do not reach beneath the blade!
Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 29 and 31).
Danger! Risk of injury!
Do not cut hard materials or materials which may splinter!
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 3

Safety precautions / Intended use

Do not use any spray cans with flammable content near to the cutting machine!

Do not use any flammable cleaning agents.

Intended use
The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for “one-man operation” only!
Warning! Clips or similar damage the cutting blade.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 4

Safety precautions / Operating elements
8 7 8
3
9 1 6 4 5 2 1

Operating elements
A Safety two-handed control system
Pre-clamping and cutting
B Overload switch (blade drive/clamp drive/
backgauge drive)
C Backgauge control D Main switch E Hand-wheel for backgauge setting F Key switch G Backgauge H Side lay left and right I Front safety guard
Disconnect from the mains before starting any service work or before removing the panels!

Replacement of blade and cutting stick may be performed only when the main switch is switched off!
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 5

Safety precautions
A

All components which could endanger the operator are covered by a guard!

A B

A
Operating the machine without safety device is forbidden! (Front safety guard (A), rear screwed safety guard (B) and panel (C).

C

A

C

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 6

Safety precautions

The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B)

A B

Before working with the machine and after

every blade replacement the automatic cut-off

function of safety guard (A),(correct if distance

between cover and table is < 20 mm) main

switch (B) and control panel (C) must be

A

checked.

C B

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 7

Safety precautions
230V / 10A min 115V / 15A min

Connect the power cord to a single phase socket.

Ensure free access to mains!

When not in use for a longer period switch off. (Main switch to “0”).
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 8

Safety precautions

Protect mains cable against heat, oil and sharp edges!

Danger! Blade must always be covered by the pressing bar.

Clamping

OK
Blade

OK
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 9

Installation

Remove the stand from the wooden pallet.

4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set (C).

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 10

Installation

Tools can be kept in the holder provided.

Cutting sticks (A) can be put in the tool holder.
A

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 11

Installation / Startup

Side tables (A), left and right are available as an option (No. 9000 528).
A

Startup
Plug into socket. The machine must be connected directly to the socket.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 12

Startup
A
A

It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use. · All covers have to be mounted (A). · The release for cutting is allowed only if
the cover is closed and the two-hand safety device is operated at the same time (B) · If the front cover closes by itself the gas spring (X) needs replacing.

We recommend you keep a record of your

A

test results.

A B

X
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 13

Startup
C

Position the main switch to “I” (A). Insert the

key for the control system and move it to the

right (B). Open the safety guard (C). The

D

machine is now ready for use.

S Press button (D).
Machine will automatically go to the start position.

B A

The measurement is set either with the handwheel (A) or by programming (B) the cutting measurements. Measurement is shown on the display in inches or cm (B).
B
A
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 14

Operation
A

Cut is indicated by means of an optical light beam (A). The blade cuts at the front edge of the light beam. Please only use this if an exact measurement is not required.

B A
B

The stack of paper can be placed against the back gauge (A) and the left or right side stop (B). Use the supplied paper knock-up block (C) to move the stack of paper.

C

Note: Place the stack of paper against the

back gauge using the paper knock-up

block before each cut.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 15

Operation
A

The clamp moves automatically when cutting is activated. The paper can also be pressed in advance. Clamping and cutting is activated by the actuators (A) on the front table.
The actuator has 2 switching steps: 1. pre-clamping 2. automatic clamping and cutting

Switch position 1

Switch position 2

= Pre-clamping
Press down both actuators to step 1
= Clamp returns
Press down completely one of the actuators
= Cutting sequence with automatic clamping
Press down both actuators to step 2

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 16

Operation

Close the safety guard.

Cutting activation: Press both actuators of the two-handed control system (A) simultaneously and keep pressed until the paper is completely cut.
A
To interrupt or stop cutting: To interrupt or stop cutting, release both actuators (A) of the two-handed control.
A
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 17

Operation
L

Start machine
D F · Main switch to position “I”, insert the key
for the control panel and turn to the right. Start screen appears The following functions are changeable: Brightness CM/INCH Touchtone ON/OFF Language

J G · Press START backgauge moves to the

rear and searches for the reference position,

wait until a measurement
C is shown in the display

4855 = 45.00 cm, 17.717 inches

5255 = 52.00 cm, 20.472 inches

6655 = 61.00 cm, 24.016 inches

· The DIN and free programmable

measurements are recallable with the

C

W respective buttons .
Memory 1: A2, A3, A4, A5,

K

Memory 2: A6, A7, B3, B4

Memory 3:

Memory 4:

W

and in inch Memory 1: 4¼”, 5 ½”, 7″, 8 ½”

Memory 2: 11″, 12″, 14″, 17″

Memory 3:

Memory 4:

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 18

Operation
L

In memory 3 + 4 (mm and inch) no

measurements are saved. Until a first input

of data the following will be shown in the

C

corresponding fields:

K

The measurements entered remain stored. They cannot be deleted but overwritten.

How to program Memory 3 and 4

W

W Press the memory button to enter the

memory platform (3 or 4). Enter the required

measurements or overwrite them. Press the

button and keep it pressed until

an acoustic signal sounds, the

measurements have been saved now.

Warning! Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) see above is stored. For information on how to store see picture
K below left. Is shown on the screen see .

A B After 30 minutes the machine ( ) switches
to energy-saving mode. The machine is reactivated by touching the
L keypad area .

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 19

Operation 8
7 8
L

10
3 9 1 6 4 5 2 1
M

Cutting activation Warning!
· Run backgauge to the front for turning the paper stack
· Do not interrupt the upward movement of the blade by performing switching procedures
· Wait until the display is green before activating a cut
· Blade must always be at the top and be covered by the clamp. Do not touch the blade (see safety information on page 34). Risk of injury!
Cutting to specified dimensions · Press MAN.
L · Enter dimension on the numerical key pad
Measurement is shown in red (If a wrong dimension is entered this can be
corrected by pressing the Y button)
M · Press START dimension is approached,
Measurement is shown in green · Insert paper and move by means of the
J G stacking angle to the backgauge and H side lay on the left I · Close the safety guard .
· Release the cut.
Cut according to markings Press MAN.
E · Adjust the backgauge with the hand-wheel
to the back · Insert paper and move by means of the
I G stacking angle to the backgauge and side H lay on the left E · Turn the hand-wheel to the right until the
marking on the paper to be cut is below the cutting line indicator
E · The further the hand-wheel
is turned to the right, the quicker the backgauge moves. If the hand-wheel is turned to the left the backgauge will return quicker.
I · Close the safety guard .
· Release the cut.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 20

Operation
P L
Z

N M O
X

Eject function
N M If EJECT is pressed instead of START , L after inserting the measurement , the
backgauge will advance forwards so that paper can be removed. Finally the backgauge moves to the last setting.

Multiple cut
L · Enter the start dimension on the display

· Advance to the measurement with the
M START

G · Push the paper to the backgauge

· Press multiple cut

O

· Multiple cut sign appears top left together with
P the value 00.00

· Enter multiple cut measurement (appears in

red letters)

· Press START the backgauge advances by

the multiple cut size

· This is repeated everytime a cut is activated.

Exiting program-mode

· Press multiple cut

O (yellow).

Multiple cut sign and value are deleted.

Calculator function
X · Press CALC , calculate the desired Y measurement, e.g. 40 – 2 = and
the backgauge advances immediately to 38.
Z · With the key < can be changed to
manual mode MAN. at any time.

Y

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 21

Operation

Programming

Q R

This control system enables you to store 99 programs with 99 programmable steps. One step represents one measurement. After

entering the program numbers you are able to

cbhuattnognejbetawnedebn s.everal program steps with the

Q First figure on display = program number.

R Second figure on display = program step.

Smallest cutting measurement

4855 3.50 cm / 1.378 inch

5255 3.50 cm / 1.378 inch

6655 2.50 cm / 0.984 inch

Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off.

Entering a program · Press EDIT “Load program no.”
appears · Enter program number 01 … 99, with
Q (Top number on display = program
number) · If measurement is shown on the display the
program is reserved, select another program
R · Program step “01 Step” 00.00 appears. R (Second figure on display = program step.
· Enter dimension, or move the backgauge to the desired measurement with the
E hand-wheel
· Store the measurement ,next program step appears.
· Enter the next measurement and with Enter store the measurement etc.
· Should the entered program be required immediately press RUN
· Press Enter · Press START · Escape the program mode press MAN.

Cancel a program · Press EDIT · Scroll with PRG until “Delete program no.”
appears · Enter Program number · Press Enter · Press Enter .

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 22

Operation
Z

Calculator function in programming

· Press EDIT

a

· Enter program number

· Enter the 1st program step e.g. start-up

measurement 40 cm

· Store the measurement with enter

X · Press CALC , calculate the desired

Y measurement e.g. 40 – 2 = , the

a calculated measurement 38 flashes.

· Pressing the Enter-key again, the

calculated measurement is saved in the

corresponding step.

· With the key < it can be changed to

programming EDIT at any time.

X

Y

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 23

Operation

Adapting a program when the printer’s

imprint deviates

· Press RUN “Load program no.”

appears

· Enter program number 01 … 99, and with

2 x Enter proceed to Step 1

· Correct the cutting position of the backgauge

with the hand-wheel

· MODIFY V appears on the screen and the

measurement flashes

· To store press MODIFY

· Release a cut and turn the paper

· If the printer’s imprint deviates it can be

corrected during the first two cuts via the

hand-wheel see above

· Correction is only possible during the first

two cuts

V

· After leaving the RUN mode the original data is stored again.

Delete a step · Press EDIT · Enter program number, confirm with Enter
· bSeleacntdpjrogram step with the arrow keys
· Scroll with STEP until “Delete step no.” appears, Press 2 x Enter .

Insert a step

· Press EDIT

· Select a program, confirm with Enter

· Scroll with STEP until “Insert step no.”

appears

· Enter insert position e.g. 02

· Confirm with Enter

· Enter a measurement

· Store the measurement with

·

The cutting position can be screen with the arrow keys

sbhowanndojn t.he

Changing a program step · Press EDIT · Select a program, confirm with Enter · Scroll with STEP until “Load step no.”
appears · Enter step position e.g. 03 · Confirm with Enter · Enter a new measurement, Store the
measurement with .

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 24

Operation

Eject function program

Q R

S

· If a short measurement e.g. 30 cm and then a long measurement e.g. 40 cm is cut at the

start of a program then it is wise to insert an

S EJECT after the first cut so that the paper

is pushed to the front.

· The EJECT function can be added each time

N

a measurement is entered and ejects before advancing to the next measurement. When

S the eject function is programmed an “E”

appears top right in the display.

· Inserting an Eject function subsequently in

the program. Select a program and advance

tbo thaendstjep

to be changed Enter the new

with the arrow measurement

keys and

before activating the enter button press
N EJECT .

Example of a program eject function

· Press EDIT

T

· Enter program number e.g. 08 · Press Enter

· 1. Enter program Step e.g. 30 cm

U

· Press Enter

· 2. Enter program Step e.g. 40 cm

Press EJECT and with Enter store the

dimension.

How the example works

· Press RUN

· Enter program number 08

· Press Enter ,

· Press START , Measurement is approached

· Insert paper

· Release cut 1

· Eject (Ejection is completed, turn the paper)

O

· The backgauge moves to program step 2

· Release cut 2

Multiple cut program

· Press EDIT

· Enter program number

· Enter the 1. program step e.g. start-up

measurement 40 cm

· Store the measurement with Enter

· Press the multiple cut symbol

O

T · Enter the number of cuts with the + button

U (max. 15 cuts) followed by the multiple cut

size (cutting width).

· Store with Enter .

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 25

Blade and cutting stick replacement

If the cutting quality decreases: · Check the cutting depth (see page 34). · Check the cutting stick (see page 30). · Replace or grind the blade (see page 26 – 34).
The blade cannot be ground if the blade height is less than 83 mm / 3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen.
Danger! Risk of injury! The blade is extremely sharp. Do not extract or transport the blade without protection. Changing the blade may only be performed by trained staff.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 26

Blade and cutting stick replacement

Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set (A)) or tool holder (B).

1. 2.

Close the safety guard (1.). Lower the blade by pressing both cutting actuators (2.). Keep one actuator pressed and turn off the main switch (3.).

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 27

Blade and cutting stick replacement
C A

The 3 eccentrics are now exposed and should be turned counter clockwise to position “0” with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position “0” (B).
Only 4855 Unscrew the blade screws (C) on the right hand side.

B

Remove the special wrench. Close the safety guard, and turn on the main switch until the blade returns to the home position.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 28

Blade and cutting stick replacement Position the main switch to “0” (1.) Remove the 2 blade screws on the elongated
A holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.).
3.
2.

Remove 2 blade screws (1.) 4855 and 3 blade screws (1.)

5255, 6655.

Loosen the grips (2.) of the blade changing

tool (A) lightly and allow the blade to be taken

downwards out of the machine (3.). Place the

blade into the blade carrier (B) and screw it

into place (4).

A

2. B 4.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 29

Blade and cutting stick replacement

Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).

Replacing the cutting stick (not the blade). · Turn the blade adjusting screw (A) to the left
until it stops. (Otherwise the first cut will be too deep). · Remove the cutting stick according to top picure. · Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt.
Danger! Risk of injury!
Cutting test after replacing the cutting stick (not the blade) · Insert the paper and release the cut. · If the last sheet of paper is not cut along the
entire length turn the blade adjusting screw (A) ¼ turn to the right. · If the last sheet is still not completely cut repeat this process until the last sheet is cut along the entire length.
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 30

Blade and cutting stick replacement
A

Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A). · Make sure there is a space ot 11 mm or
0.43 inches! (B). · Blade must be covered! (C).
Danger! Risk of injury!

11 mm 0.43 inch
B B C
C
Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).
A 1.
2.
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 31

Blade and cutting stick replacement

B

A

Lightly tighten 3 (4855 has 2) of the 5 blade screws (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws (3.). Return blade changing tool to tool holder (B).
Only 4855 Lightly screw in the right blade screw (A) when the blade is lowered.

Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position “I” (2.).

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 32

Blade and cutting stick replacement

Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.).

33..

4. A

Open the safety guard (4.). With the special wrench (B) the 3 eccentrics should be screwed down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).

A
2.

Turn main switch to position “I” (1.). Blade will return to upper position. Tighten the blade screws (2.) firmly.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 33

Blade and cutting stick replacement
A

Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
Danger by blade replacement! Blade must always be covered by the pressing bar (see picture below at the left).

Clamping

OK
Blade

OK
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 34

Maintenance and cleaning
D

Danger! Disconnect the mains before starting any service work or before removing the cover. Maintenance work may only be performed by trained staff.
Grease the backgauge (A) control weekly with a grease gun (use special grease for cutting machines). Advance the backgauge as far as possible to the front. Grease the remaining parts twice a year (see picture). The main switch must be on “0” (B). Remove lower panel (C). Tools in tool set or tool holder. · Remove any paper. · Grease the machine. · Check the 4 joining bolts and 2 pushing bars
for wear (D). If necessary inform your service personnel. · Mount the machine. With more than 5 hours of use per day, the service must be performed more often.

/

= Greasing points

on the machine.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 35

No. 9000 625 No. 9800 933 No. 9001 828

Maintenance and cleaning
Next Maintenance
2025
Krug & Priester GmbH & Co. KG 72336 Balingen – Germany Parts & Service HOTLINE Germany: +49 7433 2690 France: +33 3 8820 5435 North America: +1 843 552 2700 All other countries: Please contact your local distributor www.krug- priester.com
2029

Annual inspection To maintain the operational safety and to prevent premature wear, we recommend an annual inspection and maintenance of the machine by a qualified service technician.
Safety test The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 36

Possible malfunctions

Machine does not function!

Is the machine plugged in?

Main switch to position “I”? (A) Control system activated? (B) (Turn key to the right) Release a cut see page 17.
B A
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 37

Possible malfunctions

Cut cannot be made. · If cover is open:
close it. · If cover is closed:
open and re-close it. (Security check).

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 38

Possible malfunctions

Machine turns off: · Machine overloaded.
Safety button (A) or (B) ejects. (Allow 1 minute cooling time and reset the safety button (A) or (B).

· Machine blocked. · Blade is blunt.
Eliminate the cause, and push the safety button (A).

A,B,C

· Backgauge blocked Safety button (C) ejects. Eliminate the cause, and push the safety button (C).

Safety button for: A = Blade drive B = Clamping drive C = Backgauge drive

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 39

Possible malfunctions
A

Does not cut through the last sheet: · Turn or turn around the cutting stick (A),
readjust the blade by means of the blade adjusting knob (B) (see page 34).
Poor cutting quality or blade stays in the paper stack. · Change the blade (C) (see pages 26 – 34).

B

C
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 40

Possible malfunctions
A B
C
Service

Display illumination off · Machine is plugged in? (A) · Main switch on position “I”? (B) · Push in the safety button! (C) · Check the units fuse and the on-site circuit
breaker! After 30 minutes the screen switches to energy-saving mode The screen is reactivated by touching the
L keypad area .
Motor runs but blade does not move downwards. · Security brake has been activated!
Inform the Service Team! Did none of the specified solutions help you with your problem? Contact: Service
· www.krug-priester.com · service@krug-priester.com

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 41

Accessories

Recommended accessories:

Blade · No. 9000 021 · No. 9000 130 · No. 9000 025 HSS – Blade · No. 9000 126 · No. 9000 131 · No. 9000 135

4855 5255 6655
4855 5255 6655

Cutting stick (6 pieces) · No. 9000 022 4855 (red) · No. 9000 303 4855 (grey) · No. 9000 024 5255 (red) · No. 9000 305 5255 (grey) · No. 9000 026 6655 (red) · No. 9000 306 6655 (grey)

Blade changing tool 1 · No. 9000 523 4855 · No. 9000 524 5255 · No. 9000 526 6655

Grease tube 1 · No. 9000 625

Grease cartridge · No. 9800 933

Brush · No. 9001 828

Paper knock-up block 1 · No. 9000 521

Side tables left and right · No. 9000 528

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 42

1 Included in delivery

Technical data
A
4855 5255 6655

Technical data: · Power supply: 230V/50Hz/1~,
120V/60Hz/1~ · Cutting height: 80 mm · Leakage current < 3,5mA · Power cord gauge min. 1,5mm2 (230V) · Power cord gauge AWG 12 (20A) (120V)
The exact technical specifications can be found on the technical specifications sticker (A) on the machine. A wiring diagram is found in the electrical switch box. To claim under guarantee, the machine must still carry its original identification label.

Cuttinglength
mm
475 520 650

Tabledepth mm
450 520 610

Minimum space requirement Weight

(W X D X H) mm

kg

762* x 992 x 1296 860* x 1120* x 1293 992 x 1220 x 1293

228 252 302***

with side tables: (Width) 4855 1349 mm
** with side tables: (Depth) 4855 992 mm
with side tables: (Width) 5255 1436 mm
** with side tables: (Depth) 5255 1120 mm
with side tables: (Width) 6655 1565 mm
with side tables: (Depth) 6655 1220 mm
** with side tables: 4855 237 Kg with side tables: 5255 261 Kg *** with side tables: 6655 311 Kg

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 43

Technical data

This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and 2014/30/EG.
Sound level information: Sound measurement to EN 13023 : 72,5 db (A)
Subject to alteration without notice.

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 44

Technical data

The company Krug + Priester has the following certifications: · Quality management system according to
DIN EN ISO 9001 · Environmental management system
according to DIN EN ISO 14001 · Energy management system according to
DIN EN ISO 50001

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 45

EC-declaration of conformity

– Herewith we declare that

4855 5255 6655

GS-ID No. 11485501 11525501 11665501

UL-ID No. 10485002 10522102 10655002

– complies with the following provisons applying to it

2006/42/EG: EC Machinery directive

2014/30/EG: EMV Electromagnetic compatibility directive

2011/65/EU, 2015/863/EU RoHS directive

– Applied harmonised standards in particular

EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN ISO 12100; EN 61496-1; EN 61496-2; EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1; BS EN 60204-1; BS EN 1010-1; BS EN 1010-3; BS EN 55014-1; BS EN 55014-2; BS EN 61000-3-2; BS EN 61000-3-3; BS EN ISO 12100; BS EN ISO 13857; BS EN ISO 11204; BS EN 13023; BS EN ISO 13849-1

11.02.2022 Date

Authorized representative for technical documentation
Krug & Priester GmbH & Co. KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany)

Daniel Priester – Managing Director –

IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 46

Remarks: IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm 47

Made in Germany
Krug & Priester GmbH & Co. KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany) www.krug-priester.com
IDEAL 4855-6655 EN 9700214 9700157 08-2022 20240405zm