AXXESS AXDIS-BW122 Interface System BMW M.O.S.T. 25 Amplifier Instruction Manual
- July 8, 2024
- AXXESS
Table of Contents
AXDIS-BW122
Installation Instructions
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications.
Interface Components
- AXDIS-BW122 interface
- BLK-AXDIS-BW122 B harness
Applications
US Applications
BMW
1 Series (E82, E87, E88) …………………………..2008-2013
3 Series (E90, E91, E92, E93)……………………2006-2012
5 Series (E60, E61) …………………………………2004-2010
X6 (E71)…………………………………………………2008-2014
World Applications
BMW
1 Series (E82, E87, E88) …………………………..2008-2013
3 Series (E90, E91, E92, E93)……………………2006-2012
5 Series (E60, E61)………………………………….2004-2010
X6 (E71)…………………………………………………2008-2014
BMW (with MOST 25 amplifier)
Interface System 2004-2014
Interface Features
- Designed for MOST* 25 amplified systems
- Provides accessory power (12 volt)
- Retains audio controls on the steering wheel controls
- Easy to set Dipswitches for SWC configuration
- Provides NAV outputs (parking brake, reverse, and speed sense)
- Micro-B USB updatable
Note: Warning and parking sensor chimes are not retained Backup Camera not retained if equipped.
- Media Oriented System Transport
Tools & Installation Accessories Required
- Crimping tool and connectors, or solder gun, solder, and heat shrink
- Tape
- Wire cutter
- Zip ties
ATTENTION : With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.
CONNECTIONS: BLK-AXDIS-BW122 B HARNESS
SWC CHART
Installing the AXDIS-BW122 Interface
With the key in the off position:
- Connect male 3.5mm jack to the steering wheel control port on the radio.
- Ensure that the dipswitches are set to the desired radio type. Refer to SWC Chart next page.
- Connect the AXDIS-BW122 harness to the AXDIS-BW122 interface.
- Remove the dust cover from the optic port on the AXDIS-BW122 interface.
- Connect the factory fiber optic cable to the AXDIS-BW122 interface.
- Connect the AXDIS-BW122 harness to the wiring harness in the vehicle.
- Turn on the ignition and test all features.
NOTE : For Dipswitch Settings for your Radio Type, refer to SWC Chart on page 3.
Installing the Fiber Optic Cable
Removal of the original fiber optic connection is required to adapt to the Media Oriented System Transport (MOST) interface.
- Seat the AXDIS-BW122 amplifier interface in the black connector housing provided with this kit and snap the housing in place. (Figure A)
- From the original Fiber Optic Connector: Using a pick tool, carefully pull this tab towards the outside edge for the connector housing. Gently remove the fiber optic insert from the connector. (Figure B)
- From the MOST Interface : Push the tab toward the gray dust cover and, using a needle nose plier, remove the gray dust cover. Replace the gray connector with the factory fiber optic cables into the MOST interface’s black connector housing. (Figure C)
Having difficulties? We’re here to help.
Contact our Tech Support line at: 386-257-1187
Or via email at: techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 5:00 PM
Sunday: 10:00 AM – 4:00 PM
AxxessInterfaces.com
© COPYRIGHT 2024 METRA ELECTRONICS CORPORATION
REV. 4/8/24 INSTAXDIS-BW122
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>