Riviera Commercial Aluminum Horizontal Blinds Instruction Manual

Riviera Commercial Aluminum Horizontal Blinds

IMPORTANT INFORMATION

With attractive design and resilient construction with good value, Aluminum Horizontal Blinds are available in manual cordless options, ideal for larger- size commercial projects.

Color Options

• 110 Snow Gloss

• 116 Polar Bear*

• 885 Chalk White*

• 990 White*

• 125 Pure White

• 1392 Quartz

• 113 White Cap

• 385 Evening Snow

• 974 Pearl*

• 991 Matte Alabaster

• 002 Alabaster*

• 973 Antique*

• 148 Vanilla*

• 830 Canvas*

• 310 Sand*

• 316 Malibu Sand

• 992 Matte Mushroom

• 365 Mushroom*

• 186 Beige

• 384 Rich Earth*

• 994 Dark Bronze*

• 887 Raw Umber*

• 993 Café Noir

• 190 Bright Aluminum*

• 995 Champagne Mis

• 915 Copperite

• 034 Brushed Aluminum*

• 262 Brushed Nickel Texture

• 996 Brushed Patina

• 997 Cashmere

• 998 Squirrel Gray*

• 443 Smokey Gray

• 276 Mercury*

• 860 Seattle Gray

• 405 Pewter Gray

• 999 Pebble

• 870 U.N. Gray*

• 892 Low Gloss Black*

• 048 Black*

• 637 China Blue

• 919 Sprig

• 685 Royal Navy

• 275 Garnet Red

• 590 Sherwood Green

• 994P Dark Bronze Perforated

• 034P Brushed Aluminum Perforated

All 46 colorways available in 1” slats. *Denotes colors also available in 2”.

1” .008 Gauge Aluminum Metal Blinds

STANDARD PARTS

1.  3/8” Spacer Block*
2. Tape Drum
3. Tilt Rod
4. Tape Drum Support
5. Headrail
6. Headrail End Cap
7. Wand Tilter
8. Tape Spacer
9. Wand Extender
10. Clear Wands
11. Slat
12. Cable Tape Ladder
13. Support Set (Spool Cover) (Part#
14. Cord
15. Assembly with screws
16. Motor
17. Steel V Shaft
18. Aluminum Filler Strip
19. Bottomrail
20. Bottomrail End Cap
21. Button Set
22. Valance Clip
23. Double Slat Channel Valance
24. Hidden Installation Brackets
25. Box Installation Brackets (Optional)
26. Hold Down Brackets
27. End Lock (ordered with Box Brackets)
28. Not Shown: Installation Screw (# 6 x 1.5”)

*Not required on every blind

2” .008 Gauge Aluminum Metal Blinds

STANDARD PARTS

1. End Lock
2. Tape Drum
3. Tilt Rod
4. Tape Drum Support
5. Wand Tilter
6. Box Installation Bracket
7. Clear Wands
8. Cable Tape Ladder
9. Cord
10. Filler Strip
11. Support and Cover Set
12. Lock Assembly with screws
13. Motor
14. Bottomrail
15. Bottomrail End Caps
16. Hold Down Brackets
17. Button Set
18. Valance Clips
19. Single Channel Valance
20. Slat
21. Headrail
22. nd Lock
23. pacer Blocks*
24. “V” Tilt Rod
25. Lift Spool
26. Intermediate Support Bracket
27. Not Shown:Installation Screws (# 6 x 1.5”)

*Not required on every blind

1” Aluminum Metal Blinds Product Specifications

CommercialWindow Treatment Specification
Division 12-Furnishings
Section 12492- Hunter Douglas Architectural Riviera Commercial 1Inch Aluminum Horizontal Blind

PART 1 – GENERAL

1. SUMMARY
   a. Section Includes:
   b. Hunter Douglas Architectural Riviera Commercial 1 Inch Aluminum Horizontal Blind

2. REFERENCES
   a. FLAME-RESISTANT MATERIALS SHALL PASS OR EXCEED ONE OR MORE OF THE FOLLOWING TESTS:

3. National Fire Protection Association (NFPA) 701 (small scale for horizontal applications)

4. Department of Transportation Motor Vehicle Safety Standard 302 Flammability of Interior Materials

5.  California Administrative Code Title 19

6. Federal Standard 191 Method 5903 (used by Port Authority of New York and New Jersey for drapery, curtain, and upholstery material)

7. Boston Fire Department Test BFD IX-1

8.  New York State Uniform Fire Prevention and Building Code
   b. GREENGUARD Gold Certified

9. QUALITY ASSURANCE
   a. SUPPLIER: Manufacturer, subsidiary or licensed agent shall be approved to supply the products specified, and to honor any claims against product presented in accordance with warranty
   b. INSTALLER: Installer or agent shall be qualified to install specified products by prior experience, demonstrated performance and acceptance of requirements of manufacturer, subsidiary, or licensed agent. Installer shall be responsible for an acceptable installation

10. UNIFORMITY : Provide 1 inch Horizontal Aluminum Blinds of only one manufacturer for entire project.

11. DELIVERY, STORAGE AND HANDLING:
    a. Product shall be delivered to site in manufactuer’s original packaging.
    b. Product shall be handled and stored to prevent damage to materials, finishes and operating mechanisms.

12. JOB CONDITIONS:
    a. Prior to shade installation, building shall be enclosed.
    b. Interior temperature shall be maintained between 60°F. and 90° F. during and after installation; relative humidity shall not exceed 80%.Wet work shall be complete and dry.

13. SHOP DRAWINGS:
    a. Show fabrication and installation details for window treatments.

14. SAMPLES FOR SELECTION:
    a. For each color and texture specified, submit 2 sets of samples representing manufacturer’s standard range of finishes for aluminum slats at 6 inches (152 mm) long.
    b. Include Samples of accessories involving color selection.
    c. Window treatments Schedule: Use same designations indicated on Drawings.

15. INFORMATIONAL SUBMITTALS
    a. PRODUCT DATA: Manufacturer’s descriptive literature shall be submitted indicating materials, finishes, construction and installation instructions and verifying that product meets requirements specified. Manufacturer’s recommendations for maintenance and cleaning shall be included.
    b. DRAWINGS AND DIAGRAMS: Wiring diagrams of any motorized components or units, working and assembly drawings shall be supplied as requested.
    c. SAMPLE: Responsible contracting officer or agent shall supply one sample shade of each type specified in this contract for approval. Supplied units shall be furnished complete with all required components, mounting and associated hardware, instructions and warranty.
    d. QUALIFICATION DATA: For Installer.
    e. PRODUCT CERTIFICATES: For each type of window treatments, signed by product manufacturer.
    f. PRODUCT TEST REPORTS: For each type of window treatments, for tests performed by [manufacturer and witnessed by a qualified testing agency] [a qualified testing agency].

16. CLOSEOUT SUBMITTALS
    a. Maintenance Data: For window treatments to include in maintenance manuals.
    b. Sample warranty document

17. MAINTENANCE MATERIAL SUBMITTALS
    a. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.

1” Aluminum Horizontal Blinds Product Specifications Continued

PART 2 – PRODUCTS

1. ACCEPTABLE MANUFACTURER
   A. Hunter Douglas Architectural / 9900 Gidley, CA 91731 /
   Phone: 800-727-8953
   Fax: 800-205-9819/
   Website: HunterDouglasArchitectural.com.
   B. Product substitutions must be approved by architect minimum of 30 days prior to close of bid.

2. PRODUCT : RivieraCommercial 1 Inch Aluminum Horizontal Blind
   A. MATERIALS: Steel headrail and aluminum blind
   B. SIZE SPECIFICATIONS:
   i. Width: Minimum 10-1/2 inches to maximum 120 inches, 144 inches with 2 on one headrail
   ii. Height: Minimum 12 inches to maximum 84 inches
   C. SLATS: 1 inch .008 gauge aluminum slat in dust resistant finish
   D. SLAT SUPPORT: 1.4mm Corded, braided ladder at 22mm spacing
   E. HEADRAIL: Integrated valance, curved steel at 1.376 inch wide by 1.375 inch depth, 0.024 gauge
   F. VALANCE: Optional 2 slat channel valance
   G. BOTTOM RAIL: 1-1/2 inch wide by 1-1/8 inch high steel bottom rail with end cap, optional holddowns
   H. LIFTING MECHANISM: Cordless lift with balanced spring motor
   I. TILTING MECHANISM: Wand tilt
   J. TILT CONTROL WAND: Standard clear wand in control positions [left, right] at heights [12, 20, 30, 40, 50, 60, 70, 78 or 90] inches
   K. MOUNTING HARDWARE:
   i. Box Bracket dimension 1-1/2 inch height by1-1/4 inch depth. Support brackets as required by blind width.
   ii. Hidden Brackets optional
   L. FABRICATION:
   i. Outside Mount: 0 inch deduction from headrail, 0 inch deduction from blind width
   ii. Inside Mount: ½ inch deduction from headrail, ½ inch deduction from blind width
   M. FINISHES
   N . SLAT finish selection from standard selection
   O . SLAT SUPPORT braided ladders shall be color coordinated with slat

3. INSPECTION :
   A. SUBCONTRACTOR shall be responsible for inspection on-site, approval of mounting surfaces, installation conditions and field measurement for this work.
   B. OTHER INTERACTING TRADES shall receive drawings of shade systems, dimensions, assembly and installation methods from subcontractor upon request.

4. INSTALLATION
   A. Minimum depth for inside mount is 7/8 inch with hidden bracket and 1” with box bracket.
   B. Install product level, plumb and aligned with adjacent units per installation instructions
   C. Provide final installation conditions to ensure product is without damage at the time of substantial completion in a dust-free environment

End of Section 12492

2” Aluminum Horizontal Blinds Product Specifications

CommercialWindow Treatment Specification
Division 12-Furnishings
Section 12492- Hunter Douglas Architectural Riviera Commercial 2 Inch Aluminum Horizontal Blind

PART 1 – GENERAL

1. SUMMARY
   a. Section Includes:
   b. Hunter Douglas Architectural Riviera Commercial 2 Inch Aluminum Horizontal Blind

2. REFERENCES
   a. FLAME-RESISTANT MATERIALS SHALL PASS OR EXCEED ONE OR MORE OF THE FOLLOWING TESTS:
   i. National Fire Protection Association (NFPA) 701 (small scale for horizontal applications)
   ii. Department of Transportation Motor
   Vehicle Safety Standard 302 Flammability of Interior Materials
   iii. California Administrative Code Title 19
   iv. Federal Standard 191 Method 5903 (used by Port Authority of New York and New Jersey for drapery, curtain, and upholstery material)
   v. Boston Fire Department Test BFD IX-1
   vi. New York State Uniform Fire Prevention and Building Code
   b. GREENGUARD Gold Certified

3. QUALITY ASSURANCE
   a. SUPPLIER: Manufacturer, subsidiary or licensed agent shall be approved to supply the products specified, and to honor any claims against product presented in accordance with warranty
   b. INSTALLER: Installer or agent shall be qualified to install specified products by prior experience, demonstrated performance and acceptance of requirements of manufacturer, subsidiary, or licensed agent. Installer shall be responsible for an acceptable installation.

4. UNIFORMITY : Provide 2 inch Horizontal Aluminum Blinds of only one manufacturer for entire project.

5. . DELIVERY, STORAGE AND HANDLING:
   a. Product shall be delivered to site in manufacture’s original packaging.
   b. Product shall be handled and stored to prevent damage to materials, finishes and operating mechanisms.

6. DELIVERY, STORAGE AND HANDLING:
   a. Product shall be delivered to site in manufacturer’s original packaging.
   b. Product shall be handled and stored to prevent damage to materials, finishes and operating mechanisms.

7. SHOP DRAWINGS:
   a. Show fabrication and installation details for window treatments.

8. SAMPLES FOR SELECTION:
   a. For each color and texture specified, submit 2 sets of samples representing manufacturer’s standard range of finishes for aluminum slats at 6 inches (152 mm) long.
   b. Include Samples of accessories involving color selection.
   c. Window treatments Schedule: Use same designations indicated on Drawings.

9. INFORMATIONAL SUBMITTALS
   a. PRODUCT DATA: Manufacturer’s descriptive literature
   shall be submitted indicating materials, finishes,
   construction and installation instructions and verifying that
   product meets requirements specified. Manufacturer’s
   recommendations for maintenance and cleaning shall be
   included.
   b. DRAWINGS AND DIAGRAMS: Wiring diagrams of any motorized components or units, working and assembly drawings shall be supplied as requested.
   c. SAMPLE: Responsible contracting officer or agent shall supply one sample shade of each type specified in this contract for approval. Supplied units shall be furnished complete with all required components, mounting and associated hardware, instructions and warranty.
   d. QUALIFICATION DATA: For Installer.
   e. PRODUCT CERTIFICATES: For each type of window treatments, signed by product manufacturer.
   f. PRODUCT TEST REPORTS: For each type of window treatments, for tests performed by [manufacturer and witnessed by a qualified testing agency] [a qualified testing agency

10. CLOSEOUT SUBMITTALS
    a. Maintenance Data: For window treatments to include in maintenance manuals.
    b. Sample warranty document

11. CLOSEOUT SUBMITTALS
    a. Maintenance Data: For window treatments to include in maintenance manuals.
    b. Sample warranty document

2” Aluminum Horizontal Blinds Product Specifications Continued

PART 2 – PRODUCTS

1. ACCEPTABLE MANUFACTURER
   A. Hunter Douglas Architectural / 9900 Gidley, CA 91731 /
   Phone: 800-727-8953
   Fax: 800-205-9819/
   Website: HunterDouglasArchitectural.com.
   B. Product substitutions must be approved by architect minimum of 30 days prior to close of bid.

2. PRODUCT : Riviera Commercial 2 Inch Aluminum Horizontal Blind
   A. MATERIALS: Steel headrail and aluminum blind
   B. SIZE SPECIFICATIONS:
   i.Width: Minimum 10-1/2 inches to maximum 120 inches, 144 inches with 2 on one headrail
   ii. Height: Minimum 12 inches to maximum 84 inches
   C. SLATS: 2 inch .008 gauge aluminum slat in dust resistant finish
   D. SLAT SUPPORT: 1.4mm Corded, braided ladder at 44 mm spacing
   E. HEADRAIL: Square steel head rail at 2.25 inch wide by 1.5 inch depth, 0.024 gauge
   F. VALANCE: Optional 2 slat channel valance
   G. BOTTOM RAIL: 1-1/2 inch wide by 1-1/8 inch high steel bottom rail with end cap, optional hold downs
   H. LIFTING MECHANISM: Cordless lift with balanced spring motor
   I. TILTING MECHANISM: Wand tilt
   J. TILT CONTROL WAND: Standard clear wand in control positions [left, right] at heights [12, 20, 24, 36, 48, 60, 72, or 84] inches
   K. MOUNTING HARDWARE:
   i. Box Bracket dimension 1-1/2 inch height by 1-1/4 inch depth. Support brackets as required by blind width.
   ii. Hidden Brackets optional
   L. FABRICATION:
   i. Outside Mount: 1/4 inch deduction from headrail, 0 inch deduction from blind width
   ii. Inside Mount: 3/4 inch deduction from headrail, ½ inch deduction from blind width M. FINISHES
   N. SLAT finish selection from standard selection
   O. SLAT SUPPORT braided ladders shall be color coordinated with slat

3. INSPECTION :
   A. SUBCONTRACTOR shall be responsible for inspection on-site, approval of mounting surfaces, installation conditions and field measurement for this work.
   B. OTHER INTERACTING TRADES shall receive drawings of shade systems, dimensions, assembly and installation methods from subcontractor upon request.

4. INSTALLATION
   A. Minimum depth for inside mount is 7/8 inch with hidden bracket and 1” with box bracket.
   B. Install product level, plumb and aligned with adjacent units per installation instructions
   C. Provide final installation conditions to ensure product is without damage at the time of substantial completion in a dust-free environment

End of Section 12492

CUSTOMER SUPPORT

 800.727.8953
 HDarchitectural.com

References

• Hunter Douglas Commercial and Architectural products on HunterDouglasArchitectural.com
• Hunter Douglas Commercial and Architectural products on HunterDouglasArchitectural.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>